Ive only had a little squirt on the bike so far but first thoughts are 👌

Silly billy! Glad you listened this time 🤗

Yes would be an interesting test, I do recall having a slight issue before fitting the booster plug when I just had the rear cans I think. Cut out like they do when lean. I had a crf that was terrible until I’d fitted a fuel programmer.

Hi Mate, They sound very very good….to my ears… not sure the neighbours or MOT man will agree though. Think I will have to make some baffles for the exhausts now, don’t want to be too antisocial!! Re the Gaskets, TEC advise to fit the new ones on top of old as they are so well seated so that is what I have done. Cheers

They are a bit loud, I'm surprised that they advise you to leave the old gaskets in. The new washers are exactly the same as the one's fitted at the factory. I removed the old washers.

I'm thinking about buying some of the baffle wrap and adding an extra layer. That'll tone it down a bit.

Hi Colin, yea I’ve got the booster plug on did it with the filter, primarily for that reason.

bikes are already to lean from the factory to meet emissions, fit a powertronics fuel controller and you'll realize just how lean it was.

Need a compare vid!

I had a slight issue with the right mount at the bottom. Just had to tweak mine a bit to bring it more upright so the bolt lined up nicely. Nothing major though, have another look not worth sending back if yours the same.

@@DormanDiaries I was able to get the OEM silencers on yesterday afternoon. This morning I got the Tec silencer on the left side with some fussing. Ar this point I was determined to get the right side on. I got it, but it was far more 'square peg in a round hole' than I was comfortable with. Nothing appears to be damaged, so I guess all's well that ends well.

@@markfortin8286 Nice one, glad you got there eventually!

​@@markfortin8286what problems have you had with the bike?

@@relevation0The two big problems I had were a fork seal that failed almost immediately (I think it was 600 miles from new), and the terrible battery they equipped it with. If it dipped below 5 degrees celsius over night, more often than not the bike would not start. Even if it had been on a battery tender. Sometimes I could get it going by putting a space heater blowing on it for a few hours. I was not impressed with Royal Enfield North America, as they had apparently not imported any spare parts. Those of us that were early adopters of the bike back in 2019 were pretty much on our own. At least in my region of the country. I called all the dealers that were within 250 miles of me, and none of them had parts. The three year warranty was more theoretical than practical. I was able to get the front brake recall taken care of, but even that took a few months of being on a waiting list at the dealer. Make of all that what you will!

I’m not sure you will find the wrap will make much difference it didn’t on Kjs single can, enfields may be different. I had to weld a washer in to hers inside the end cap to make a difference.

I'm going to wait and see what you do with your silencer's. As a temporary measure I'm putting the standard silencer's onto my stainless steel header pipes. That'll keep me going until I save up for some of those Canon silencer's.

@@paulstoker7650 - I’ve welded some washers in end of mine this weekend. They don’t look as good as the nice big holes 🕳 🕳 but they do the job, you can now ride through villages without getting angry looks from all the locals. I took the end caps off pit them pointy end down, hit the inside of the hole rim in 3 places with a small cold chisel and sit the washer in with another below to make it rebate and tack welded in 3 places. Looks neat as can’t see any weld from the outside.

I've fitted the original silencer's back on for now. I'm going to get a washer welded in the way you've done it. Thanks for the update and suggestion. Take care and stay safe.

@@paulstoker7650 Ive put a photo up for you showing the modified cans. Go to the community tab on our channel and its there for ya. 👍

Looking forward to the results (including economy & performance)😉

I hear what you’re saying about the fins but likewise I don’t like artificial things, I suppose they may have added a bit of cooling but probably very negligible.

It's just a tiny, small thing i'll miss and the advantages of fitting this new set FAR FAR FAR outweighs the fins missing

Only women drink wine,Yorkshire men drink beer.

@@stevepalmer5670 - I’ve shared a bottle of white with Mrs D tonight 🤣 admittedly both of us usually drink pints! 🍻

Hi mate, not intending to, I’ve got a booster plug, hopefully that’s sufficient to stop any lean issues. May have to revisit if I get any lean signs. Not chasing power, I got these more for the stainless and lightness.

Asked the dealer I bought the bike off and he said not so ! 👍

@@themoog3889 well ok if he said so but ask arround because 5 peoples did the same here 😊 & they kiss the warrenty gudby 👍

Mines over 2 year old now so not a consideration. Weren’t bothered day one either though 😂🤣😂

@@DormanDiaries isn't it a 3 year warranty ???

@@themoog3889 yea probably, not really a concern for me. If it breaks now it’s probably my fault anyway!