Very cool project. I have never seen nor even heard of hole spotters. Nice. Very informative video. Thank you for sharing!
@RPMechanics3 жыл бұрын
Thanks for watching Eddie!
@CaptainSwoop5 жыл бұрын
Well done mate! Nice job and helpful vid. Thanks for taking the time.
@RPMechanics5 жыл бұрын
Thanks for watching.
@RyanWeishalla8 жыл бұрын
I was looking at a similar design for the plug to help center. I may look at mounting the chuck directly to the t-slots instead of the back plate, but we'll see when I look at it all again.
@RPMechanics8 жыл бұрын
+ILGopher I still need to center drill the pin on top so I can use it to align the rotary table under the mill spindle.
@miguelcastaneda72368 жыл бұрын
sweet and simple idea thanks for video..noticed a post in need a of a rotary table my route slowly check the home shop machinist jan/feb 2001 edition...the poor mans rotary table build your own.. keep up the videos
@RPMechanics8 жыл бұрын
Thanks a lot.
@dreamsteam82723 жыл бұрын
Exactly what i have searching for....
@mibooth18527 жыл бұрын
another great video, nice idea !
@RickRose8 жыл бұрын
Very cool--Always learn from your videos. Thanks!
@RPMechanics8 жыл бұрын
+Rick Rose Thanks for taking a look!
@eviltwinx8 жыл бұрын
Another great video! Man, I got to get my lathe up and running soon.
@RPMechanics8 жыл бұрын
+eviltwinx Thanks Eviltwin, having a lot of fun with mine!
@jster19638 жыл бұрын
Great work as usual! Keep 'em coming.....
@RPMechanics8 жыл бұрын
+jster1963 Thanks Jster! I hope to.
@kennethkustren93815 жыл бұрын
A centerpunch before the compass ... woulda inspired me to continue watching.
@RPMechanics5 жыл бұрын
Lol
@gvet472 жыл бұрын
I need to make the plate for my rotary table and chuck. Thought maybe you would have faced the face when you were turning the plate round. I need to find a piece of aluminum or cast iron to do this though.
@RPMechanics2 жыл бұрын
I probably should have faced the mount.
@WRFUSINAGENS5 жыл бұрын
Parabens pelo trabalho amigo, ficou muito bom.
@ericbrackenbury2 жыл бұрын
I see the nuts in the back of the plate holding the chuck but you did not show how you fitted the two together. Can you explain that part please.
@RPMechanics2 жыл бұрын
I counterbored the 4 holes with an endmill and just bolted them together.
@andrewdolinskiatcarpathian2 жыл бұрын
Excellent 👏👏👍😀
@BisonWorkshop8 жыл бұрын
as always great job. i need to get me a rotery table and a milling machine. i have tried to sell both my guns to get a mill but no luck. i have been looking at the grizzly g0758
@RPMechanics8 жыл бұрын
+Bison Workshop Thanks Bob. I like the 758. Decent sized table with a lot of features.
@5005ginger6 жыл бұрын
Great job!
@RPMechanics6 жыл бұрын
Thanks a lot.
@petervance98866 жыл бұрын
I just got it -you got a 4 jaw chuck rotary table sandwich.you mill is a 4jaw chuck.
@McFingal8 жыл бұрын
Nice work.
@RPMechanics8 жыл бұрын
+The Texas Gun Guy Thanks, I appreciate you taking a look.
@Ant-master138 жыл бұрын
Great! Thanks for sharing!
@RPMechanics8 жыл бұрын
+Ant-master Thanks for taking a look.
@peterw86907 жыл бұрын
nice work
@RPMechanics7 жыл бұрын
Thank you.
@jamiebuckley17697 жыл бұрын
good job thx 4 sharing.
@RPMechanics7 жыл бұрын
Thanks.
@chicagolathe-shopmaster-sh16807 жыл бұрын
Simpler method- drill through the 4 mounting holes from the back to the front with a 1/4 drill- go to front and counter bore the 4 holes for 1/4 socket head cap screws. Put a morse 2 center in the rotary table and center your chuck on it. Transfer punch through the 4 holes into the table and drill and tap for your 1/4 bolts. Bolt your chuck directly to the table- done in 15 minutes no machining, no adapter, just 4 bolts.
@gvet472 жыл бұрын
He did not have a Morse taper in the center of his rotary table.
@oldschool19932 жыл бұрын
@@gvet47 I've never seen a rotary table without a Morse taper center hole, but even if it has a straight hole- find a pin to fit and do the same procedure-
@gvet472 жыл бұрын
@@oldschool1993 Well his video told bis story on the rotary table center hole is all I was trying to say. I just wish could fine a low profile chuck to adapt since so many have a lot of wasted depth. My table is #2 taper though as wanted to make sure when I got it.
@user-jr8ol2yg4t8 жыл бұрын
Hello. 5:48 Please tell me the name of this measuring instrument . Thank you
@RPMechanics8 жыл бұрын
+Михаил П That's a small hole gauge.
@bikingmnviking38018 жыл бұрын
Subbed, I need to learn more metalworking.
@RPMechanics8 жыл бұрын
Thanks a lot.
@bikingmnviking38018 жыл бұрын
No metal lathe here but I see those 4 jawers are cheap and I have a great drill press from like WWII that could probably benefit from that exact upgrade. I think we're at close levels of learning so as you grow, learn, and share I will benefit and maybe be able to understand some of the biggies here on YT. Ablom...etc
@petervance98866 жыл бұрын
Why would you want a four jaw chuck on a rotary table?