Roborock S5 S6 Charging Error 13 Repair - Capacitor not Mainboard or Fuse

Рет қаралды 54,549

Жыл бұрын

Most videos report that for Error 13, if cleaning the charging contacts do not work, you need to change the mainboard fuse. But for S5 & S6, the fault often lies with the charging dock, and in particular the capacitor. I changed the capacitor in 3 of my defective charging docks and they are now all working. I was not able to change the 4th charging dock as I had thrown it away. Try it!
P.s. seems like the PCB for S7 onwards may be different.

Пікірлер: 248

@chriswilliams9071 11 ай бұрын

Man, wish I would have found this video years ago. Bought the cap, swapped it out and haven’t had an error since. So thankful.

@KSToh 11 ай бұрын

Cool. Please like video and subscribe if you are agreeable. 🙏🏼

@ervega 11 ай бұрын

I just tried this with my Roborock S50, I've never in my life worked with circuits or soldering, however, after watching the video I decided to give it a try and it worked like a charm! Thanks so very much for uploading this handy video, you deserve the best!

@KSToh 11 ай бұрын

Good for you! Please like the video and subscribe!

@KSToh 3 ай бұрын

Actually it was also my virgin attempt at soldering!

@halvaroo 10 ай бұрын

I've just repaired my Roborock following your video. Thanks my friend.

@KSToh 10 ай бұрын

Great! Please like video and subscribe!

@spoloborota2 Жыл бұрын

Thanks a lot! Changed the fuse in the dock and it started charging correctly again!!! Writing it after 5 successful chargings!

@KSToh Жыл бұрын

Cool. Please like my video and subscribe!

@DallasGoh 4 ай бұрын

Thanks for the tutorial. Never tried soldering before but managed to complete the fix and got my robot working again

@KSToh 4 ай бұрын

Nice work! Please like and subscribe!

@TPMil 11 ай бұрын

Thanks a lot for this easy and cheap fix :-) Before the fix I was getting the error 13 after every clean, it's now working perfectly for more than 2 weeks (clean every day)

@KSToh 11 ай бұрын

Nice! Please like video and subscribe.

@RemySoeters1 Жыл бұрын

Never soldered anything. Wanted to give it a try with this video. Now no more error 13. Works like a charm. Cheers for the video!

@KSToh Жыл бұрын

Great! I was also a virgin solderer doing it for first time!

@SimonSays__ 11 ай бұрын

Protip when soldering. Heat up both places. The board and the pin.. and apply solder to the pin.. not the solder iron. 😊

@KSToh 11 ай бұрын

@@SimonSays__ oh. Did not know that. Is it safe to heat up the pin?

@SimonSays__ 11 ай бұрын

@@KSToh It is, if you heat up both the pin and the pad it takes about max 10 seconds. Then apply soldet to a little blob. It fills the hole nice. Othervise there is just a solderblob stuck to the pin... not really attatched to the board.

@nilfisktun Жыл бұрын

My man! This fixed our beloved 7 year old roborock! Swapped there fuse inside, twice, but after all, this was the culprit!

@KSToh Жыл бұрын

Good for you. Please like the video!

@Swanicyouth Жыл бұрын

Thank you for this. Saved me from buying a new vacuum for a $3 part!!! I previously changed the thermal fuse thingee on the motherboard. That helped error 13 for a little bit, but it came right back eventually. This capacitor / procedure fixed it. So far so good, no error 13 after about 20 runs & it used to happen 80% of the time. Be careful what capacitor you order people. First one I ordered was correct spec but way too tall to fit. The second one I got was similar specs & just a hair smaller. That one worked. I dunno if it matters, but the capacitors do have polarity. The side with the dash or line is negative.

@KSToh Жыл бұрын

Cool. Please like my video. I believe polarity matters.

@KSToh Жыл бұрын

I believe polarity matters.

@ygsrinivas 11 ай бұрын

Can you please share the link you ordered from ? I could not find it anywhere. Thanks

@KSToh 11 ай бұрын

@@ygsrinivas Get from electronics store at your place. If not, get from www.aliexpress.com/item/32885198522.html?spm=a2g0o.productlist.main.1.56b51a830Q1KNW&algo_pvid=56ae61e5-5a1b-4cae-8973-e91f4c6b0aef&algo_exp_id=56ae61e5-5a1b-4cae-8973-e91f4c6b0aef-0&pdp_npi=3%40dis%21SGD%213.04%212.64%21%21%21%21%21%40211bda9b16872485278967299d0829%2165715848148%21sea%21SG%21841320141&curPageLogUid=L0ZlIb1iuPLa

@Zork1337 6 ай бұрын

Thank you so much for this video! It saved me some money. Just bought a capacitor for 3,5 euro. It was bit large but I bend it over the transistors. I put some gun glue between legs of the capacitor to prevent short circuit the capacitor. Works like charm!

@KSToh 5 ай бұрын

Cool. Please like video and subscribe.

@garysinclair6490 9 ай бұрын

I just did this fix on the charging base on S5 dock from 2019 and it was successful. Thanks for the video.

@KSToh 9 ай бұрын

Cool. Please like video and subscribe!

@arturasr 8 ай бұрын

I managed to fix my Roborock S5! You are a genius, thank you so much for the info!😎🤣🍾👍🤘

@KSToh 8 ай бұрын

Glad to help. Please like video and subscribe.

@davidpachecoegido Жыл бұрын

I did it yesterday and so far it has 4 full charges so this has worked, thanks!

@KSToh Жыл бұрын

Cool. Please like the video!

@tespiteng 3 ай бұрын

Successfully repaired my S5 with your instructions (with a 68uf 400v capacitor) . Thank you very much 👍👏

@KSToh 3 ай бұрын

Great 👍 please like video and subscribe!

@vasiliisukhachev7602 3 ай бұрын

Did the same but found that it is still not charging properly when above 80%. Did you notice the same?

@KSToh 3 ай бұрын

I did not have this problem.@@vasiliisukhachev7602

@vasiliisukhachev7602 3 ай бұрын

It also feels like it more often charges without an issue after some time. Do you know what else can be checked?

@raymond22112376 16 күн бұрын

My Roborock S5 charger is fixed. Thank your very much for your efforts making this video.

@KSToh 12 күн бұрын

Happy to help. Please like video and subscribe.

@KT-lw5tq Жыл бұрын

Did the same thing. Replaced the 420v68uF with a Rubicon 400v68uF. I kinda tested it first cause i did not know if the circuit handled the lower voltage. It seems okay for now. Charging without problems. Done in 15 minutes. Thanks for the guidance and tip.

@KSToh Жыл бұрын

Cool. Please like the video.

@greegp7400 Жыл бұрын

Yep it is working, yesterday I change it and charged perfectly!!! Thank you 😊

@KSToh Жыл бұрын

Good for you. Please like my video.

@svene.2430 Жыл бұрын

Thanks worked perfectly for my S50 error 13 👌🏻

@KSToh Жыл бұрын

Great to hear! Please like my video.

@bummelmann2000 8 ай бұрын

‼️‼️ DANGER ‼️‼️ ATTENTION ‼️‼️ You should be informed in detail about the subject of electrolytic capacitors beforehand. It should definitely be unloaded beforehand. There can be voltages of over 300V at the Elko. It is also important to pay attention to the installation direction. An electrolytic capacitor has a plus and minus pole. If the connection is incorrect, there is a risk of an explosion, which can be dangerous. Therefore, do not handle it as carelessly as shown here. GOOD LUCK and good success! 😊

@KSToh 8 ай бұрын

Thank you for the warning! I thought I was careful but your warning is still good!

@user-hn7wc8mi1n 7 ай бұрын

Thanks for the great video. My S50 is changing as per normal after this fix.

@KSToh 7 ай бұрын

Great to hear! Please like video and subscribe!

@youdntube 7 ай бұрын

The same problem with my charging base. 47uF/400V also worked at my side. Not sure if it will work for everyone. Thank you for this video! Watch out! There is high voltage on this capacitor (even over 300 V). Follow the guide how to discharge.

@KSToh 7 ай бұрын

Cool. Please like video and subscribe!

@carloszz8 10 ай бұрын

It works !! thank you very much for the video. Very clear, very easy. First time for me to sold and no problem to make it

@KSToh 9 ай бұрын

Glad it helped. Please like video and subscribe!

@taoahler Жыл бұрын

I swapped the capacitor to a Nichicon quality capacitor and now it charges perfectly again. Thank you :-)

@KSToh Жыл бұрын

Cool. Please like my video!

@knotthugu 11 ай бұрын

Same here

@KSToh 11 ай бұрын

@@knotthugu cool. Please like video and subscribe. Thanks.

@annespacedroid Жыл бұрын

Cool video & thank you. Nobody did one for the cap repair in the dock. Can I say, adding a little extra solder to the cap pins will make it easier to remove as it gets all the solder flowing. Get a good quality cap if you intend to undertake this job.

@KSToh Жыл бұрын

Thanks! It’s my first time soldering on PCB. I did add some extra solder at first but did not get me anywhere. I am a novice here. I did buy a reliable Rubycon capacitor but the seller supplied me dubious Chongx capacitor. I did not realise until I was reviewing this video! Please subscribe.

@annespacedroid Жыл бұрын

@@KSToh My friend... If that's your first time, you did well. The reason why I stated "good quality cap" is because I did what you did exactly including the rubycon to generic "bait & switch". After changing mine it worked... For 20 minutes then the dock exploded. Opened it back up to find the cap legs had arced across & left a black carbon Arc on the board. That event took out 2 diodes, the main fuse & had completely vapourised 2 tracks on the circuit board. I suspected the cap & removed it to find it was reading around 61uf instead of the 68uf rating. Should have checked it first. That alone shouldn't cause the dock to go bang as the original was reading 57uf. Something about that cap caused a high voltage Arc between its pins on the board. Now, as stated before.... You did well. If you get some soldering flux and put a little of it with the extra solder it really makes a difference. Your iron tip should be clean and silver shiny. If you have layers of black carbon then your iron isn't actually touching the solder & that's commonly the reason why you need to push the iron hard into the work. That cracks off some of carbon & a small surface of your iron now touches the work. Simply wait until the iron is hot enough to use & dip the tip in the same flux & then you can easily solder. Ps I got my $5 back on the dodgy cap....... Unfortunately the damage it did was worth more =(

@annespacedroid Жыл бұрын

@@KSToh Update: Got the diodes, fuse & low esr cap today. Repaired the tracks on the board, installed the diodes, cap & fuse. All working again =)

@KSToh Жыл бұрын

@@annespacedroid nice!

@TechnicalLee Жыл бұрын

@@KSToh Buy a new tip for your soldering iron, yours it all oxidized so you had a lot of trouble getting heat transfer. A good tip should be shiny. If you see the tip starting to turn brown, your iron is too hot and you should turn down the heat.

5 ай бұрын

Awesome. Thank you very much, man! This solved the charging problem for me as well.

@KSToh 4 ай бұрын

Nice. Please like and subscribe!

@yasintr Жыл бұрын

It worked like a charm. Thanks a lot!

@KSToh Жыл бұрын

Cool! Please like the video.

@duri3 Жыл бұрын

Thx! Just fixed my Docking Station with a new capacitor

@KSToh Жыл бұрын

Nice work! Please like my video!

@bilkao 17 күн бұрын

Hello, I solved my problem thanks to your video. Thank you so much for sharing.

@KSToh 17 күн бұрын

Glad it helped. Please like video and subscribe!

@TiborPichner Жыл бұрын

Thanks, I fixed it based on your video.

@KSToh Жыл бұрын

Cool. Please like my video.

@Kengw204AMG 11 ай бұрын

Thanks for your kindly advice. I also can fix my Mi mop1c with the same problem just replace that capacitor. A bit hard to solder but it’s worked!! Thanks again ✌️ you save me 30$ for the new charging dock LoL

@KSToh 11 ай бұрын

Cool. You took this idea and applied to another robot. Please like video and subscribe.

@KimElman 10 ай бұрын

Worked like a charm! Many thanks!! 🙏

@KSToh 10 ай бұрын

Glad it helped! Please like my video and subscribe!

@KimElman 9 ай бұрын

@@KSToh I did. However now is back to the same error after a few runs 😕 bad quality spare part or some underlying issue? What do you think?

@KSToh 9 ай бұрын

@@KimElman hi. It’s unfortunate. Maybe you try using a different brand capacitor? If it happens again, then problem may be elsewhere.

@gustavhoo 10 ай бұрын

Awesome soldering technique 🫣😳😘🤪 I will try my friends charging dock, and if it works I will try your fix! Thanks for the video! 🙏

@KSToh 10 ай бұрын

No no. The solution may be awesome but the soldering is bad, my friends tell me. If it works, please like video and subscribe!

@markhindson4621 Жыл бұрын

Thanks. Replacing thjs cap so far looks to have fixed mine

@KSToh Жыл бұрын

Glad it helped. Please like my video!

@skochevtsev 3 ай бұрын

Worked for me, thanks for the video! I also replaced the fuse, I wish I did your video first 😂

@KSToh 3 ай бұрын

Glad it helped! Please like and subscribe!

@davidfiori3861 Жыл бұрын

This fixed mine, thank you!

@KSToh Жыл бұрын

Cool. Please like the video.

@oloferiksson3844 3 ай бұрын

Working perfect. Many thanks :)

@KSToh 3 ай бұрын

You're welcome! Please like video and subscribe!

@xdomingo 9 ай бұрын

Worked like a charm, thank you very much :-)

@KSToh 9 ай бұрын

You're welcome! Please like video and subscribe!

@kenthosselton 4 ай бұрын

This worked for me. Thanks so much!

@KSToh 4 ай бұрын

You're welcome! Please like and subscribe.

@TheDeadinhollywooD 6 ай бұрын

Thank you. Solved my charging problem.

@KSToh 6 ай бұрын

Cool. Please like video and subscribe.

@cuntanmarius3805 Жыл бұрын

seems to be working now, thx!. im using an 68 450v cuz its the only one that ive found

@KSToh Жыл бұрын

Nice. Please like and subscribe. Thanks.

@annespacedroid Жыл бұрын

A higher voltage cap is fine.

@anaceleste2676 Жыл бұрын

My Roborock S7 had this charging error and it was because the part of the floor where I placed the base was uneven. I relocated the base to a spot where the floor was level and the issue was resolved. So, you can try that, maybe works in some cases.

@KSToh Жыл бұрын

Thanks for the tip!

@mykiahendricks6512 Жыл бұрын

mine has not been charging for about a week so after seeing this comment i moved the dock over the slightest bit and it is now charging. THANK YOUUUU!

@vikini85 11 ай бұрын

Thank you so much!

@hristogurvanov9206 7 ай бұрын

Thanks, worked perfectly!

@KSToh 7 ай бұрын

You're welcome! Please like video and subscribe!

@tepanek Жыл бұрын

Thank you for this movie!

@KSToh Жыл бұрын

Cool. Please like my video!

@fillwe4600 Ай бұрын

Thank you! Seems to have fixed my issue

@KSToh Ай бұрын

Great to hear! Please like video and subscribe!

@zecaafonso6758 10 ай бұрын

Worked for me. Thanks mate 😊

@KSToh 10 ай бұрын

No problem 👍 please like video and subscribe!

@ducttapetech9885 2 ай бұрын

Its very important to add a glob of flux to the pins of the capacitor when soldering and desoldering. Application of the iron to the joint should provide almost instantaneous solder liquidation with the use of flux. Great video and am just offering a tip to soldering novices.

@KSToh 2 ай бұрын

Great tip! I am a soldering novice. Please like and subscribe!

@yeahnah6468 11 ай бұрын

Legend. Thanks, just did this.

@KSToh 11 ай бұрын

Cool. Please like video and subscribe.

@chansJar Ай бұрын

Thanks for the video, it pointed out a clue. About a month ago I replaced the capacitor with a new one (high quality Panasonic 400V/68uF), unfortunately today the problem returned, the device charged to more than 80%. If I understand correctly, its function is to filter input voltage fluctuations (in my case it's 230V, so with a tolerance of 10% 253V). Taking this into account, the voltage value of the capacitor should be above 356V, so 400V is theoretically sufficient. Could it be that something else is the problem in the power supply circuit? I'm thinking of changing to a capacitor with a higher voltage and higher capacitance, just not sure if it will fit.

@KSToh Ай бұрын

To be honest, I have no idea. If the robot does not keep moving off the charger, seems like it is not a charger issue.

@mirekszylkiewicz8529 11 ай бұрын

what is the voltage at the output of the power supply module in a working charging station? The power supply in my station is very damaged (Q1 shorted, blown fuse), I wanted to replace the power supply with a laptop charger, but I'm not sure if it should have 20V at the output

@KSToh 11 ай бұрын

I read it is supposed to be 4.3V without load and 20V with load.

@lowchuanjie8633 Жыл бұрын

Did you encounter error 109:fan open circuit? Or do you have video on it?

@KSToh Жыл бұрын

No. But to reach the fan, watch my Error 10 video. kzfaq.info/get/bejne/g7R1ZLd438eslZs.html

@Akerfeldtfan 10 ай бұрын

I just replaced mine- took about 15 minutes tops, very easy. I put the robot on and it charged straight away. That might be dumb luck, but I am hopeful. Will report back!

@KSToh 10 ай бұрын

Great. Please like video and subscribe!

@Akerfeldtfan 9 ай бұрын

Following up to say that it has fixed the issue. The vacuum has not had error 13 since doing this. Others might still have issues associated with that mainboard fuse, which I also replaced a while ago. Thank you so much for sharing this, it has fixed a massive annoyance with 15 minutes work.

@KSToh 9 ай бұрын

@@Akerfeldtfan nice!

@mehmetalieyuboglu3642 3 ай бұрын

Thank you so much friend

@KSToh 3 ай бұрын

Glad that it worked for you! Please like and subscribe!

@Ducatisti92 7 ай бұрын

I have the same issue with the S7 MaxV Ultra Docking station. Any ideas where the capacitor is on that dock?

@KSToh 7 ай бұрын

Honestly I have no idea. I don’t have your model. Should it not be similar?

@MrTandstad 9 ай бұрын

I had the error 13 on my Roborock S50, so I bought a Roborock S6 pure. Then I saw this clip, and ordered the capasitors from AliExpress. While waiting, I figured if Roborock S50 and S6 pure has the same docking, S50 should work with my s6 docking. Tried it, but still error 13. Perhaps I will try the sandpaper one next.

@KSToh 9 ай бұрын

If your S50 has the same error 13 when placed on the S6 dock, then the problem is with your S50 and not the S50 dock. To verify, place the S6 on your S50. If still error 13, then maybe both docks need replacement capacitor 🤷🏻‍♂️

@SonicTheHedgehogFan2023 11 ай бұрын

Forgotten tip: I saw your robot's dock. Tip's point: If your robot's dock is on a wooden floor, u should put there a plastic mat at the floor, in the front of your dock. The plastic mat (AKA Moisture Proof Mat or MPM) looks like a plastic circle, but cutted after a form of a cockroach's head. You put the plastic mat in the front of your robot's dock on the floor, and then move your robot manually to its dock, and then it charges. Warning: Do not get wet the plastic mat, otherwise the wetness will cause moisture damage to the MPM, and Error 13 will happen again. This may work.

@KSToh 11 ай бұрын

I have the plastic mat. It came with my S5/6. I use it on my wooden floors. Don’t think it makes a difference for Error 13.

@user-nx6iy2ot2p Жыл бұрын

Hello, I identified the problem with the base since on another base my vacuum cleaner works. On the other hand, I tested the current capacitor and it gives me 58uF, the output voltage of the card is indeed 20 volts, have you tested your capacitor. for you even with these values is he the culprit? Thank you for your answer because it bothers me to change the 2 complete cards. Have a good evening

@KSToh Жыл бұрын

Hi. I did not test the capacitor itself. I tested the charging dock and it seems ok. But I changed anyway and the problem resolved. Maybe the capacitor will always work initially but not sustained?

@user-nx6iy2ot2p Жыл бұрын

@@KSToh Hi, thanks again for your tutorial and your advice, I ended up changing the capacitor and I'm so happy, it charges correctly, it's great. Thanks a lot. good continuation to you

@KSToh Жыл бұрын

@@user-nx6iy2ot2p cool! Please like my video.

@a11aaa11a Жыл бұрын

I have an auto-empty dock and a normal one, the auto empty kept giving this error so I tried the normal one and it worked so I assume this capacitor is the issue; do you know if I can just switch the boards entirely? Or at least just rip out the capacitor from the good one and put it in the broken one?

@KSToh Жыл бұрын

Yea I believe the capacitor is the culprit. Based on my limited knowledge, it seems difficult to transfer capacitors. Please confirm the specs are the same. I don’t know if you can switch boards. Does the auto-empty board have more functions?

@a11aaa11a Жыл бұрын

@@KSToh yeah it also empties the bin. I'll just get the $3 part I guess, I'm just manually docking in the meantime which seems to work

@anapaulabrucoli8984 Жыл бұрын

Thank you soooo much!!!!

@KSToh Жыл бұрын

Did it work for you? If it did, please like my video!

@anapaulabrucoli8984 Жыл бұрын

I'll try but allready left the like 😊

@serdarozen1918 9 ай бұрын

Aynen değiştirdim 450 v 68mf taktım düzeldi çok teşekkür ederim

@KSToh 9 ай бұрын

Very good! Please like video and subscribe.

@Sento1968 Жыл бұрын

Hola, que tension en bornas tiene que haber?. A mi me da 4,5Vdc.

@KSToh Жыл бұрын

Without load, supposed to be around 4.3V. With load, should be around 20V. But no point measuring. It will measure fine but still not work. Just replace the capacitor.

@nimr0d85 8 ай бұрын

Thank you for the correct hint to repair my robot! (Even though the video itself is horrible.)

@KSToh 8 ай бұрын

Haha. Sorry about the video. Please like anyway and subscribe.

@pedroteixeira2003 Ай бұрын

Hey! Thanks for the video! My vacuum is completely dead so I’m not certain that this is the problem! With a pole finder the station still has power in the contacts. Does that mean the station is fine? Thank you!!

@KSToh Ай бұрын

If the battery does not charge at all, it should be a dead battery. Change that.

Жыл бұрын

Nice! I am going to do it!

@KSToh Жыл бұрын

Have fun! Please like my video.

Жыл бұрын

@@KSToh I just found a 450V capacitor. What do you think? Is that also good?

@KSToh Жыл бұрын

@ 450V should be fine. Please update!

@philipmois Жыл бұрын

What was the voltage output of the base before the repair? Mine shows 4.3 volts

@KSToh Жыл бұрын

Without load, supposed to be 4.3V. But this does not tell you anything. The capacitor can still be defective.

@szupe 9 ай бұрын

I have just also replaced the capacitor, thx! So far charging again but need to do a few days testing. (I have PTSD from this random "Charging error..." message.) Btw. I have measured ~60 uF on the original capacitor which is still looks okayish capacitance. Whave you measured the wrong ones? How could it be the root cause if measured capacitance is not too much out of range? 🤔

@KSToh 9 ай бұрын

Error 13 is random. My capacitor also looks fine. I never bothered to measure. Just replace and the problem solved. Please like video and subscribe!

@TechnoLogic2016 Жыл бұрын

All that things worked because you unplug the station from the 110/220. Unsoldering and put it back the capacitor also worked great for me, but the capacitor was - ok, 68uf, as written, so put it back old one. Anyway, I discharge it and put back, 4-5 times from this point - no problems

@KSToh Жыл бұрын

If you discharge the capacitor, it should work again. But after a while, the problem will recur and you need to replace the capacitor.

@TechnoLogic2016 Жыл бұрын

@@KSToh thanks! What is the physics of this problem with the capacitor?

@KSToh Жыл бұрын

@@TechnoLogic2016 no idea 🤷🏻‍♂️

@ecaribel 3 ай бұрын

In some videos people replacing fuse inside vacuum, not inside dock station. How can I understand which tutorial should I go through?

@KSToh 3 ай бұрын

From my experience, 90% of the time, replace the capacitor in the docking station.

@ecaribel 3 ай бұрын

@@KSTohAny way to detect it? :)

@KSToh 3 ай бұрын

I tried to measure the voltage but reliable.

@andreasdu1 2 ай бұрын

Ich denk bei fehler 13 soll man PTC Widerstand B0185 wechseln. Was denn jetzt?

@taramohamadpur8844 7 ай бұрын

Hi do I have to plug out my roborock if I’m not using it for a week?

@KSToh 7 ай бұрын

Nope. I leave it on 24 x 7 x 365 days.

@johnyefx5748 4 ай бұрын

Your capicator looks ok, how do you know that capaicator needed to be replace in first place?

@KSToh 4 ай бұрын

I read up and was told it should be the capacitor.

@Strange1_au 4 ай бұрын

Just took mine apart and replaced the capacitor with a 68uF 400V, but then found out that the original was a 47uF 420v! I haven't powered it on yet but should I swap it back and source a new 47uF?

@KSToh 3 ай бұрын

I have replaced for several S5 & S6 and they are always 68uF. So it’s strange yours is different. If yours is S5 or S6, I say go ahead to use 68uF. If yours is different model, I would be cautious. Although the internet seems to say it’s fine.

@Strange1_au 3 ай бұрын

@KSToh It's an S5 MAX. I ended up putting the original 47uF back in while I ordered new ones. Since then it hasn't had the problem so I've got new ones here just in case!

@KSToh 3 ай бұрын

@@Strange1_au seems like removing the capacitor and putting it back again is a new solution!

@muhammadshafiqrosli6414 4 ай бұрын

How to know which capacitor that need to replace? Mine is S5 Max. Below I attach video for the board

@muhammadshafiqrosli6414 4 ай бұрын

kzfaq.infoyMYPZ5BWH4w?si=KDqBAwNxlSBh-ENE

@KSToh 3 ай бұрын

Unfortunately I have to admit I do not know about S5 Max.

@user-zb4kx1ck8e 9 ай бұрын

Thank you very much for the video, but before I fixed the repair, I checked with a working charger of my parents. There is still the problem even after replacing a working charger. What could it be besides a charger???? Thank you .

@KSToh 9 ай бұрын

If your parents’ robot works when placed on your charger, then the charger is good and your robot is bad. Otherwise maybe both chargers are bad? If the robot is bad, then maybe it’s the robot motherboard. Beyond my knowledge, sorry!

@c.c.rogado8416 7 ай бұрын

Si no es la base de carga suele ser el fusible autoreseteble de la placa electronica

@MrHrrmarques Жыл бұрын

it worked, even after replacing the mainboard fuse, error 13 persisted. Solved after repairing the base ....

@KSToh Жыл бұрын

Glad it helped. Please like video!

@DSBenny 4 ай бұрын

Hi. Do you have more info about the fuse thing? Thx

@KSToh 3 ай бұрын

Fuse - I have no idea. Sorry. 🤷🏻‍♂️

@per5hak0v 6 ай бұрын

Спасибо, это помогло!!!

@KSToh 6 ай бұрын

Nice. Please like and subscribe!

@Eichhorn23 9 ай бұрын

Hi! Which Capacitor do I have to replace in the S5max version? I opened the docking-station and there are different parts than in the s50. Does anyone know the answer?

@KSToh 9 ай бұрын

I don’t have the S5 Max but can you look for one that is the same specs?

@Eichhorn23 9 ай бұрын

I did, but there is no one with the same specs.🤔

@KSToh 9 ай бұрын

For S5 & S6, there is only one big capacitor. Do you mean the S5 Max is very different? Do you have a picture?

@Eichhorn23 9 ай бұрын

How can I send a picture?

@sargentokoala 11 ай бұрын

hi, someone, might tell me whats word is in the ntc1 just near to this capacitor? thanks

@KSToh 10 ай бұрын

Sorry. I did not answer because I don’t understand your question.

@-AishwaryaKadam 8 ай бұрын

Replaced capacitor. No luck. Any suggestions? Regards.

@KSToh 8 ай бұрын

If error 13 persist after replacing capacitor on the charging dock, then problem is due to other reasons. 🤷🏻‍♂️

@-AishwaryaKadam 8 ай бұрын

Please suggest. Regards

@NRJRCE 7 ай бұрын

motherboard can do a repair on it

@romanreimer4322 Жыл бұрын

how did you come up with the idea that you need to change the capacitor. you didn't take any measurements, did you?

@KSToh Жыл бұрын

The idea came from someone. I credited him in my video. I did take measurements but not conclusive.

@lilbabygroot 9 ай бұрын

What capacitor should I buy??

@KSToh 9 ай бұрын

It’s specified in my video.

@pietervp6058 Жыл бұрын

What capacitor do i need to order?

@KSToh Жыл бұрын

68 uF 400 to 420V

@KSToh Жыл бұрын

@@daylightsaver oh dear!

@user-io5lc2wz1q 6 ай бұрын

Can someone share where can I buy the capacitor from?Thank you

@KSToh 6 ай бұрын

Can try this? s.click.aliexpress.com/e/_mOl7aoy

@KSToh 6 ай бұрын

Maybe this better quality? s.click.aliexpress.com/e/_mLKxGLw

@tureanbogdan4166 Жыл бұрын

How did you know it was defective?

@KSToh Жыл бұрын

Calculated guess?

@romanreimer4322 Жыл бұрын

fake Video?

@zsoltkallos437 Ай бұрын

Hi Everybody! I have Roborock S5, and the charging is not working, the vacuum cleaner always come off form the charger. How can i find out if the charger is the problem, or the battery or the vacuum cleaner mainboard? Thx in advance!

@KSToh Ай бұрын

If the robot keeps coming off the charger, it is very likely the charger. If the battery is no good? The robot will just stop working.

@alexanderfainchtein8929 8 ай бұрын

Had the same problem replaced the campastore now have a new problem with the laser ...

@KSToh 8 ай бұрын

kzfaq.info/get/bejne/qLx-m5Nky9bNomg.htmlsi=ewcsmZ13NODKvpda

@marcinlag1 7 ай бұрын

68uF 450V Will be ok?

@KSToh 7 ай бұрын

Not entirely sure. Should be fine but the size may be bigger and cannot fit?

@marcinlag1 7 ай бұрын

@@KSToh it solved problem with error 13. 450 is a bit high but finally it fits. So I recommend 400 or 420.

@KSToh 7 ай бұрын

@@marcinlag1 nice. Please like video and subscribe!

@dougfernans 10 ай бұрын

how do you knew that this capacitor was defective?

@KSToh 10 ай бұрын

Someone suggested. I credited him in my video.

@ginorosa76 10 ай бұрын

O riparato e il costo di €4,90 grazie mico 👍

@KSToh 10 ай бұрын

Nice! Please like video. Please subscribe!

@theresachung703 4 ай бұрын

How do you know so much?

@KSToh 3 ай бұрын

I actually don’t. Some I experiment, some I learn from others.

@pstrsvole948 10 ай бұрын

Roborock s6?

@KSToh 10 ай бұрын

Same. I repaired my S6 charger too.

@RhysCHarris 6 ай бұрын

FYI for anyone with S5 Max, the inside of the dock looks different, so this won't work

@KSToh 6 ай бұрын

Noted with thanks.

@ArielBrener 8 ай бұрын

I replaces the charging unit - the error continues.... I also replaced the battery - still error 13 charging error

@KSToh 8 ай бұрын

If your replacement charging unit is new or confirmed working, then problem is not with charger. Battery has nothing to do with error 13. Where did you get your replacement charging unit?

@ArielBrener 8 ай бұрын

@@KSToh My mom Has the same model - so I used her (working) charging unit. Its an original one.

@GingerNingerGames 4 ай бұрын

Unfortunately didn't work for mine, so it's going to be the fuse on the mainboard for me.

@KSToh 4 ай бұрын

🤔

@GingerNingerGames 4 ай бұрын

@@KSToh I've measured the fuse, it's 1Ohm, it should be 0.15ohms max, so definitely the fuse in my case, just thought I'd verify that for others.

@bmxpepe 11 ай бұрын

didnt work for me. Will try thermistor next.

@KSToh 11 ай бұрын

This is unfortunate. Hope you find the fix.

@TheKauniukas 3 ай бұрын

Replaced it,but still the same problem 😔

@KSToh 3 ай бұрын

Oh.

@HOTAIR83 7 ай бұрын

A wystarczyło wcisnąć przycisk RESET na 30s.

@KSToh 7 ай бұрын

???

@Hehelii 6 ай бұрын

Hej, patent z resetem działa?

@HOTAIR83 6 ай бұрын

@@Hehelii Tak ale to wtedy kiedy opcja z wymianą kondensatorów nic nie da. Bateria jeśli jest w pełni naładowana i robot na niej odkurza to po takim cyklu odkurzania jednym np mały pokój gdy robot wróci z nową baterią lub po naprawie wymianie ogniw to wtedy ładowanie ruszy. Reset to jedna z opcji.

@KSToh 6 ай бұрын

Gwarantujemy, że samo naciśnięcie przycisku resetowania nie pomoże rozwiązać problemu z błędem 13.