Secura/Svavo soap dispenser, motor replacement

Рет қаралды 5,376

video99.co.uk

Күн бұрын

These soap dispensers are sold with various brand names, most commonly Secura or Svavo. Motor failure is a problem, so here we replace a bad motor.
The motor we installed was: Mabuchi RF-370CA-22170
Original was 6V/CRF-370CH-23120
This soap machine is on Amazon (affiliate links earn us a little if you buy through one of these):
amzn.to/3ikZ7kg
amzn.to/365nAHU
Audio and video transfers: www.video99.co.uk/
Please support us on Patreon / video99couk
or Paypal to colin@video99.co.uk
Patreon members often get to view videos early.
Music “Let It Run” with permission, copyright Cristie/MacFarlane.
Sorry I do not offer an audio or video equipment repair service.
Nor soap machines!
00:00 Introduction
01:09 Start work
04:47 Shaft length problem
06:17 Reassemble
08:53 Demonstrate motor fault
10:17 Original motor markings and test
10:34 Conclusion

Пікірлер: 21

@alexlang5308 2 жыл бұрын

Dremel grinding tool, is always useful. :)

@gyrogearloose23 Ай бұрын

Thank you for your video. Please help me to find the right replacement motor . Which parameters do have to match about from body size and minimum length of shaft? I seem to get 3000 RPM at 12 V, up to 24 V. I can get 10,000 more RPM at 6 V. Initially, I tried RF-370CA-26100, 6V, 10200 RPM. Alas, shaft is only 5 mm. Pulley comes off during operation. The old motor is labelled 6V/CRF-370CH-23120-42/8200 Thank you

@DrCassette 2 жыл бұрын

Nice repair :) I'm looking forward to seeing the HDCAM SR machine!

@video99couk 2 жыл бұрын

That was a little surprise to drop in at the end for my regular viewers who know about these things.

@miyoshiumeki Жыл бұрын

How do you take the PCB out of the top and clean with isopropyl alcohol. I unscrewed the single screw. Do I have to also take the whole thing apart?

@video99couk Жыл бұрын

Yes all the outer cabinet work has to come apart. If you don't fancy that, try blowing out the sensors with a can of compressed air.

@MattRidzonPE Жыл бұрын

Do you have any ideas for the situation where the sensor never activates? In other words, the blue light never comes on, thus no pumping. New batteries did not help. On occasion it will decide to work, but then fail again.

@video99couk Жыл бұрын

Yes. Take the sensor PCB out of the top and clean with isopropyl alcohol. Then train users to not take their hand so high that they put soap into the opto sensor housing.

@davidnguyen1056 Жыл бұрын

@@video99couk How do you take out the top? Uncrew then what? pull it out?

@northernplacecorporation 2 жыл бұрын

1. Why do you think the original Secura soap dispensers are the best (rather than the newer models without the Secura branding)? And 2. When is the Sony SRW-5500 video coming out?

@video99couk 2 жыл бұрын

I'm in the editing phase of the SRW-5500 video, but this will might be a two-part because I have a replacement part on order. I just prefer the manual control on the earlier soap machine, which is still available.

@mannysarmiento-hr9mj Ай бұрын

Where can I get a belt replacement? I have the same Secura soap dispenser.

@video99couk Ай бұрын

I think the belt is neoprene, but it's much smaller than most of the belts on eBay or similar. Just a case of searching for a very small belt.

@northernplacecorporation 2 жыл бұрын

Wait... What?! A Sony SRW-5500! How the heck did you get that HDCAM SR VTR?!

@video99couk 2 жыл бұрын

I wondered who would be the first to spot that! That will be my next video.

@skeeterhawk439 2 жыл бұрын

I bought one of the same exact model and the pump went out. The main gear on the pulley shaft of the pump started spinning. Where can I get a replacement pump?

@video99couk 2 жыл бұрын

That might be more difficult to source than the motor. Sorry, no good suggestions for that, other than perhaps a second-hand machine.

@frankowalker4662 2 жыл бұрын

Nothing worse than a shaft that won't behave. (sorry, I'm a bit drunk. LOL). Nice Sony.

@zx8401ztv 2 жыл бұрын

What a posh way to dispense fluids :-D I was thinking i.r emitter and sensor side by side. Where the brushes touch the commutator would be important for direction and torque. Would a slight rotation of the brush plate give a better torque with worn brushes. You didn't need to steal your sons teeth he he :-D

@video99couk 2 жыл бұрын

Considering the work involved it dismantling, it's as well to replace the motor since it's not expensive.

@zx8401ztv 2 жыл бұрын

Yes you have replaced it :-D, i thought you would like to look inside the old motor and see what is failing in it. Not video making, just your own interest :-)