@23:55 Look at a direct size comparison of the S550 *base* GT calipers to those on the *base* GT S197!
@Smasher-Devourer21 күн бұрын
Picked up a pair of these calipers from thepartsfarm for $80 shipped. Found rotors on rockauto for about $50/ea. Can't wait to upgrade the brakes on my 2005 coyote swap. The original brakes just aren't cutting it.
@powercordz6 ай бұрын
Thank you so much for sharing your progress on this! I'll have to do the same upgrade
@CarolinaLaserWorks9 ай бұрын
Great video!
@OctaneSlain9 ай бұрын
Thanks man, I appreciate it a lot! 💯
@allancooper38659 ай бұрын
Bravo 👏 thank you for sharing your work, do you have to bleed the new front 4 piston calipers any different than the one’s you replaced, cause I herd that there is 2 bleeder valves per caliper (a left and a right or one bleeder valve on the outside of the caliper and one on the inside of the caliper…. But I might be mixing up the 6 piston calipers bleeder valves , but I think it would work by bleeding the furthest valve first , which is the outside valve then the inside valve (the valve closest to the brake pedal ) last , thx again for uploading, cheers 🍻 can’t wait to see more mustang content from your channel soon, good work man!!!
@OctaneSlain9 ай бұрын
I started with the inside bleeder and then the outside. But going from the outside in would probably be better!
@BryanDominguez-x4z3 күн бұрын
Do you know if s550 rotors will fit? They are also 14 inch they came with the calipers I bought was just wondering if I could use them instead of buying new rotors?
@OctaneSlain2 күн бұрын
No, I had a set of S550 rotors given to me. The vent setup is completely different and the lug holes are slightly wider
@Budgetracinggarage9 ай бұрын
Well I see you put a filter on the v3 pro charger
@OctaneSlain9 ай бұрын
Yea I finally found one that works, still had to smoosh it down a little bit lol
@Sigmaa5.0h6 күн бұрын
Does The S550 Calipers Fit With The Stock 2011-14 Rotors
@OctaneSlain5 күн бұрын
No
@kelvinlantigua54694 ай бұрын
I thought you only needed a washer if you use a S550 rotor and not a GT500 14” rotor
@OctaneSlain4 ай бұрын
You have to use the washers to center the rotor for the 14" Boss/GT500 rotors. I don't think you can use S550 rotors. When I bought my used s550 calipers, he also gave me the rotors too... And the venting is completely different and the lug stud holes are slightly larger
@Axel.3v6 ай бұрын
Why’d you have to replace the brake lines
@OctaneSlain6 ай бұрын
I wanted a squared fitting brake line that fit the S550 caliper perfectly. The factory one is rounded. Im not sure if you can re-use the factory lines or not, but I decided to upgrade them just in case and be on the safe side.
@Axel.3v6 ай бұрын
@@OctaneSlain I’m planning to put a set of these on my 07 s197 and trying do it on a budget so I hope I could use the stock ones, if I do end up using them I’ll let you know!
@atleyg.51766 ай бұрын
Do the stock lines work? Im also curious, I ordered rotors but hesitant on lines at the moment.@@Axel.3v