No video

Samsung Top Load Washer - Not Spinning or Stuck on Sense MODE, (FIX)

  Рет қаралды 119,827

Jesus Montoya

Jesus Montoya

Күн бұрын

Samsung Washer not Finishing cycle- Getting Stuck in Sense MODE
The Fix was the Motor Position Sensor. Which detects the Speed of the tub while spinning.
Parts for Repair-👇👇👇
Clutch Assembly with TMR sensor- encompass.com/...
Subscribe to the Channel for more Appliance Repairs and Tips.
If you have further questions leave a comment. Thanks for Watching.

Пікірлер: 340
@hanzischultz9284
@hanzischultz9284 2 жыл бұрын
I have the same model washer. I found one (green) of the three TMR sensor wires was severed. I think it is a design issue. The wires are too thin and it is so easy to be broken with that level of shaking when it's spinning. While I was fixing it I collected some data for testing the three components: Capacitor, Shift actuator, and TMR sensor. Hope it is helpful to those who need it. 1. Run capacitor (1). Capacitance = 45 µF ±5% (2). Check body shape. 2. Shift actuator (1).Ohm range: 1000-1100 Ω. (2) check wire. 3. TMR (tunnel magentoresistance) sensor. There are three wires: green, blue, and red. Using Ohm meter to measure, one should get these: (a) Green-Blue = OL (b) Green-Red = OL (c) Blue-Red = 10 KΩ
@JesseApplianceRepair
@JesseApplianceRepair 2 жыл бұрын
thanks for the info 👌 im pretty sure someone will benefit from it
@6point2000
@6point2000 2 жыл бұрын
@@JesseApplianceRepair Do you have a link to order the TMR ? . i am look and no luck where i can buy it .
@JesseApplianceRepair
@JesseApplianceRepair 2 жыл бұрын
@@6point2000 Samsung doesnt sell the sensor by itself unfortunately. but you can find the link in the description to the full clutch assembly. that includes the sensor. but I recommend to check all wires for any rips before you order any parts.
@capslu6305
@capslu6305 2 жыл бұрын
Where can I buy The TMR Sensor
@TheDerek00
@TheDerek00 Күн бұрын
Thanks for the info
@georgeharvard1417
@georgeharvard1417 7 ай бұрын
I just want to say thank you to KZfaq. And I want to thank you to demand that's doing the work on what he's showing right now. It helps a lot of people just for what you're doing. Thank you so much you help a lot of people thank you
@JesseApplianceRepair
@JesseApplianceRepair 6 ай бұрын
Love helping others. Same as when I first started and others helped me. Thanks for watching Cheers
@JohnMEstrada
@JohnMEstrada Жыл бұрын
It's so hard to find any videos for this specific Samsung washer. Thanks for making this. I am going to try and clean that sensor tonight and see if it helps. Much appreciated!
@alextorres1544
@alextorres1544 2 жыл бұрын
Yes, please keep posting more appliance repair videos! Thanks!
@Jorge-gn7ft
@Jorge-gn7ft 3 ай бұрын
thank you so much , i just got mine up and running again thank to your video you saved me hundred's of dollars .
@javieracosta7860
@javieracosta7860 Жыл бұрын
Good morning technical friend, I have a similar fault in a WA19J3000AW model in the diagnosis the hot led is the one that flashes, I appreciate your collaboration to correct this fault. Greetings from Venezuela
@jaimerivera8051
@jaimerivera8051 28 күн бұрын
Hey man I just want to thank you for this great and detailed video I appreciate you this video has saved me from getting a new washer I was about to go pick one up 😅
@JesseApplianceRepair
@JesseApplianceRepair 7 күн бұрын
Glad I could help
@sellomahlo9034
@sellomahlo9034 Жыл бұрын
Thank you very much for an informative demonstration on how to deal with the sensor in question - well done and keep it up. I am the new subscriber to your programme and intent to be a regular.
@JesseApplianceRepair
@JesseApplianceRepair Жыл бұрын
Thank you so much for the Support, it means alot. I have more content coming out.
@TerriBovitzPollard-qm9ej
@TerriBovitzPollard-qm9ej 4 ай бұрын
So it's my sensor or my capacitor. Those are my two choices on a code of small which is telling me my water hose or pump might be clogged or frozen water which is not the case cuz I'm living in Florida unless you disagree but your video has been very helpful. Thank you so much my brother
@JesseApplianceRepair
@JesseApplianceRepair 4 ай бұрын
Check the filter to make sure there is no dirt on the connections of your hoses
@apolinarrendon7506
@apolinarrendon7506 2 жыл бұрын
Where can i get the first senscor , could you tell me the place you got it from? Thank you also your video helped me a lot
@augustharlacher5660
@augustharlacher5660 7 ай бұрын
I have the same model, and the same problem. It doesn't complete the cycle, switch to rinse and spin and it tries to start but stops on spin. And when it does finally start to spin it doesn't spin that fast and the cloths are still very damp. So, I'll have to look at it again more closely because I just checked the drain hoses they were not clogged. Jesus thanks for a step-by-step explanation. You are the man Bro.
@smiley10261
@smiley10261 6 ай бұрын
Did it work I am having the same problem.
@raymondblakley3731
@raymondblakley3731 5 ай бұрын
@@smiley10261bad sensor problem If your does not spin out
@misterdrummings
@misterdrummings 2 ай бұрын
@@raymondblakley3731 This sounds like the same problem I'm having. The machine gets hung up in spin cycle, and the cycle doesn't complete. The hot and warm LED's are flashing in diagnostic mode, which the manual tells me means either the machine or load is out of balance, but I checked it out and that is not the problem. Do you think I need to replace the sensor?
@raymondblakley3731
@raymondblakley3731 2 ай бұрын
@@misterdrummingswhat the brand if it a Samsung washer top load and you replaced all four shocks then you will need a new spin basket assembly
@mikehikalea2323
@mikehikalea2323 3 жыл бұрын
Great video and excellent teaching for a beginner like myself..👍
@JesseApplianceRepair
@JesseApplianceRepair 3 жыл бұрын
Thank you. More videos coming soon
@davenportchurchofgodbyfait8643
@davenportchurchofgodbyfait8643 2 ай бұрын
very good instructions for troubleshooting. It analyzed my problem, thank you.
@robertrumsby8499
@robertrumsby8499 Жыл бұрын
Thank you so much for the video, does anyone have the part number for just the nylon tmr sensor. Thank you
@electron7373
@electron7373 Жыл бұрын
Top work! Thank you for the repair guide!
@karlahernandezvalles
@karlahernandezvalles 9 ай бұрын
Great video! It is exactly what my Samsung washer has. Do you have any video on how to rewired the sensor? It’s almost impossible to get it here in Mexico 😢
@curtycox689
@curtycox689 Жыл бұрын
Thanks *TEACH. YOUR A EXCELLENT TEACHER.
@jerrydonofrio4154
@jerrydonofrio4154 2 жыл бұрын
Superb instructional with easy to understand explanations and video great as well a audio. I know understand how this newer type machine works.
@christianbattey3186
@christianbattey3186 2 жыл бұрын
Thanks for showing us how to fix the problem 👌🏾
@JesseApplianceRepair
@JesseApplianceRepair 2 жыл бұрын
anytime.. Im glad the video helped you out.
@stso9daa
@stso9daa 2 жыл бұрын
Jesus, you are great! i have been looking for this. it is exa t issues i have. Thank You so much!!!!!!
@JesseApplianceRepair
@JesseApplianceRepair 2 жыл бұрын
Awesome. Im glad the video helped. 👌👍
@jaimetorres4567
@jaimetorres4567 2 жыл бұрын
Ya cambie el sensor y no centrifuga que más puede ser
@leecarnes8923
@leecarnes8923 8 ай бұрын
My washer will not enter diagnostic mode. It doesn't spin, doesn't fill with water, does lock lid. It just makes a weird clicking sound. Any ideas?
@jeffmejia2978
@jeffmejia2978 5 ай бұрын
Mine does the same thing. Did you ever figure out what was wrong with it? Mine just started doing this after two loads this past weekend.
@COVID-xr5mj
@COVID-xr5mj 2 ай бұрын
​@@jeffmejia2978any solutions?
@hkdjbert
@hkdjbert 2 күн бұрын
If the clicking you hear is a constant whirring motor hum and click, it's probably the lid lock mechanism. Take it out and open it up. Inside there will be 2 sets of spring contacts. Clean the heads with some sandpaper and reassemble.
@franknilson180
@franknilson180 10 ай бұрын
I also experienced malfunctions where the machine did not get filled quickly or at all, or that it would not complete the spinning cycle with about eight minutes on the clock remaining. The solutions were easy. The first problem was easy to sort out. I loosened the water inlet hose at the back of the machine and removed the sieve on the inside of the pipe at the inlet point. After I cleaned the sieve and installed it again, the problem of filling was gone. The second problem was just as easy. At the outlet, there is also a filter which can be cleaned. I have found some thin string that wound up and caused the water pump to stop functioning which caused the machine to stop. I just removed the string and the machine runs 100% and I did not have to buy a new water pump, motherboard or electrical spares. Needless to say, I saved plenty of money and did not enrich the scammers who would take your money without blinking twice.
@moezbhaloo1681
@moezbhaloo1681 Жыл бұрын
Thanks got lots of info. Am going yo check a top load samsung not spinning. So will check what you showed
@jasonkruschke2147
@jasonkruschke2147 2 жыл бұрын
Thank you very much for this. I cleaned the sensor and things are working again. Fingers crossed it keeps on keeping’ on.
@JesseApplianceRepair
@JesseApplianceRepair 2 жыл бұрын
Thats awesome. Im im glad the video helped 🤝💪
@minneshbugareth9327
@minneshbugareth9327 Жыл бұрын
Hi Jesus. Great video, thanks. I have Samsung top loader wa13f5s2. The machine fills water but then does not spin to start the wash. There is a sound like the motor wants to start turning, but it doesn’t turn. Please offer some advice. I suspect the motor is faulty. Thank you
@ironmike916
@ironmike916 7 ай бұрын
I’m experiencing this issue right now lol
@antonetterobinson5476
@antonetterobinson5476 6 ай бұрын
Thank you for the video. Can you give where the part can be purchased?
@swishcamp81
@swishcamp81 Жыл бұрын
I Thanx for videos! I was wondering where you got your training because i want to learn Appliance Repairing!
@gregorystevenson2957
@gregorystevenson2957 2 жыл бұрын
Hello, great video. I have a newer model of this washer where I have encountered an agitator/spinning issue. It is not spinning. The washer was loaded with too many bath mats which when wet was heavy, and I am assuming unbalanced. The machine then stopped. After taking everything out and trying to spin the agitator and barrel with my hand, I could hear a light grinding/scraping sound underneath. Could something have come loose in the motor to the barrel/ agitator because of a heavy unbalanced load? Thank you.
@mydogs4657
@mydogs4657 5 ай бұрын
Bearings problem
@Ruben-oh4mj
@Ruben-oh4mj Жыл бұрын
Dude....love the video and explanation. Thanks so much and great job.
@danjones2110
@danjones2110 2 жыл бұрын
Any suggestions for a Samsung top load model wa56h9000ap/a2 that won't spin in normal mode. In service and quick spin modes it spins up to high rpm. In service mode are we bypassing all the sensors? No error codes are displayed. Thanks
@ashleythaeunisen8860
@ashleythaeunisen8860 10 ай бұрын
Thanks for the video I will definitely try out this way on this video thank
@RTTSOLUTIONS1
@RTTSOLUTIONS1 4 сағат бұрын
Hi Jesus. Great video by the way. I am wondering if you can give me your input on a problem with my Samsung model # WA45N3050AWA4 which looks identical to the one you have in the video. After the spinning cycle, the clothes are still wet. I know it's not a clogging or water pump problem because the water goes out the drain tube no problem. It looks like it goes thru 3 rinse and spin cycles. I feel the machine spinning as it should and i just cant figure out why the clothes still come out wet. I even tried a cycle after pushing the spin only button with no luck. Any help will be greatly appreciated.
@quickfixappliance
@quickfixappliance 2 жыл бұрын
First of all, thank you for this detailed video buddy. I have a question and I hope you can answer me. My samsung washer, exactly like the one in this video, after first wash it starts draining for only 2-3 sec and then stops. I know its not pump because It drains on spin easy. I checked wires and everything is good. This is the second samsung washer thats been doing the same thing. So it adds water, agitates, then when its time to do first drain and go rinse after it, it drains only couple of seconds and machine stops completely. I changed actuator and control board. Please help if you can. Keep up the good work
@JesseApplianceRepair
@JesseApplianceRepair 2 жыл бұрын
So ive had a similar issue in the past to what you mentioned. and it was the cables coming from the Computer board to the Pump that were bad. So you mentioned on the other cycle the pump drains. so that seems to be good. so get a multimeter and run the washer when its time to drain check the ports coming from the board to the pump ( the two cable connectors. ) most of those pumps should be 115 volts. Make sure you are getting the full 115-120 volts. If you are getting less the cable is the issue. Let me Know what you find.
@cathinaisaacs2738
@cathinaisaacs2738 3 ай бұрын
Really would appreciate your help, I have the same model machine but the lock light is not coming on and it keep staying in a spinning mode but water is not going in to the machine.
@brucewayne4211
@brucewayne4211 Жыл бұрын
WA40J3000WA washer motor spins continually upon power on. This machine has had an initial problem of unbalance which was cleared by replacing all 4 balancing rods, Capacitor replaced, TMR Sensor replaced, and shift actuator has been replaced. All replaced for multiple issues found caused by the initial unbalance. At the moment there are NO fault codes but the motor runs continuously from power "on" and turns off 5 seconds after power button is pressed. The machine does not go into spin because the motor does not stop/pause to engage the gears and grinds the gears.
@COVID-xr5mj
@COVID-xr5mj 2 ай бұрын
Same
@tdilla3818
@tdilla3818 Жыл бұрын
Question I have the same washer.is it natural for the washer to make clacking sound for a minute going from wash to rinse or like when its changing gears or something....
@user-gb7ev7ok7c
@user-gb7ev7ok7c 6 ай бұрын
Hi my friend I want to thank you for the good video and also just wondering if you have a link where to find that specific sensor I’ve been searching but not luck… can you help me with that
@octaviobanuelos6812
@octaviobanuelos6812 Жыл бұрын
Good afternoon do you know the part number or do you have to buy the hole clutch assembly
@dannyryan5549
@dannyryan5549 10 ай бұрын
Very helpful. Well done..
@JesseApplianceRepair
@JesseApplianceRepair 10 ай бұрын
Glad it was helped.
@royabreu3627
@royabreu3627 Жыл бұрын
Hi my friend i liked your video, very well explanatory, thx for your help
@wilfrednorwood2250
@wilfrednorwood2250 6 ай бұрын
Exactly what I needed thank you.
@jaimetorres4567
@jaimetorres4567 2 жыл бұрын
Excelente sube más tutoriales de refrigeracion en especial samsumg
@derekp77
@derekp77 Жыл бұрын
Can you tell me the part number for the nylon sensor you are replacing in the video..? Many thanks
@cavemanproductions2.015
@cavemanproductions2.015 6 ай бұрын
That's what I want to know!
@peterchand9804
@peterchand9804 10 ай бұрын
Thanks for explaining about the sensor on DC68-03172B-03. What is the part number or name of it and where can I get it? Or then what does that repair cost?
@JesseApplianceRepair
@JesseApplianceRepair 10 ай бұрын
sorry for the delay. the sensor comes with the whole clutch assembly. ive called Samsung but they dont sell that part by itself. Dont know why.
@anthonylancellotti4688
@anthonylancellotti4688 2 ай бұрын
I have the same exact washer with the same problem I don’t know where to find this sensor I need your help please 🙏
@jeffreyparnell4314
@jeffreyparnell4314 2 жыл бұрын
What did you use to clean the gear? Also, is it possible to just clean off the sensor if everything appears intact? If so, what did you use? I appreciate the video. I have this same model and same issue. I’m hoping to fix it myself.
@antoniohernandez2653
@antoniohernandez2653 3 ай бұрын
saludos gracias x la informacion, tengo una lavadora igual que no me llega voltaje a la bomba de drenado ayuda x favor
@riaanlloyd930
@riaanlloyd930 3 ай бұрын
Hi Jesus, I have a problem with a Samsung wobble top loader WA13F that will not spin. I have replaced the drain pump and main pc board as the drain motor does not get power to engage the gearbox to spin. Please advise what could be the problem. Thank you ,Riaan.
@b.aroyalty3071
@b.aroyalty3071 11 ай бұрын
I have the same washer but it spins but sounds rough when it spins. I did the nickel glue quick fix for the handle. what part do I need to replace and where can I order it from
@pedrorosado9534
@pedrorosado9534 2 жыл бұрын
Loved ur vid. Hope I can fix my spin on same samsung washer. You think you can send the links for : sensor, capacitor and actuator. Gonna start w/ the sensor n 🙏
@JesseApplianceRepair
@JesseApplianceRepair 2 жыл бұрын
In the description I have the link to the TMR sensor and clutch assembly. What is your machine doing. ?
@pedrorosado9534
@pedrorosado9534 2 жыл бұрын
@Jesus Montoya it makes sound like its about to start spin, makes bad noise for a few seconds, then stops and starts wash again. Already changed the susoension rods.
@pedrorosado9534
@pedrorosado9534 2 жыл бұрын
I see the link but it is for the whole clutch assembly it is too much money,,, Can't I just buy a sensor?
@jerimiahtanner3031
@jerimiahtanner3031 4 ай бұрын
So ive tried cleaning rhe sensor off and it still wont do anything, but i cant seem to find where to buy a new sensor/accuator, would you happen to have a link? To said parts?
@janettham9055
@janettham9055 2 жыл бұрын
Jesus. Awesome video man. Spot on. Well explained and well shot
@tudor888
@tudor888 2 жыл бұрын
Thanks for posting this video! Someone gave me a similar washer, it didn't spin. I found that the TMR sensor wires were broken so I repaired them. I tried to turn on the spin cycle without hooking it up to water, but it won't spin. Do I need to hook it up to water for it to work?
@JesseApplianceRepair
@JesseApplianceRepair 2 жыл бұрын
Under spin only no. Only if it says rinse and spin then yes. Let me know
@tudor888
@tudor888 2 жыл бұрын
SO, after I left it unplugged for a few hours, I plugged it in and ran the spin cycle. This time it spun the drum, I could see it from under the washer! The water pump was running too but no water came out. I can hear a little bit of water sloshing around in the machine but it's not reaching the pump, because the hose is empty. Is that normal?
@JesseApplianceRepair
@JesseApplianceRepair 2 жыл бұрын
@@tudor888 yup that noise is normal. It does it when theres not enough water to drain. Pump will stay on for a while then goes into high spin then stops for a little bit then it starts draining again.
@tudor888
@tudor888 2 жыл бұрын
Thanks so much for the prompt reply! I'll hook it up to water and test it tomorrow. PS: You're awesome!
@arnellgayo3021
@arnellgayo3021 2 жыл бұрын
Nice.. I'll try these tutorial.
@reneperez8810
@reneperez8810 3 жыл бұрын
Gracias me sirvió mucho este video😀😀😀😀
@JesseApplianceRepair
@JesseApplianceRepair 3 жыл бұрын
Gracias bro. Voy hacer más contenido pronto
@reneperez8810
@reneperez8810 3 жыл бұрын
@@JesseApplianceRepair esta bueno brother👊 .
@PaulByrne-c6j
@PaulByrne-c6j Ай бұрын
How can I get the sensor in the video. I only see it with the clutch assembly all together.
@angelsaucedo4883
@angelsaucedo4883 Жыл бұрын
I have the same exact model and it washes just fine but when it spins it rattles and shakes & doesn’t get the clothes fully rinsed and they all come back out wet
@ulisesmeza2435
@ulisesmeza2435 Жыл бұрын
I have the same exact problem with that same model of washer
@MiguelMartinez-lm1mx
@MiguelMartinez-lm1mx 26 күн бұрын
I have one top load washer samsung that when I start the cycle the only thing that it does it's draining then stops.
@Cbmacdaddy
@Cbmacdaddy 3 жыл бұрын
Great video, thanks!
@shaskiekaduncan5927
@shaskiekaduncan5927 7 күн бұрын
Good day mine is not going on the lock button and each time it’s fill with water and you put in for washing it just let out the water before washing
@paulbudd5687
@paulbudd5687 2 ай бұрын
Okay so I have the same washer as this the one you're doing right there mine spins when you turn it on it won't stop spinning and even when the door open the door is open it won't lock what should I do if it keeps spinning how do I stop it I tried to reset it it won't reset
@wendyrenerodriguez
@wendyrenerodriguez 2 ай бұрын
I unplug the machine from the power but do I unplug the water before I drop it up and start working on it
@raulcoronado4292
@raulcoronado4292 2 жыл бұрын
Greetings, Jesus, I think I have a similar washing machine with a model (wa45n3050aw/a4). My question is the following: When the spinning cycle is almost over, the washing machine begins to move very abruptly to the point of stopping automatically and starting the washing cycle again, filling water the tub from the beginning I already did some of the steps you recommend in this video like cleaning the tps sensor and leveling the washer on a flat place I really don't know what else I can do or if you have had a case similar to this before? what do you recommmend me to do
@Garfield0123
@Garfield0123 4 ай бұрын
My samsung washer has same symptom shown on your video. I went under to check the sensor on the clutch assembly, and I saw the plastic sensor was broken in half. I could not find how to buy just the sensor, the whole assembly is about $250. I tried to repair the plastic sensor (with super glue and thin strips of electrical tape). It is still not working. Best to get a new one, or would you try to repair?
@JesseApplianceRepair
@JesseApplianceRepair 4 ай бұрын
Also check the rubber seal. They have magnets where the sensor reads. Should be 3 little magnets. Make sure they are still there.
@Garfield0123
@Garfield0123 4 ай бұрын
@@JesseApplianceRepair i saw one loose little magnet on the pulley wheel when I removed it. I put it aside. A new clutch assembly was delivered and I will check it out tonight. Thank you!
@user-nh9ji3mr1v
@user-nh9ji3mr1v 6 ай бұрын
Iam from México in have a silimar washer but this one is invertert system but it has the same problem doesnt spinmy question is it had the same sensor?
@kimraley1050
@kimraley1050 Жыл бұрын
Hi Jesus, I’m hoping you can help me. I need to replace the harness that attaches the TMR sensor to my Samsung WA40J3000AW/AA and I can’t find it anywhere. It looks just like the one in your video
@alexismoreno3696
@alexismoreno3696 Ай бұрын
Buenas tardes mi lavadora marca el destello en el led de eco tibia y de acuerdo al Manuel dice que un botón no está activo, que podría ser?
@michaelstinger6785
@michaelstinger6785 2 жыл бұрын
hi there i have the same model as of right now it has a hot & cold error it does not agitate or spin i cleaned the tmr sensor nothing what would you think thank you
@debracavalieri4871
@debracavalieri4871 Жыл бұрын
Great video!
@eugenemoreno4797
@eugenemoreno4797 Жыл бұрын
I have the same washer, it does no spin but does make a grinding noise everything else does work properly. My sensor had a lot of grease on it so I cleaned it put it back but it did not correct it. My main worry though is the grinding noise it makes. It l lasts about 2 or three seconds stops then does it again and again. What should I be looking for?
@braedonballard6637
@braedonballard6637 Жыл бұрын
Hello, I have this model washer. It will only work on rinse and spin, will run through the whole cycle. None of the wash cycles will work, it adds a little water then starts flashing with a buzzing sound. Could this be a sensor issue also? Thank you!
@commieslayer8218
@commieslayer8218 2 жыл бұрын
Great instructions, I got Samsung top load WA45M7050AW/A4 4 years old and the water pump rubber toilet flapper like check valve is separated from the rubber bushing holding on the orifice. Those who gave me the washer told me that it wasn't spinning at times and I suspect that the flapper just got wedged and blocked the port at least partially so too much of water was perhaps sitting in the basket and sensor didn't allowed to spin it. No code is displayed and if there was one, they didn't record it so I don't know. When the pump runs, I can hear the flapper ticking/knocking so I am looking for that part and it maybe an issues to find it. When it spins, I don't see and hear water shooting into the basket like on other washers helping to flush out debris and detergents, maybe not included option of this model, manual has no mentioning about it.
@lysunny1989
@lysunny1989 Ай бұрын
I have the same model and the whole cycle works and just not the last high spin cycle the clothes end up soggy what could be the problem ?
@666Yumaaz
@666Yumaaz Жыл бұрын
what # part is the sensor you changed? thanks for sharing
@user-rk2ol1ob7m
@user-rk2ol1ob7m Жыл бұрын
Hi! I have the same problem. Did it fill with the water 💦 or no?
@stevenfroeschl7056
@stevenfroeschl7056 Жыл бұрын
Hello, this model washer do you know why the load size jumps to extra large? Could it be this sensor? Thank You
@josephhostetler7788
@josephhostetler7788 2 ай бұрын
Need a new rubber bearing seal for a Samsung model no. WA45N3050AWA4 can you help me? Thanks!
@lionelneals9078
@lionelneals9078 Жыл бұрын
I have the same model washer. I did a diagnostic test and the Large light is flashing. The washer would start an run water longer than usual starts to wash and cuts off giving me the Large light blinking. What could this possibly be?
@sheilasantana1716
@sheilasantana1716 2 жыл бұрын
I have the exact same washer it was working perfectly fine yesterday. I try putting it to wash today but as soon i push the start button the blinking light came on it won't spin just dead silence i was hoping maybe you can tell me what's wrong with my washer?
@JesseApplianceRepair
@JesseApplianceRepair 2 жыл бұрын
things to check. if as soon as you click start and no noise happened. Check your door lock. if it does not lock it wont start. if it does lock check water pressure. see if water is coming in. if not check faucet. but if it does start and adds water but does not drain to spin then its your Drain Pump. Let me know.
@user-cb3dp1ww3d
@user-cb3dp1ww3d 9 ай бұрын
Hi, I have this exact washer, and it stop spinning, and it's making a noise when it comes on, and it's not doing anything at all, can you help me, I kind of think I put in to many jean pants as well
@user-mx5by3nc5d
@user-mx5by3nc5d 2 ай бұрын
I have this same washer. When I go into diagnostic it tells me lid lock. So I bought a new one installed it and still don't work. It clicks like it should but don't actually lock
@antoninbrown4440
@antoninbrown4440 2 жыл бұрын
Have this same washer but it wont drain, i cheak the water pump its not clogg and the lil cable underneath still intack. Could you tell me what could be the problem please if you can.?
@nando4755
@nando4755 23 күн бұрын
What is the part number for this sensor ?? What is the name of it ?
@davenportchurchofgodbyfait8643
@davenportchurchofgodbyfait8643 2 ай бұрын
How can I get that part?
@noelcaudilla4877
@noelcaudilla4877 Жыл бұрын
Good job,thanks
@sbb526
@sbb526 2 жыл бұрын
Is there anywhere to get just the sensor, no need to replace the entire clutch assembly is there?
@lindal390
@lindal390 Жыл бұрын
My door lock is broken. Can it be bypassed?
@brendapryor8713
@brendapryor8713 2 жыл бұрын
hi i was wondering if you could help us out we have this same washer and it wont spin or drain..and it codes hot.warm..thankyou !
@lesliedaisley7846
@lesliedaisley7846 2 жыл бұрын
Bro what is responsible for determining the water level on these model I have one that is giving 2 problem 1st When adjust to the level of water eg : medium or high on completion of fulling to that level it automatically goes to Extra High on fulling level, the rense process is the same . 2nd issue: during the spin process coming to the completion process it starts nocking around in the drum ( Bang Bang Bang ) and the item been spin never get dry . And do these unit come with a tech sheet hidden anywhere in the machine
@darlenelertora3939
@darlenelertora3939 6 ай бұрын
I have the same model, but when it has to spin, it doesn't do it, instead it starts filling up with water, like to start the washing again...whst it could be???
@meemoo6885
@meemoo6885 7 ай бұрын
Hi jesus ,I hope you doing well, do you have the repair manual of those washers....could you share it with me?
@JesseApplianceRepair
@JesseApplianceRepair 6 ай бұрын
Hello, Most machines actually have the Manual inside. some have it sinde the main control board. remove the back cover of the top head. other ones will have it stuck to a inner wall where the main tub is. if you lean the machine on its side and pick in you might see it. Hope that helps.
@chelseaalexander7397
@chelseaalexander7397 Ай бұрын
@@JesseApplianceRepairI had one but cannot find the manual….please help….mine looks clean and brand new…checked springs last night and pump and hose….so I’m thinking it’s something small like you’ve mentioned….sensor or magnets….what are the bearings exactly?? 😢😂
@adriennesmith2133
@adriennesmith2133 2 жыл бұрын
I washed a blanket on bedding. It washed but it would spin or rinse. I left it alone for a while then started a normal cycle for a test without clothes. And it went through its cycle without interruption. I repositioned the blanket just in case it was unbalanced. And as I mentioned before it did not spin or rinse. What could be the problem? Any advice? Thanks.
@JesseApplianceRepair
@JesseApplianceRepair 2 жыл бұрын
I assume the washer is similar to the one I have on the video... if that's the case then it sounds like the blanket is going of balance when it wants to start to spin. First make sure the washer drains all the water completely. if it doesn't then the pump is the issue.. bad pump or something stuck.. if it does drain next thing is checking the washer in other cycles by itself. no clothes. try at least 3 different cycles.... if the washer completes all the cycles then The shocks of the washer are the issue..even if you balance the load at the beginning the washer will still agitate and move the blanket around while in the cycle. and when it trys to spin it might shake and restarts itself and after a few trys it will stop. one way to check if the shocks are good in the washer is by pressing down on the tub while empty (no water - no clothes) . SO you put your hand inside the tub while completely empty and press down and release quick. if the tub goes down and up and stays the shocks are good. If the Tub Bounces more then once when released then the Shocks are bad. Let me know
@cpo001
@cpo001 Жыл бұрын
I have the same model. The problem I'm having is it's making a clicking noise and it's not draining completely...Is the actuator supposed to pull the arm during the spin cycle or all the time
@JesseApplianceRepair
@JesseApplianceRepair Жыл бұрын
sounds like the actuator is bad. sorry for the late reply. The actuator has a little motor that turns and pulls the arm to go into spin mode and sometimes the motor warns out and it releases it which makes the click sound. so it needs to be replaced.
@silviomontenegro620
@silviomontenegro620 11 ай бұрын
Es posible dejar desconectado la lavadora Samsung digital del toma corriente de Alimentación por mas de 24 horas, no se desconfigura la computadora
@HandyTim
@HandyTim 2 жыл бұрын
Do you know how to initiate a diagnostic test on this type of washer?
@Mrsquick
@Mrsquick Жыл бұрын
Power on the washer, once powered on press and hold the temp button that will put it into diagnostic mode. Whatever light flashes that's your code.
@HandyTim
@HandyTim Жыл бұрын
@@Mrsquick thanks for that
@Mrsquick
@Mrsquick Жыл бұрын
@@HandyTim You're welcome.
@altie40
@altie40 Жыл бұрын
I have been trying to locate that tmr sensor. Can you help me out, please? Thanks. Al.
@JuanHernandez-eg2qg
@JuanHernandez-eg2qg Жыл бұрын
Hermano gracias i have one similar but my do a grainy noise while spinning I change the clutch but I can’t find the problem do you know what can be the problem?
@sheldon.narine.7763
@sheldon.narine.7763 Жыл бұрын
I have this same model machine, the issue im having is when the cycle reaches spin, it will start to spin but sometimes the barrel will start to bang on the walls, then the spin cycle restarts. The water drains then refills. What do you think can be the issue?
@sheldon.narine.7763
@sheldon.narine.7763 Жыл бұрын
One more thing, an alarm sometimes comes on and all the lights start to blink.
@HandyTim
@HandyTim 2 жыл бұрын
I just got the same washer and there's black grease leaked on everything what do you think caused that? The grease is on the belt pulley and has even gotten slung to the springs
@HandyTim
@HandyTim 2 жыл бұрын
Actually I figured out where the black grease came from. Someone tried to fix the springs/rods using sticky grease and it didn't work. Now I'm thinking that sticky grease is on the sensor. Funny thing is the washer worked before sending it back out the door but now customer says it doesn't work at all.
@random23145
@random23145 Жыл бұрын
How much does that sensor cost??? Having the EXACT problem with the EXACT model in this video...
How To Use Diagnostic Mode On A Samsung Washer To Fix Any Issue!
8:38
DuctTape Mechanic
Рет қаралды 46 М.
How to Find Samsung Washer Error Codes & Fix a Samsung Washer Not Spinning
11:18
Bens Appliances and Junk
Рет қаралды 355 М.
Schoolboy Runaway в реальной жизни🤣@onLI_gAmeS
00:31
МишАня
Рет қаралды 4,1 МЛН
طردت النملة من المنزل😡 ماذا فعل؟🥲
00:25
Cool Tool SHORTS Arabic
Рет қаралды 24 МЛН
Top Nine Reasons Your Older Style Washer Is Not Spinning!
9:28
DuctTape Mechanic
Рет қаралды 246 М.
Samsung Top Load Washing Machine Review | how to repair when it breaks
8:25
Centennial Renovation
Рет қаралды 36 М.
Samsung Top Load Washing Machine Grinding Noise Diagnose | Repair
7:41
You Can Fix That
Рет қаралды 97 М.
11 de marzo de 2023
1:27
Aurelio Reyes
Рет қаралды 206 М.
Samsung Washer Machine Not Rinsing or Draining
7:43
Adrian Navarrette
Рет қаралды 30 М.
Samsung Washer Repair - Will Not Spin or Agitate - Washer Clutch
2:59
ApplianceVideo.com
Рет қаралды 64 М.
Samsung Top Load Washer UB error during spin cycle fix
6:04
MrKnowSomeThings
Рет қаралды 58 М.