I've used the Das Mikro, AGF and Powerstar receivers which are all telemetry compatible and all compatible with the M12S. The only issue I had was one powerstar receiver had the channel sticker on backwards, but they all follow the same arrangement from left to right. Sanwa has a really good list of their official receiver compatibility here: sanwa-denshi.com/rc/common/pdf/TX,RX%20compatible%20with%20RF190514.pdf

You can do this with the 'interval timer' function, setting the timer to 5 mins and turning on the 'start trigger' function. This can be found in the setup menu under either INT1 or INT2. It will keep going after 5 mins, so you may wish to assign a button to 'interval timer' so you can hold it down to stop the timer. Check out page 73 & 74 in the manual.

From the VXL3S manual: 1. Connect a fully charged battery pack to the VXL-3s. 2. Turn on the transmitter (with the throttle at neutral). 3. Press and hold the EZ-Set button (A). The LED will first turn green and then red. Release the EZ-Set button. 4. When the LED blinks RED ONCE. Pull the throttle trigger to the full throttle position and hold it there (B). 5. When the LED blinks RED TWICE. Push the throttle trigger to the full reverse and hold it there (C). 6. When the LED blinks GREEN ONCE, programming is complete. The LED will then shine green or red (depending on low-voltage detection setting) indicating the VXL-3s is on and at neutral.

There is just one 2.5mm hex screw to undo, then slide in the hook and put the screw back in. Page 13 of the manual has instructions.

@@factoryrollracing3847 tq

Sorry, must have missed this comment a while back. Hopefully you got it sorted, but for anyone wondering go into the system menu, then 'bind'. Scroll to the bottom of the page after setting which protocol to use (NOR, SHR, SSR) for your steering and throttle. Just use SHR mode unless you are using an analog servo (NOR) or a Sanwa Servo (SSR). Press bind on the screen first and you should see flashing arrows. While holding the bind button, power up the receiver. Press bind again on the screen and you are done.

Not that I know of Paul, only to delete the individual models which doesn't change the 'system' settings of the radio.

Switch to an empty model on your radio and go to the system menu, then choose 'Type'. Setting this to "TYPE IX" will give you steering on channel 1, front throttle and brake on channel 2 and rear throttle and brake on channel 3. I don't have an MOA crawler but you could use dual rates or EPA adjustments to set the overdrive. I'm not familiar with how to set up the more advanced AUX mixing for dig/burn etc.

@@factoryrollracing3847 this is very helpful I'm trying to deal with it right now I'm almost giving up

@@factoryrollracing3847 my brother I thank you so much from the bottom of my heart seriously I can't believe it 21 minutes later I do exactly what you say and I'm already rock crawling in my living room thank you so much. 👍🏻🔥😎🔥😎🤙🏻🤣😂🤣👏🏻👏🏻👏🏻

@@driftcraze2138 great news, happy I could help! I've looked at my radio and can help more now too.. no need to adjust dual rate or endpoints to adjust the overdrive there is a specific 'MOA Mix' that will appear in the setup. If you go to the System menu and Assign the lever (or dial) to MOA mix then you can easily adjust the amount forward/rear drive bias. Still not sure about how to do dig/burn though.

Are you sure the receiver is bound to your radio? Can you move the steering servo? You can also check that your throttle trim is centred before calibrating the ESC, or try reversing the throttle channel. You can also go into the throttle type menu and set it to F5:B5 (page 44 on the M12S manual) before trying to calibrate again.

No succes, I try all that. Also got one of the guys that have another M12 radio to try his and same issue. So its no the radio but also not the ESC since we can make it work with a cheap radio.

@@user-dh3wl7ec7j so no movement of the steering servo?

If the steering servo isn't moving you've likely either: 1. plugged in the servo/esc connectors backwards 2. failed to bind the receiver to the transmitter

Try a refresh or restart if the sound isn't working in youtube!