Please explain how the handmade port is made and how it is connected to the laptop. the map and codes and colors?
@PSICompanyPerformance3 ай бұрын
its just a obd plug that i got from the scrap yard and connect to the obd on the abrites. you just need to 12v+ with a switch, 12v- and kline in this ecu and you can find the ecu pin out on google. its really easy and im sure you will get it done in no time. good luck
@raxar1234563 ай бұрын
Thanks. I will reach out again for questions.
@nikolaosmnk2 жыл бұрын
Great video, can it read eeprom by obd? Make a video virgin Marelli 4AF
@PSICompanyPerformance2 жыл бұрын
Thanks for watching.. I think if you have abrites its possible.
@PSICompanyPerformance2 жыл бұрын
I will my friend as soon as i get one here in the shop
@vincenzomiceli41872 жыл бұрын
Come fare collegamenti ant e post e alimentatore
@sgauto60132 жыл бұрын
Great job. What should be the correct values ? Thanks
@PSICompanyPerformance2 жыл бұрын
Thanks for watching. In the video from 4 min 30 sec i show the diferences that need to be edited... First file on top is the original and the second file on the bottom is the virgin...the highlighted in red are the diferences...pretty much in those locations just edit the bites to ff...
@hayalteknikoto Жыл бұрын
Is there a schematic on how to make this cable?
@jcsilva.26 Жыл бұрын
Did you get the schematic??
@raxar1234564 ай бұрын
and what is the version of software you are using
@PSICompanyPerformance3 ай бұрын
thanks for watching in this case i was using a 2014 version
@182mcg1 Жыл бұрын
I have quick question I wil adopted this ecu for motorcycle but need to settings rev limit over 14000rpm.it is possible to do?
@PSICompanyPerformance Жыл бұрын
thanks for watching yes i now that these ecus were used in ducati and theres is a software that converts these in to auto or moto applications, if you need only to adjust the rev limiter you can use winols or ecm titanium or other chiptunning softwares to do that. good luck
@CT0KAH2 жыл бұрын
👍🏼🔥👍🏼 💪🏼🧠👉🏻💶
@hotice31812 жыл бұрын
Hi dear friend Thank you very much for this video I have 2 queations 1.When it says ignition off did you remove power totally???? 2..After you make it virgin did you follow any steps in car to run engine?? Thank you
@PSICompanyPerformance2 жыл бұрын
Thanks for watching. Yes i remove the power totally.. After i put it to the car it starts right up and then hit the throttle 3 times up to 5000 rpm for the ecu to learn the limits...otherwise the mil light will keep.flashing until the limits are learned.
@davidbc72092 жыл бұрын
Which Is the versión of fvdi?
@PSICompanyPerformance2 жыл бұрын
Thanks for watching. The version used in the video is the 2018 version
@morenokosta Жыл бұрын
molto interessante... E possibile sapere in nome del software che utilizzi per modificare il file della centralina e quale hardware mi consigli per leggere e scrivere la centralina motore? Grazie mille
@PSICompanyPerformance Жыл бұрын
Thanks for watching. I use Abrites to read and to edit the dump and also to write the dump back to the ECU.
@morenokosta Жыл бұрын
@@PSICompanyPerformance grazie mille per l'informazione... Sto guardando alcuni dei tuoi video e devo dire che sei veramente bravo
@PSICompanyPerformance Жыл бұрын
@@morenokosta thank you very much.
@manuelegargano44132 жыл бұрын
Hi, Is there a software for control units 5AM?? Tanks!!
@PSICompanyPerformance2 жыл бұрын
thanks for watching there is my friend, but because of the way those ecus are built, you need something like Abrites to be able to read it and write it, also abrites will virginize that ecu or clone it, depending on what you need. Good luck
@vincenzomiceli41872 жыл бұрын
Salve nel collegamento vedo un ground in più a cosa serve, per alimentatore 12v
@PSICompanyPerformance2 жыл бұрын
Thanks for watching my friend I am sorry but cant understand your question