I've just bought some also, thanks for the review, picked up some great points there, I will take into consideration the depth of the tile adhesive as if it's too thin the spacer simply won't fit

This is a great, thorough review by a normal person, lol. I'm considering these and the points you raise can factor into the job from the start. Think I'll be setting a timer to remind me to remove them.

Great review...I was considering to buy these but your review pointed out issues I had not taken into consideration...so thank you....I think I will stick with the systems I have been using...I think this system would be ideal for smaller tile jobs and wall applications.....if you put them on the floor you can't be walking on your floor for 24 hours...so walking over it a couple of hours later to remove them to ensure you don't break the tee and keep them reusable won't work ...in my opinion....thank you!!!! And your tile job looks good to me....great job

I use those. Love 'em. I don't use on every tile. I level as I lay and only use on those areas that need it so I have less breakage. 👍🏻

Looks great man. Save money anyway you can. I commend you. Salute from the Caribbean.

I've just used mine. Removed after 30 minutes. 🤞 Thanks for the tips

The metal rod is replaceable. If it breaks when taking it out, it can be replaced. Bags of 100 pieces are available for about 5$ to replace the broken ones.

You have done a great job tiling your bathroom well done

I bought Fliessen Schlüssel from Aydinc in Germany. Not perfect, but as I read about the issues with these, I appreciate them more and more. Aydinc’s system uses spring steel wire with two independent legs. They can lift tiles of variable thickness and, if they get covered with mortar, can be wriggled out 100% of the time. Its been years since I bought them so I don't know about availability. They’re not cheap (shipping is expensive from Germany) but worth it.

Thanks for the very useful tips.

Thanks to you. I now remember to loose them. After 20/40min.

I've been tiling for 20 years I'm very fussy. These are ok for the odd tile to pull the corner down. Your suppose to turn the whole thing to clear the adesive around the t bit before leaving it to set. I find that if you cut one side t bit off it's useful to slide between 2 tiles to lift of wall. To apply or scrape of adesive depending whether high or low.. when using on tiles that are no bigger than 300mm by 300mm they can actually push tile appart when tightening. Best advice is to level and straighten walls before tiling using a straight edge. Prepereration is key spend time getting wall right. it will save time and effort in long run getting that perfect Finnish.

Hi been using these for years the reason why you are having these issues 1. The adhesive should be applied to the tiles not the wall leaving an edge clearance of about 10mm. This will allow the clip to rotate and be removed easily. Another good reason for buttering the tile and not the wall this is to allow the grout to reach the wall giving the grout security. 2. This allows you to remove the clips very simply with out breaking the steel clip. They are brilliant and save a bundle on costs and no plastic waste.

Looks great from USA

Very useful. Thanks!

Funniest part was when you started pulling out all the broken ones,Lol. Looks good the tiling you have done though. 👍

looks bloody good mate

Fair play to you fella. Second time of tiling nice job. I'm a carpenter/joiner. Personally I hate tiling. Great Job. Nice one.

I Bought a bunch of them and I love them better than the other ones with the wedges ........great product will be buying more

Great kit

Also for floors put your knee against the closest row cause it will push them around with new backing. If anyone has questions can help

this works well only for wall tiling. for floor tiling, tiles move to the direction where the screw turns together. for floor tiling, clip and wedge works better.

These are a Bitch to get out once thinset dries.But i found the Best use for these is to Use When You Use a Clip and wedge system And you over tighten the wedge causing it to break.Instead of Poppin the thinset covered tile Out and Inserting a New Clup,I use These To Eliminate That Step .Works great.Saves Crazy time Especially when using 1/16 clips which break Often .

Don’t leave them till next day . If you do put the tee in there run it back and forth. Take it out wipe thinset off and repeat.

Have used these before but take them out before the thinset sets they work

I bought 300 of them 2 years ago broke only 6 of them. After I learned how to use them switched completely to them. But for anyone going to buy them read the comments because some of them are creepy. Things the god seller will advertise and provide zoomed pictures to proof. There are no plastic remains they smooth, black nut surface touching tile is smooth. Metal T hook pin is not bending it's springy, made from hard steel. They hand operated with butterfly nut the spanner is for extreme cases only. They made of ABS with glossy finish and mat surface on griping places. The T pin is all same thickness 1mm and the hooking part is 7mm. There is many creepie copies. Good ones they usually over 25€ for 50pcs. Without shipping. Red and black.

Perfect for large format

After twist and pull out, is it tend to lack of adhesive inside the tile?

hi, I`m professional tiler, I using this clips and they do great job for me but yes u must be very careful how long you leave them and I use them in combination with clips with wedges (which you broke after) . Your review is great

thanks for the review was going to buy these but wont

Bella spiegazione x carità non ne ai messo uno ..

कहा से लेना पडेगा

How much po at paano or saan po makakabili niyan tile clips or leveling system

You’re supposed to turn it around, removing any glue from around it, taking it out once, wipe it then install it

No. Also the older version had no make a notch with grinder on wrench to grip right . I repeat never leave them over night make sure it’s dry enough where they won’t move and take out

Doesn’t look a bad job for only your 2nd time

Where can I get in pakistan

I just bought this type of tile level system. I hope it doesn't hurt my job 😱😱😱

All leveling system have problem if you have mud there you put your leveling system

แพงไหม

I would suggest you don't review any items unless you first know how to do a job. I've been a self employed bathroom fitter and tiler forv15 years and this leveling system is amazing. Just because you have no experience it doesn't mean the product is at fault.

The “T” is suppose to snap under the tile. They are replaceable

I ordered 50 pcs, just out of curiosity. If it works i keep them and use. I have 1 main concern about this. Most of my job have uneven walls, so i always have to calculate and feel how to "cheat". I am afraid this product was designed for ideal (fairy tale ideal) circumstances which i think is rare. But will see.

One time use ?

Are you from stoke

Not a tiler, but you're using rapid set adhesive!!!😂😂😂

Broken tile leveling

ใช้ได้กิ่รอบ

Wall

Good luck getting those out to re use. Haha these leveling systems are a horrible idea for a diy guy. For pros using them for LF tile raimondi ones work awesome but I would steer away from this garbage. But what would I know because this is only my 18 year as a tile setter.

you can buy those T pieces alone ....

couldnt have that tile out of line on the right of the window sill oooff!

Don’t use these you won’t get them out took me 8 hours to get out and now have the metal pond snap in tiles and won’t come out, damages tiles edges , shit product , spend more buy rubi system

Omg could you talk any slower????

I'm a professional tiler and these are not that good. They move the tiles as you twist them to tighten them up. That makes them useless as you have to re-align the tiles again. Never come across a tile levelling system that works properly. Use your eyes and run your fingers over the tile joints to feel if they are even.... That's the best way!