Full rebuild of a 720 SeaDoo Crank - all bearings - rods - pins and seals replaced. Trued and welded.
Пікірлер: 40
@timmy2dogsableАй бұрын
You helped me do much I purchased two motors 660 I'm definitely doing those. Timing gear moved
@izitwet11 ай бұрын
Dude, you obviously done a couple hundred of these... Impressive skills.. Thanks for sharing! Oh i suppose you could always put some loctite outside the bearing if you needed insurance it doesn't spin.. Good job
@bilel25627 ай бұрын
Great job
@Winnipeg_Jets_Fan10 ай бұрын
Cool video never seen how th8is was done. Thx
@gerardotorres996311 ай бұрын
Excellent video thank you. I just subscribed excellent job
@adamaxe16 ай бұрын
awesome
@user-ud7uc4lc3o5 ай бұрын
Классно!!! Сначала он кидает в коробку разобранный коленвал и щеки бьются друг о друга а потом он их чистит от забоин 😂😂😂
@user-rs9jv8fw2t4 ай бұрын
Чистит то не от забоин а от нагара масляного. Но жесткой щеткой по месту работы сальников... я над этими местами дыхание задерживаю, тряпочкой с растворителем протирая...
@justinborishkevich6500 Жыл бұрын
Very nice 👍
@5StarPWC Жыл бұрын
Thank you 👍
@williamrae410711 ай бұрын
Hey, does the main journal gear have to be pressed in a certain way?
@dongesswin Жыл бұрын
Great Video what is the tool that holds the bearings called? And what is the part # for the bearings. I have to replace the second bearing in from the the PTO. Thanks!
@DownsouthMan Жыл бұрын
Thanks for making this video for us. Ive always wanted to know how to time everything. I did notice that on your first weld, why didn’t you weld the other part? You only ended up with 3 welds.
@JoelArseneaultYouTube Жыл бұрын
What size bearing splitter is that at 1:35 ? I bought a splitter kit with a few different ones, and they are all too small. I find the size ratings on them very confusing. I recently rebuilt a crankshaft and ended up building a puller tool because the tools I bought didn't work. Edit: I also notice that it looks like Sea-Doo is nice and leave a little space between the bearings and webs... On the Kawasaki cranks there is only a few thou clearance. Cheers.
@5StarPWCАй бұрын
It’s a 6”
@davemall18 ай бұрын
Ho much would you charge to rebuild a 587 crank shaft from a 91 XP?
@taylorcarson9213 Жыл бұрын
Hey I’m working on a 2001 1200 yam and I’m getting water in all three cylinders is there anything you could think of that I should look for? I got great compression so I was thinking it’s comming from something else that’s not the top end gaskets
@5StarPWC Жыл бұрын
Are you connecting a hose on shore when this happens?
@edisonjimenez1476 Жыл бұрын
Great video. Thanks for sharing. Where are you located, do you have a place to get parts from you? Thanks
@chrisbarker4271Ай бұрын
in one of your very helpful videos on a 720 you mention grease to swell the O rings in the top end. Is there any one that is better than others? Silicone, synthetic etc.. Thanks
@5StarPWCАй бұрын
I normally just use automotive grease.
@bilel25627 ай бұрын
What a metal use to welding is it aluminium or what?
@christopherdeguise92664 ай бұрын
what is welding rod use
@atypicalhiker Жыл бұрын
How did you remove the rear counterbalance? I think it is threaded but I cant get it off.
@5StarPWC Жыл бұрын
It has regular right hand threads, vise it then use a pipe wrench on the impeller tool, preheat the PTO counterbalance with propane and use a pipe for leverage.
@joeltolim Жыл бұрын
Great video, I'm getting ready to rebuild a 787 crank, this answered some questions and gave me some idea's on how to do this. Was that a .020 feeler gage on the rods also? Where do you get your bearings and seals from? Thanks for your time and knowledge, really appreciate it..
@5StarPWC Жыл бұрын
Normally I buy the seals from WSM and the bearings from bearing dealers.
@juanpabloramirez656510 ай бұрын
Thank's i like you no edit any and could see all how to do, only question is where to get inner seals
@5StarPWCАй бұрын
WSM has them
@angelitoore12 ай бұрын
Do you have for selling?
@hkcitation Жыл бұрын
Why do you weld the crank?
@5StarPWC Жыл бұрын
When you take them apart and reassemble them sometimes they can twist or loosen up when running. Welding just locks it in place.
@bearlydo18 күн бұрын
Do you do the 787 the same way
@5StarPWC3 күн бұрын
yes -
@Cultofpersonality091295 ай бұрын
When I get my cranks done I pay $1000. For what you just did in an hour with $50 worth of bearings and new connecting rods. Do you build stroker kits for skidoos? I have a triple 700, 809 and 780. Obviously the 700 and 809 are nikasil plated so they’d need to be sleeved or bored and repeated . 780 isn’t but has shorter rods the 809 I believe.
@5StarPWC5 ай бұрын
No sorry, i don't work on the snowmobiles.
@davisf3671 Жыл бұрын
Hi. Maybe you can help me to find where is problem. Engine run only idle and doesnt accelerate when to try accelerate then stall. Found rotary valve gear have change, carb rebuild and test pop up pressure that’s are good. Compression are same and good. I think maybe crankshaft are broken. kzfaq.infokLspWiS6990?feature=share
@5StarPWC Жыл бұрын
see if it has spark on both cylinders
@davisf3671 Жыл бұрын
I chek it it. In same have good spark. Maybe stator have some problems? Spark to early or to late?
@Cultofpersonality091295 ай бұрын
@@davisf3671something in your carb. Probably pilot jet. All they need is fuel, air, spark decent compression to run.its not the stator.