Robbie needs to make a Rediit, It's a easy way to connect with fans, and point out some stuff for Robbie, and ofc memes😂

You should be able to wire the clutch pedal to the neutral safety switch relay (from the auto trans) if you do that the manual Ecu should work without needing the whole harness

I remember being this 12 year old kid watching Robbie put wish mods on jasmine and the BRZ and now im 16 with an almost fully rebuilt e46.

You don't need to worry about the manual harness as long as you've got the manual ecu, Nissan ran them as 2 separate ecosystems (ecu and tcu) so if you run the manual ecu it has no idea that an auto box ever existed, the engine loom itself is the same, just unplug the auto ecu and In the engine bay there will be a plug with 2 wires that need to be shorted as its the park/neutral starter inhibit, all 90s nissans were wired pretty much the same.

I put EVERYTHING on hold to watch this. FINALLY MANUAL 😄 More Z content pls!!

always gotta respect ppl who work on their zs by themselves because the way nissan was mounting stuff in the 90s was PAINFUL

"My MUFFLER juice" - what are these dad jokes😑

Robbie I remember watching you back about 4 years ago and I’m super hyped to see you at driven calgary

Let’s hope you replaced the Pilot bushing. Auto transmission bushings are way different than Manual on these z32. Should’ve also gotten the Heavy Duty Clutch Fork with Chromoly pivot ball. Just a fellow z32 owner giving you a heads up from experience 🤗 Also, WiringSpecialties have the MT harness too

Why don't you drain transmissions before pulling them ? Like every damn time you don't do it and fuck everything up

it's funny cause most of the kids saying "ew it's auto" have probably never even driven stick before lmfao

Thank you finally another 300 vid I was getting tired of drifting 😂❤️

Not gonna lie but the shop vibes have seemed so much cooler and relaxed with 2 people again🔥

Saw a 300gt today at work, peeked in the window and saw that it was auto then proceeded to throw up a bit in my mouth. Glad to see there’s one less jdm legend with an auto transmission

I need to replace the clutch pedal on my 92 300zx na...so that is great you will be doing that. Please get some good vid of that..thank you.

U should keep a couple of bags of cat litter laying around u can throw that on oil leaks or any leaks and just crush it and u can sweep it up

MATE THAT ACCENT IS BUSSIN' SHEEEEEEEEEEEEEEEEEEESH

Shoutout to spec, for always coming in “clutch”

Cross threads n red loctite is the best thread always🤷😂

Wiring specialties has the wiring harness, got mine from them

Wild for wearing that white tee in the shop. Also amazed it wasn’t more trashed.

The radiator doesn’t have to be looped. Once all the fluid is drained on the floor then you can keep ports fully open because the trans fluid portion is completely independent on the inside. Had my truck like that since 93

You should really invest in some floor dry. Its cheap,works great, and saves my shop from massive messes every day

U guys are my favorite couple 😆

When are u going to put a catch can on it ???

I love the bell☺️

I always find myself looking at the time when close out of the video happens to see if there’s any extra time left haha cross threads are better than no threads 😂 Keep up the great work guys!

You should make a damn out of kitty litter, that will absorb all the fluids as they spill

U need a manual brake pedal, yes its it different and makes things easier.. otherwise the clutch pedal and the big wide auto brake pedal will be way to close 2 each other.. cheap people just cut it but doesn't look good. Just get a used 1 bolts right on and looks way better. Good luck.

Yupppppppp what we’ve been waiting forrr!!!😩🥵

Fun video...the z is my favorite of all ur cars👌🏾

Also look into getting a motorcycle floor Jack for dropping the trans way better than using regular floor Jack

The giant donut is just a centrifugal clutch that moves the car or transmission under fluid pressure once momentum and inertia increases

Love spec clutch best upgrade you can do

Gotta start doing deletes, to make it easy on yourself. I own a z32na-tt an i really love the car, because its unique.

I'm hyped to see you at Driven Calgary!

Does this mean future z track days. I miss my old Z’s burnout champs…. Had a 89 zx and a 04 350 convertible. Best drift cars ever made in my opinion 👍🏻

Yesss Robbie your amazing ❤️

Been waiting for this moment 🥵

Robbie man. You need to invest in a few bags of speedy dry. Haha

Z committed

“cross threads are better then no threads” had me dead😂😂

Lemme just say… LONG WHEELBASE GANG BABYYYYYY!!! More seats = more fun! Loving the Z32 content brotha!

Exact same internals regardless if it’s a tt or na transmission. Only difference is the ID of the bell housing & the starter engagement on a TT.

Back again lol watching after work

"Not my muffler juice!" I'm weak😂😂😂

Camera quality always crisp. what camera are you using?

Robbie, pull the starter next time and unbolt the torque converter (donut) through the starter hole next time. To get to all the bolts just turn the engine over by the crank or spin the flywheel with a pry bar on the teeth. It won’t make a mess out of the front of the transmission anymore if you have to do any swaps ever again! And pull the pan and drain it next time lol!😆😂 love the videos man! Just a tip from one young mechanic to another!!

"Cross threads are better than no threads"😂

How tf did you find a z32 manual trans. I'm in Sask and I've been looking for months

Fyi, looks like you left the Auto Transmission bushing in on the crank shaft. You needed to remove it and them put in the manual transmission pilot bushing in, then your clutch alignment tool would have worked better.

Robbie, I, and I'm sure all of us absolutely LOVE videos of you working on your car, but could we possibly get videos of you DRIVING your cars? I miss seeing Jasmine, and I wanna see the new K-swap ripppin around.

damn. Robbie started with a blue BRZ and a boatload of wish mods. Now we’re here.

MEGA F, for that muffler, if you loose the liquid inside it means you need to replace the muffler bearings. Very expensive stuff

It’s crazy how we z brothers now my favorite KZfaqr got the same car as me hopefully we meet stay committed guys 👍🙏💯👌🏽💪🏽

@4:45... the song of my people

Not my muffler juice 🤣🤣🤣🤣

spec really comming in clutch huh ?

Robbie. When it comes time to tune this thing, get ahold of tri county auto in new york. You will not regret it. Even if you dont go there, mike'll tell you what exactly you need to make some reliable big power with this girl.

Yess finally

I've done 3 at->manual swaps on Z32. pretty easy.

Would love a q&a video about the swap, I'm manual swapping my z an have nearly a strand of an idea on what to do 😂

Super lit

great video bro!🔥

Cross thread is natures locktite aswell Robbie lol

Robbies Z vs Emerson poo40??

You could sell the muffler juice as Z bathwather lol.

I’d love to see Robbie and @itsjusta6 do a collab. I feel like Robbie’s style and Gavin’s love for speed would make an absolutely wild build come to life.

This is just making me dread doing it myself 😭😭

Just some advice if there's a next time, disconnect the torque converter (donut, lol) from the flywheel before you drop it. You will not have to work around it when dropping it. Also, they will come out together so all of the fluid will not pour out of the converter. Unless you have a transmission jack, there is almost no way of not making a mess. You're still learning though, keep up the good work.

robbie i hope you see this. back when you were working on jasmine when she was still red, and you and videos of you and the boys just boosting around town, it was so entertaining. what happened to all of that?

Draining it should’ve been one of the first things you did lol

You should change the rear main seal before you put the clutch in.

Big no on the manual dude. Now I'm nearly 30 I'm hanging for the time I can get a new car and it'll be auto! 🤣 Mind you (4 knee reckons) in my life hahaha 🤣

9:09 what’s with the infinity badge in the window?

Not the fram oil filter😕

yess!!! just what i wanted to see

Robbie you are the best!!!!

Get the noob outta here! 😂 dope progress

Yesssss

YESSSSSSSSSS!!!!!!!!!!!!

New drift car 🧐

yes

Nice

Thas what I told myself when I ran to my truck after chap stick when I was 21, it'll werk as lube, she didn't care, 😆 ggz

did you keep that AT pilot bushing in when installing? i didn't see it removed before you threw on the clutch. i would imagine that would keep you from getting the trans in, besides the alignment tool being misaligned

Pull the starter and spin the trans over so you can unbolt your flywheel from your torque converter, Jesus dude you said on the s10 video you learned. No messsiesss

Never related to anything more than Chris getting some dirt in his mouth and going yummy

You should reundercoat the car keep it from rusting maybe some herculiner or something under therr

yoooooooooo lets go 🤟🏼

what is muffler juice

Might as well swapped the motor same time lol

Cross threads are better then no threads 😂😂😂😂😂

Wy didn't you removed the transmission pan

LETS GOOOOOO

Why do I have a feeling that they didnt put the pilot bearing in?

On your next transmission, do yourselves a favor and leave the torque converter with the transmission. You'll thank me later.

Robbie could we get a toolbox tour?

lets fucking goooooooooooo

4:45 Cleeter? That you???