Screw Chuck - Who Needs One?

Рет қаралды 5,465

11 ай бұрын

I show you how to make a large screw chuck for fast mounting of cross grain projects like bowls, plates and platters. I show how to lock the screw. If you find my videos helpful, you can buy me a virtual cup of coffee with this link. www.buymeacoffee.com/mikepeace3Y
As an Amazon Associate I also earn from qualifying purchases from my Amazon shop www.amazon.com/shop/mikepeace....
You can download demonstration handouts, downloadable copies of articles I have published, and other useful woodturning information available on my website www.mikepeacewoodturning.com/

Пікірлер: 37

@norm5785 11 ай бұрын

Thank you for sharing, everyone stay safe, happy and healthy. From Henrico County Virginia

@MikePeaceWoodturning 11 ай бұрын

U2 @norm5785!

@pjseiber2774 11 ай бұрын

Very nice 👍

@MikePeaceWoodturning 11 ай бұрын

Thank you 👍

@10DrKenHarper-bo3rf 6 ай бұрын

'Thanks for sharing. .-

@MikePeaceWoodturning 6 ай бұрын

You bet!

@cobberpete1 11 ай бұрын

Bought you a few coffees. It's about time I showed you some appreciation for all the tips over the years

@MarklTucson 10 ай бұрын

Thanks for putting this out. A couple things: I followed your link and got a set of the countersinks you used. I just ran into an issue drilling a pen blank with the drill bit wandering more than I wanted as it went into the little dip left by the live center; I think these will help mitigate that. Secondly, that use of a piece of strap iron to reinforce the lag screw is brilliant -- that should really help with the longevity of the screw chuck.

@MikePeaceWoodturning 10 ай бұрын

Another option besides the strap is to file the inside of a fender washer with a couple of holes or notches to hold it.

@glencrandall7051 11 ай бұрын

I do not have a face plate ring. So instead I just glued on a piece of 1/4 inch stock which I turned to dovetail shape to match my biggest chuck jaws. I recessed and glued with epoxy the head of the lag screw. It works pretty well and saved me about $30. Thank you for sharing, Have a great day and stay safe.🙂🙂

@MikePeaceWoodturning 11 ай бұрын

Yours is a good solution.

@jackthompson5092 11 ай бұрын

Great idea Mike.

@MikePeaceWoodturning 11 ай бұрын

Thanks 👍

@randyrockwell6136 11 ай бұрын

Thanks for another great tip Mike 🤠🇨🇱

@MikePeaceWoodturning 11 ай бұрын

Any time!

@theangrywoodturner9972 11 ай бұрын

Nice idea if you don't have a chuck and woodworm screw ..and Nice touch with the little bracket to insure the screw doesn't slip. Thanks

@MikePeaceWoodturning 11 ай бұрын

As one viewer commented, you could modify a fender washer also

@zetuskid 11 ай бұрын

Hey Mike, great video. I’m gonna follow your instructions and make me one . I think even I won’t mess this up😅!

@MikePeaceWoodturning 11 ай бұрын

You can do it!

@BobBlarneystone 11 ай бұрын

I would be inclined to use a hardened lag bolt. To secure the bolt's head, I would counterbore and fill with epoxy - good ol' J-B Weld.

@MikePeaceWoodturning 10 ай бұрын

A hardened screw is not necessary. Epoxy has failed me in the past for holding a lag bolt. YMMV

@knawedArt 11 ай бұрын

Thanks for the tip. An automotive body or fender washer would be a good alternative for center screw support.

@MikePeaceWoodturning 11 ай бұрын

Excellent suggestion. Thanks!

@LewisKauffman 11 ай бұрын

Thanks Mike!

@MikePeaceWoodturning 11 ай бұрын

You bet, Lewis!

@emgiwoodworks 11 ай бұрын

I recently made one myself, it looks pretty similar! 😎

@MikePeaceWoodturning 11 ай бұрын

Cool!

@georged1209 11 ай бұрын

Chuck may object to your suggestion, however, I Screw Chuck frequently and am usually satisfied with the results. Especially helpful on small bowls to finish the bottom completely, with a small tenon or recess for reversing on the scroll chuck, before hollowing the inside.

@MikePeaceWoodturning 11 ай бұрын

Thanks for sharing!

@_Egor_Egorov_ 11 ай бұрын

Thank you very much for your informative video. It is not necessary to drill a hole for screws. The screws are well screwed in without holes. Check on the board trim. 4:19 do not use a scraper, use the wings of the reer (Bowl Gouge - 55° - 60°). Health and success in work. Thank you.

@MikePeaceWoodturning 11 ай бұрын

Yes, a bowl gouge could be used. It is a matter of preference. I find my approach on drilling the center hole better insures centering. Just using a screw can be off a tiny bit. YMMV

@_Egor_Egorov_ 11 ай бұрын

@@MikePeaceWoodturning The scraper scrapes the wood and can pull out part of it. bowl gouge - it cuts wood without pulling it out. You still center the tree with a chisel after screwing :) Thank you.

@tomcoker9882 11 ай бұрын

Mike nice project and will prove useful. However, my OCD side kicked in when I saw you went through the board without either filling them in, or jprobablly better, go back and drill the others all the way through. The holes would then make a symmetrical pattern on the front of the plate. 🙄 Cheers, Tom

@MikePeaceWoodturning 11 ай бұрын

Singers have to sing and dancers have to dance.

@danceswithaardvarks3284 11 ай бұрын

It's a great idea as long as you have a spare face plate. Does the larger back plate provide more support for the piece being turned, compared to using a regular worm screw that mounts in the chuck jaws?

@MikePeaceWoodturning 11 ай бұрын

You could always glue to a threaded glueblock. Or as Glen suggested in his comment, just turn a tenon and hold it in a chuck. Yes, the larger wood surface makes it stronger as it provides more friction but also more lateral support. I find this easier to mount and dismount a blank compared to using a woodworm screw.

@danceswithaardvarks3284 11 ай бұрын

thanks