TORQUE SETTINGS FOR GY6 ENGINE ASSEMBLY 5:12 - 10NM / 7.4 FT-LB / 88.5 IN-LB 5:35 - 5NM / 3.7 FT-LB / 44.2 IN-LB 7:17 - 40NM / 29.5 FT-LB / 354 IN-LB 8:05 - 7NM / 5.2 FT-LB / 62 IN-LB 8:29 - 15NM / 11.1 FT-LB / 132.8 IN-LB 9:20 - 6NM / 4.4 FT-LB / 53.1 IN-LB 9:22 - 5NM / 3.7 FT-LB / 44.2 IN-LB 9:54 - 40NM / 29.5 FT-LB / 354 IN-LB 10:30 - 5NM / 3.7 FT-LB / 44.2 IN-LB 11:25 - 9NM / 6.6 FT-LB / 79.6 IN-LB 11:41 - 9NM / 6.6 FT-LB / 79.6 IN-LB 19:04 - 18.3NM / 13.5 FT-LB / 162 IN-LB 20:02 - 9.4NM / 7 FT-LB / 83.2 IN-LB 20:17 - 9.4NM / 7 FT-LB / 83.2 IN-LB 21:06 - 5NM / 3.7 FT-LB / 44.2 IN-LB SOURCE: "GY6 General Torque Settings" Rolling Wrench article (www.rollingwrenchdenver.com/blogs/news/gy6-torque-settings), personal experience, and cross-referencing with professional scooter mechanics

The sounds of parts mating and torque clicking was so peaceful. I very much enjoyed the non-verbal. Thank you!

Loved the video, no music and no talking, marvellous

You needed some more details about the gap between the piston rings and etc, but so far I love the video this would help a lot of kids rebuild their scooters, cheers!

This is a great tutorial , it has helped me out and finished my rebuilt... thank you for the video share...

SO BEAUTIFUL AND PROFESSIONAL VEDIO ! THANK YOU !

Such a neat video! It's therapeutic! Subbed and liked! Really appreciated that you didn't put any silly music carpet over the assembly. I wish I had a mechanic that I could pay to work on my machine that way :).

Life long mechanic on scooters jet skis and motorcycles. I gave ya a sub. Nice videos brother.

This is the best guide in gy6 scooter

Thank you buddy,you are the ONLY person online I take advice from…I’m swapping a 50cc dong fang with a 150 and would like some adiboce

the cylinder and the head are good quality .. good job sir ❤

That was a good video. I appreciate the internal combustion engine more than I did an hour ago.

Rebuilt B&S engines at 12 years old. Folks everywhere had one that did not run great. So few parts. Replaced my head on a GY6 as the muffler bolt holes stripped out due to vibration. Will replace cam with an A11 as I live in the mountains. I replaced my stock CDI as I was told it was limited to 35mph...bought a tunable one. Hits 55+ no problem and about 30 up hill. But she does not get anywhere near the 90 mpg suggested. More like 50 but all these hills eat gas...The last hill up to the house is nearly 2 miles. 9 miles round trip down to the hot springs. Takes like 15 minutes as I don't go fast on those twisty roads. But I get there and back on $.80 or less.

CONGRATULATIONS..YOU ARE A MASTER..I LIKE SO MUCH YPUR VIDEOS..

I’m from Nigeria. Man you way better than my practical teacher ✅ I wanna learn from you master🧎

Awesome vid man! Thanks!

Brawo perfect video çok güzel usta iyi usta aferin eline sağlık. My Turkey

szpilki mają być odwrotnie 11:36 ;) mostek klawiatura ma mieć te pogrubienia które trzyma w ustalonej pozycji trzpienie klawiatury :D

Really enjoyed watch that

Between all the same videos,this is the best!

Fantastic video your video are the best 👍🏻🤙🏻😁

I'm flabbergasted...this video was AMAZING!!! I love how your soo detailed in every speck of the way... You need to build "ALL" bikes in the world...if you did, I know mine would ride too good. Right now my bluescootnboogie is broke down, her owner didn't do soo great on the upkeep nor knew how to... I love your videos...keep them coming. Thank you

Nice job man now I can say I can do it like that thanks

You the best dude 🙏🏻

Outstanding Video.....

Sooper beautiful. Respect.

👏👏👏great video sir!

Great video, very detailed. One thing that could help more beginners like myself is if you could put some details in the closed captions for what your doing in that scene. Things like Torque specs as your tightening each bolt, which grease/oil your using (red vs clear vs blue...or was that thread locker), what the writing on the piston was for, etc... But overall, awesome job. Thanks for posting this type of stuff, it's helping me out a ton!

HOW CAN I NOT LIKE THIS VIDEO. VERY COOL. TEXAS.

شكرا لقد ساعدني هذا الفيديو كثيرا

Amazing video. Thanks for taking the time to do a step by step.

Brooooo i love you ,you save ma life ❤❤

Hi, one question about that starter clutch washer. Its look from video that outer diameter is larger than on stock gy6 washer. On mine, I can slide big gear over the washer and nut. Someone said thats normal. Is it ?

Do you know when your 20mm carb and 26mm exhaust for the Honda GET be back in stock? I’m waiting to upgrade my Metropolitan until I can run your recommended setup

Really good myguy keep on wrenchin

really like the video

What size is the spanner wrench and how many teeth on the crank run the chain for the cam? I see 16-17 or 22. I filled the engine oil and forgot the dipstick so something seized. Hopefully the piston as I have the 150 rebore kit.

Do you do any work with the cn250? I got one in a box and had some questions on what I should be looking for in terms of timing. Most of it is back together but I'm questioning the timing chains looseness and the gears on the rank shaft were not on it when I got it and appear to need to be pressed on, and/or frozen heated and pressed on. Do you have experience when these gears are off and is it possible to easily get them back on? Will timing be off?

Thanks very much that was really good

Very Nice Job. Thank U.

I have a 125cc 1P52QMI gy6 motor (efi) but cant find any upgrades, would love to stick a big bore kit on but i think its the ecu that cant be altered thats stopping it is this the case?

Am realy joy and satisfied... 😁👍

Thanks for that very well done and very helpful video mate! Save me a lot of time fiddling some pieces out. For sure you got a like!

eso si, como armar un scooter. muy fino su tutorial, gracias por tan gran aporte....exictos...saludos...

Thank you for this video. What valve clearance did you use?

Very nice work man love what you do makes me want to open a shop where I'm located

Hello sir i have a 150cc gy6 automatic foward and reverse after roll over the bike now gets gas in the crankcase i changed out carb but still the same thing any tips on how to fix the problem thank you great vid

Cool and its fun..have a great day God bless

Hey, so I know it’s been a year but my wife just bought this lambretta uno150. The guy said it ran 3 weeks ago and it just quit. I checked for spark and it was good but oil would come out from the exhaust valve so I figured rings are bad. I pull the head and notice valve marks on the piston head. So I pull the cylinder and the piston falls off in my hand. So I’m thinking rebuild kit and I look on eBay and I see some but everything I see is 2 valve and I have a 4 valve. And I can’t find a 4valve except for kits that are $400 and up. My question is would you recommend just getting a gasket set and a new piston and cylinder and try and reuse the old head? I’m afraid it is warped but I can’t see from just eyeballing it with a ruler. And the closes scooter shop is like 3 hours away from me. I have also signed up for a couple of scooter forums but I haven’t had a single reply for help. Anyway any advice would be greatly appreciated.

I have a quick question I am rebuilding a gy6 is a qmj but I ordered a rebuild kit for it and the head they sent is shorter than the original and also my studs were longer so I ordered new studs and a new timing chain and cam shaft with timing gear but after looking at I the new cam shaft and gear are actually bigger so I'm thinking I might not have to change the timing chain does anyone know

Hi R.W. I have rebuild CVT Transmission on Piaggio mp3 I changes every thing out & put in Dr. pulley sider 13 gram & new variator kit & I rebuilt clutch put all new seal & spring!

Uno de los mejores arme de motor scooter que he visto...🎉❤❤❤nice

Question I see there's a plastic around the block & cyl head for cooling from that fan that goes on the crank, can I ride with out all this plastic covers and use the natural wind ?

Love you bro❤️❤️❤️💕

Does the back stage pass can access for all the details special the right lbs for all the bolts?

Damn. Very good video !!

Terbaik, from Malaysia

Professional..I wish I could be where you are and learn from you..

Greetings, from Venezuela your video is very good, you will have the torque table that the screws carry, it is to know what torque each screw has, sorry if my English is bad because I use the translator, thanks in advance if you have the workshop manual it would be good thank you

Do you know where the external oil cooler with screw-on filter is mounted on a American Sportsworks Carbide? Bought a basket case and putting back together...GY6 150CC

Love the videos, I learned a lot from watching them and been able to fix most issues with my scooter... I did run into trouble with a 150cc GY6 scooter that keeps getting hot after about 15mins running, I tried everything and the only thing that keeps it from running hot is to "run it" without the belt for testing. Could it be a bent rod? replaced lots of parts..lots.

Great! Thank's!

thanks

I have the Kandi Spyder 150 engine, but, the automatic gear is not picking, any solutions from anywhere?

Looks very similar to my sons kfx50, thanks

Thanks

exellent!

What is the right side crank bolts torqued to after you put the oil pump and everything in ?

good work

I also need, what you explained at the beginning of this video, as pertaining to specs for the rebuild, please. I didn't hit the button but, I did subscribe. Lol.

I tried to put the engine side cover on that the stater bolts to and when I go to tighten it down I can’t move the crankshaft. What would cause it?

Good job I believe I can handle that myself

goood Job.

Hello i have a question for you i have 150cc gy6 and it started smoking from the muffler so i replaced the top end but its still smocking could you tell me why pleas and thank you

thank you so much for not putting some garbage stock music

gdzie znajde serwisówke do tego silnika >?

How did you get the chain in the crankshaft

Is that black RTV silicone your using ?

Tank you

I have a GY6 168.9 cc would I benefit from your gear up kit

I just traded for yerfdog spiderbox 150cc gyc adult 1 seater and was caught on fire so the guy had new wiring harness n says new ring n piston. Have completely about lost my mind past few weeks going over everything got it all set up looked over n now compression, Spark, and Gas but while cranking not even trying to hit like when cranking over the guy had it 180 out on timing come to find out lol back together now hits some but just won't fire all way to start n run not even a half start. Valve adjustment maybe?

Can you do a video on how to charge out the brake and shoes on 49cc Honda ruckus?

Nice to see a GY6 build by someone who understands how to put a motor together. Some of the YT videos of these builds are headshaking in how not to do it. Impact gun on the crank nut for example. Great job on educating people how to do it properly. Have to say the castings of those pieces look pretty cheap and low quality though. No way that motor will have the reliability of a Honda. I'll stick with the GET when the day comes.

the vedio is good i need to ask you can put mallossi to gy6

Do you a write up on the torque specs?

what is the ring gap spec on a gy6 motor

I work for the Navy on nuclear power plants (both aircraft carrier and submarine.) The gloves that I use to keep radioactive contamination off of my hands are EXACTLY the same color as the ones in this video. Freaked me out a little bit.

What's the right valve adjustment for this? Which feeler gauge? Trying to order a feeler gauge kit but want to make sure i get the right size one

Will this video apply for the 2012 genuine buddy 170i as well?

Merhaba seni Türkiye den takip ediyorum ve çalışmaların muhteşem rica etsem videolara alt yazı da ekleyebilirmisin? 😎

Hey I would like to know what type of gasket maker you used to seal the case up

Does anybody know what gy6 motor is in a 2015 sym symply 50cc? Live in a hilly area and doesn't have enough pull to get uphill, so considering a 72cc kit. Thanks.

sir pls make a video of rusi rfi175 im a big fan sir.. cant wait to see on your next video

superbe tuto

Salut cit trebuie regulată admisia și evacuarea la un scuter de 50 cc în 4 Timpi marca first bike rapid?

9:54 what is the caliber for the magnet nut?

What type of socket was that at 7 minutes

How much to build a gy6 short case hi performance 150 cc engine for a ice bear maddog trike

Holy shit. What a skilled mechanic you are I bet you can do that blindfolded

i spilled a soda on my bike while riding i think it got into the engine or whatever spins because i forgot to clean it the next day i tried starting it up and it’s like something is sticky but i don’t know where to start.. i tried using soapy water and cleaning off the dried up soda and let it dry over night im about to go downstairs and see if it’ll start now.. when i turn it on it it makes a sluggish noise as if something is sticky i just don’t know what it is