Run smart phone without battery with external power source

Рет қаралды 46,254

3 жыл бұрын

In this video we will see how to power on old dead battery smart phone with external power source like 18650 battery. Wach untill end. Thankyou...

Пікірлер: 31

@Alhussainba 2 жыл бұрын

Well done, clean and elegant. Was surprised seeing a Lumia, I have my Lumia 950xl on my table bare back, the motherboard is probably dead as it sunk at some point, but I wanted to learn how the wiring works so that the phone requires the battery to work. Unfortunately, I couldn't replicate it with my Poco f1 as the battery doesn't have a + and - pins, it has an FPC connector and I don't know how to deal with it.

@abidurrahmanchowdhury4412 2 жыл бұрын

A bit late here. Have you tried detaching the BMS from your OEM battery so that you don't have to deal with the whole FPC connector mess? The battery pack along with it's protection board solders to OEM battery BMS which then connects to phone via FPC connectors.

@umargul5644 3 жыл бұрын

Well done sir, thanks a lot

@leonbishop7404 7 ай бұрын

this is very useful because you dont have to solder anything directly to the phone and still can use battery when needed

@inamulhoque2627 3 жыл бұрын

Nice idea. Thanks.

@mkcaplayz6978 3 жыл бұрын

You: Infinity% Me: 100

@zodiacfml 9 ай бұрын

thanks!!!

@johnjacobs3673 3 жыл бұрын

I try this and it worked .i use a zte battery to power a samsung galaxy j3 and it turned on however when i try to chargwe it it saids the batery is not compatible how can i fix the charging problem. Do you think it has to do with the bsi and btem wires not connected??? Please help me

@marketersourav 2 жыл бұрын

u have to charge your battery externally

@urbantamizh5363 3 жыл бұрын

When I tried directly with usb cable to phones input battery terminal it starts up phone and after 3 seconds screen goes off...why it happens

@tgmtf5963 2 жыл бұрын

Too much power

@SiddharthHaobijam 2 жыл бұрын

if it is samsung higher end phone it could be becos u have to take account the pin next to the phones input battery terminal . it seems to send signal to the phone that it is not connected. i tried directly connecting 3.something volt to the input battery terminal but it starts up n shuts down soon

@markjarvillemartin4228 Жыл бұрын

Take the BMS board. It probably has 3 to 5 wires connection to the main board of your phone. Use the original BMS board, and solder your external battery on it

@mathematicsclassesbyrkshar8993 2 жыл бұрын

Lumia 535 mere pas bhi hai purana

@sunmugarasa1319 2 жыл бұрын

More smart mobile hacks

@prentisboy2019 2 жыл бұрын

I got some questions

@expression3639 11 ай бұрын

lol it's not "without battery" if you solder battery cells to it.

@shahidhossain4227 3 жыл бұрын

are you recording in night???? na???

@febriansyah4392 3 жыл бұрын

What part you use?? Please explain 🙏

@World_Point Жыл бұрын

only 18650 battery buy from Market

@claudiofiero8523 3 жыл бұрын

Can you give us some more explanations about where does this battery pack comes from/ how you did it

@danthegreat7590 3 жыл бұрын

Well i know that if you have a battery of the same voltage it can be any kind of rechargable battery what i think hes doing here is wiring it directly to the positive and negative pins of the phone as long as its the right voltage it should theoretically work

@sweetpotato7993 2 жыл бұрын

@@danthegreat7590 But how would you charge this battery? I think he did not show that bit.