Video is overall pretty good and as someone that has the rebranded version of this case (the Tecware Fusion) it's nice to see other people's build experiences and seeing the limits and versatility of this case. Looking at the offset holes on the top and bottom brackets are a nice touch.

THANK YOU! After hours spent on reddit and on sites ti check the SAMA specifications, this is what I needed!

I recently “boot”(bought) 😊 Canadians sound way too cute. Couldn’t take a gangster from there seriously

Many thanks for the video. I own an m-atx board and an atx psu and I was ready to pull the trigger for this case but now I see that it is very narrow and in practice is only good with m-itx board + SFX PSU.

Wow thanks for you wisdom, it'll sure spare me some headaches !

Thanks for mentioning about the GPU length, you've saved me lots of bucks

This is the case I use. I managed to fit a massive GPU in it (3.5 slots wide, 331mm long), though I had to maneuver the GPU into position before even adding the motherboard. I'm using an ITX motherboard with an SFX power supply, which also allowed me to fit a side-mounted 280mm AIO liquid cooler. I also have slim 120mm fans mounted inside the top and bottom panels to maximize airflow. It runs well and the thermals are good.

Great video

Thanks for this vid!

Thank you for the video, really good explains possible problems. Could you please tell, is there any chance it can fit 158 mm cpu cooler?

When you refer to adding an SSD at the top backet at around 4:30, from the indicators printed am I expecting that a 2.5 inch SATA SSD would be mounted at the corner horizontally with three screws only? Because if I try to place the SSD vertically at the center the bottom holes of the SSD do not reach the bottom holes of the bracket to be screwed on at all. Also I must say that mixing and matching PSU cables is not ideal at all even if it's same manufacturer due to lack of standardization of some aspects of PSUs so it's good advice on the video at least to mention requesting for replacement. Looking for PSU extension cables confirmed compatible with your chosen PSU is also an alternative.

No sound at 4:44

I have an mATX with a 170mm long ATX Modular power supply , while my GPU is 242mm long with 2 fans and just one 8 pin connector required. Can I fit everything in this case? Also, what if I use 80mm fans on the bottom instead of 120? BTW thank you so much for this video!

Can I use a MicroATX motherboard, a graphics card about 322mm long and use a SFX-L POWER SUPPLY? I found ROG Loki SFX-L 850W Platinum which dimensions are: 125 x 125 x 63.5 mm

To solve the short cpu cable issue I just ran it behind the motherboard

Any update 10 months later with any new info? I'm about to buy one of these 🤭

Hi there! :) I dunno if ur version is with the glass panel or metal. Anyhow, if it's the glass version, do you know if it's possible to swap the side panels?

This is the vid I wish had come out before I did my build. I bought a beefy ATX PSU a while back in readiness for these juicy GPUs, but have found myself in a position where I probably can't upgrade unless I choose a 2 fan card because of the PSU cables. I could move the GPU to a (s)lower PCI slot, but my fan config doesn't really allow as my intake is on the bottom of the case

I was wondering do you believe while using an matx motherboard that having slim fans would help with the front panel connector issues

what type of fans are those on the bottom? standard thickness?

Can the bottom intall two 90mm fans instead of 120mm fans?

Thanks i was conflicted wether i should choose this case or the Asus ap201 for my Micro Atx, Atx PSU 160mm build and looks like the asus is the way to go even if its a bit bigger

you can use a modular ATX PSU and no problem

is it possible to put 1 more fan the at top? there's no obstruction?

can i fit a 250mm gpu with an matx psu?

Hi I was wondering if you had to buy a mount for the sfx psu or can you just mount it in the stock case? thank you for your video!

You can use an ATX power supply with a big GPU if the power supply is short enough. I bought this case only to discover my 165 mm long power supply wouldn't fit, but I got a 140 mm long one that does. I've even seen people squeeze a 150 mm PSU in there but the cables press up against the GPU backplate.

Hey there, Is it possible to use an ATX psu with an Matx motherboard?

It IS possible to use the case with mITX, ATX PSU and a long GPU. But you have to mount the PSU directly to the top instead of using the ATX psu bracket.

Man they shouldnt have advertised this as an matx case. While the board can fit, everything else is compromised.