Im going step by step in order to protect drivetrain until I can reach max potential. So far everything looks good so we keep pushing😁.

Yes, there in. Its just the worm gear reduction we are fighting here. Even the Treal overdrive only speeds them up by 18%. But its not an issue we still have 4.2 more volts which turn out to be another 25k+ rpm out of this motor and we can still double the pinion size which in turn doubles max speed so we are well withing the mark. 👍

They go on the LCG Revolver mount.

@@Gamyrc I'm currently running rear motor in a Venom. Do you forsee any problems with running the revolver mount the same way with the Toro in it?

@@lockenetmonster5029 I use the Castle 0808 which is same size with my venom on a forward motor configuration and it works fine. Shouldn't be an issue in rear.

@@Gamyrc I just received and installed the Lizard. I can do the supper slow crawl but then throttling up as slowly as possible it's jittery and jumpy. Also when I max throttle the motor stops and the esc blinks 3 times. I have a 4 channel Austar radio and it didn't do that with the hobbywing esc. Recalibrated multiple times and reset to factory settings too. Any thoughts?

Also, can you supper slow crawl in reverse? Mine won't. I'm just going to ship it back to Vietnam and continue waiting like I have been for a month.

Each motor has its own variation of the motor plates. The 1410 Rocket uses the V3 motor mount thats used on a 130 motor. The larger 2080 size motors like the one tou see here use the LCG 380 motor mount.

@@Gamyrc and correct me if I’m wrong, but the surpass 1410, the 14 in how wide it is then 10 is how long it is? But that seems very small, would it still have the torque to do the very slow crawl on the 3500 or 2500 KV?

@@raleighro On that particular model the numbers dont match the size. That motor is around 15mm wide by 28mm long.

@@Gamyrc thank you very much for your help, do you think that the 3500kv surpass hobby rocket 1410 would have the low speed control for that crazy low speed?

@@raleighro Only if you use the Furitek esc.

I'm wanting to give my Wraith Spawn big power for rock racing, but also use it crawling.

Not that I know of. The closest thing is Castle esc's. As far as I know Furitek may be working on a larger version but eta would be purely a guess right now.

@@Gamyrc I figured. Thnk you for your info, and all these neat builds to watch. So many great ideas

Just for testing. I have paddle tires for the actual runs.

Havent had any issues. Did you update to firmware 1.3?

@@Gamyrc I did, it seem to stutter, be delayed and sometimes not recognize the motor, but I also blew the stock esc with it, so I think that might have created the problem, but It works great on 2s. I also reset it but no luck. No just waiting for a response fro.the company.

@@jepmpa3285 That is a very large number of issues! The one that has me thinking is the part where it blew your other esc. Not sure why thats would happen. Unless you placed battery on stock esc and then tried to run new esc through it🤔. Then again, im not even sure it would turn on that way. Keep me posted on what they tell you!👍

@@Gamyrc I did the battery into the stock esc and then I turned the stock esc on first and I put the motor into the battery part where the battery is for the furitek, I never turned on the furitek. I posted all of it on reddit on the scx24 subreddit. In total I lost the stock 2in1 esc and a Barrage motor. Got an extra remote and Barrage motor tho. I was confused where to plug it because I didn't think you could plug a two pin motor into the 3 pin brushless section, until I read the instructions, I was watching a video of how to do it, but I couldn't see the plugs so I guess it.

@@jepmpa3285 The motor you connected to the battery part on the Furitek put a amp draw on the chanel two of the stock esc which is only powered by the stock esc's bec and was overwhelmed causing it to fry. This in turn couldve also damaged the Furitek 😔.