Roborock S55 | Error 13 | Mainboard fuse exchange

Roborock S55 | Error 13 | Mainboard fuse exchange | check description

Рет қаралды 26,970

2 жыл бұрын

This method works for many Roborock models.
Please do follwing steps:
1. Clean power pads (vacuum & charger). Test the system. If does not work, go to step 2.
2. Check charger voltage. It should be ~4,2V without load and ~19,6V with load. If the voltage is correct, skip to step 3.
3. It looks like your fuse is damaged. Please replace it according to this video.
Fuse model: RUEF300 PTC 3A 30V
New fuse costs ~0,2 USD.
Other helpful video (for Roborock S50):
• [EN] Roborock S50 - Er...

Пікірлер: 28

@zsoltkallos437 Ай бұрын

Hi Everybody! I have Roborock S5, and the charging is not working, the vacuum cleaner always come off form the charger. How can i find out if the charger is the problem, or the battery or the vacuum cleaner mainboard? Thx in advance!

@YZFMANIAC08 2 жыл бұрын

Nice job, thanks for explanation 👍🏻✌🏻

@plawp69 2 жыл бұрын

I went into this with no soldering experience. When I took the bad fuse off, there were two reddish rectangles underneath. Are those solder pads? I removed those too and there was a metallic material underneath the red rectangles. Was the new fuse supposed to be soldered to those red pads?

@q3bing 2 жыл бұрын

May I ask where did you get the replacement fuse in the US? Thanks!

@bm2088hp 5 ай бұрын

This fixed the Error 13 on my Roborock E25, thanks!

@TechDayEveryDay 5 ай бұрын

You are welcome;)

@davidfiori3861 Жыл бұрын

In my S50, fixed the charging error by changing the main capacitor in the charger. 10 minute job.

@tomaspalencia877 6 ай бұрын

Yessss it works. Thanks for sharing my roborock is back!

@TechDayEveryDay 6 ай бұрын

You are welcome

@bestcar6156 Жыл бұрын

Dziękuję Robrock s55 śmiga teraz super :)

@TechDayEveryDay Жыл бұрын

Proszę bardzo :)

@bogdaniosip492 2 жыл бұрын

Measured the resistor and it shows 0.15-0.4 values. Jumped it with a wire just to be sure....stil have the same error...any help? Battery ang charging station measures where ok. Also switched the battery Frome and with a friend's robot and his work fine with both of them, mine gets the error 13 with both ones

@pawelkdi 2 жыл бұрын

it works thanks !!!

@ryana42 4 ай бұрын

Where do you get a fuzz like this? How Do I know if it applies to the s7?

@marcocornell7310 2 жыл бұрын

Moin, ich habe das selbe Problem wo kann ich so eine Sicherung bekommen? Gibts irgendwo auch einen Schaltplan?!

@jorgech.997 5 ай бұрын

Hi, temp of the air flow?

@eshtrum 2 жыл бұрын

What is the liquid that you put on the bad fuse to take it out?

@iam5085 Жыл бұрын

Flux?

@schr3ck3 Жыл бұрын

What are you using there to get of the old fuse?

@TechDayEveryDay Жыл бұрын

I'm using hot air.

@schr3ck3 Жыл бұрын

@@TechDayEveryDay with what device? And what is the liquid? And isn't there some danger because of the hot air and the parts close to the fuse which should not get broken?

@TechDayEveryDay Жыл бұрын

@schr3ck3 please check link from below www.google.com/amp/s/www.instructables.com/SMD-SOLDERING-101-USING-HOT-PLATE-HOT-AIR-BLOWER-S/%3famp_page=true

@Akerfeldtfan Жыл бұрын

Unfortunately that didn't fix it. will keep looking!

@kabassa 11 ай бұрын

I changed the whole motherboard and that didn't solve my problem, so i changed the charging base and then yes that was definitely solved

@Henrik229 Жыл бұрын

Hi I also have a error 13 problem with my robot. But mine charges. Once the robot is charged and i try to start it it just turns off. Once it restarts it starts to charge again. I tried a known good battery but the problem still prevailed. I also jumped the fuse on the Mainboard but it did not held. What could I try now?

@samashraf4587 Жыл бұрын

i have the same problem. have u solved ur problem?