For those that have an issue with their scooter turning off while riding 10 seconds it turns off, this will fix your problem.
Пікірлер: 137
@chuyramirez37312 ай бұрын
Well, this video was intended for those that tryout everything and nothing worked, I understand that theres a lot of concerns over not messing with the BMS and all but Ive done this to a couple of scooters now and haven't had any problems and its been more then 2 years now and still running and charging and riding them to school, work and out for a ride out town. No issues or problems.
@marisaramirez82962 жыл бұрын
Thank you. No one shows how to do this. Excellent video
@chuyramirez37312 ай бұрын
Thank you, I'm still running that scooter as is and haven't had any problems
@choisongdong1234 Жыл бұрын
I like your video bro 👍🏿 Thanks 🌟🌟🌟🌟🌟
@kevins5016 Жыл бұрын
World’s longest explanation on splicing a wire. Actually… could be a drinking game.
@chuyramirez3731 Жыл бұрын
I KNOW 😁
@flosa19952 жыл бұрын
If you have this issue then just revert to an older BMS version and it works most likely again. Had this issue on mine (after an firmware update) when using more than 20A and accelerating suddenly. It was on BMS Version 1.5.6 I reversed to 1.3.4 and it goes up to 65A without an issue now. Might work with other versions too but I stuck with it.
@chuyramirez37312 жыл бұрын
Yes, thank you
@E-supermoto5 ай бұрын
How did you reverse it??
@flosa19955 ай бұрын
@@E-supermoto was some time ago, I think I did it with shu, same tool as you use to flash the normal firmware, it even lists you the different versions for flashing. Just beware that depending on how new the scooter is there might be limitations imposed by ninebot
@flosa19955 ай бұрын
@@E-supermoto scooter hacking utility
@koreyalstin73372 жыл бұрын
😎it works no more turn off..thanks for your help 👍
@remussebastianmadmax58165 ай бұрын
discard direct, no bms discard onli on charge on bms, it veri bad..etc.
@chuyramirez37312 ай бұрын
2 years and still running
@brianjohnson167110 ай бұрын
thanks for this video! i've got 15 ninebot G30 Max scooters (orig SPIN Rentals) ... SNSC 2.0. from impound yard, i've flashed 4 successfully via ST-Link Flashing method of BMS, ESC, and Dashboard BLE... however, all of the remaining Batteries- although the LEDs flash Blue, i cannot get them to connect in software STVP, in order to flash the old BMS 1.3.6. despite good soldering skills, still no luck connecting. i'm gonna try this bypass myself, to hopefully get these batteries working. thanks again!
@chuyramirez373110 ай бұрын
Hi, the video was meant to show how to bypass the BMS that the scooter rentals blocked 🚫 so you can't use the scooter, I've had this scooter running like that with the bypass over 3 years and it still running and had no issues. Glad this video helped you
@haydeng953823 күн бұрын
Spin scoots need esc, display and bms flashed all at once I’m pretty sure
@haydeng953823 күн бұрын
This guy is crazy. Just putting electrical tape on it lmao. Also nice pink wheels(aren’t those exclusively for Lyft? lol
@iso-ou9kf9 ай бұрын
Hello Friend. Please tell me whether the short circuit protection will work with this kind of bypass of the BMS? upd: Did my research on the BMS board - This bypass removes short circuit protection... On the other hand, you can get more output power. =/
@chuyramirez37312 ай бұрын
2 years and still running
@Tate952 жыл бұрын
Ayyy matey!! Yooouudaaaamaaannnn!
@nonstopsaurier2 жыл бұрын
So I tried using this battery for a project and was facing a 5V reduced output voltage. I bypassed the BMS like this but used a fuse and get full voltage now. I think that should be done at least as the BMS protection features for the output are bypassed as well... 42V/very high current is no joke... and also over discharging needs to be avoided due to the missing cutoff...
@RandomClips27. Жыл бұрын
Most controllers have built-in lvc so no need to worry never had trouble with mine i did test it for the 1st few times tho just to make sure it cut off at the right voltage
@chuyramirez37312 ай бұрын
2 years and still running
@oop2989 Жыл бұрын
Hey, i got a bms from ebay could you do a wiring diagram or
@juanlara12572 жыл бұрын
Hola amigo, tengo una duda hay un video donde pues trabajo que que que soldar un cable rojo a una pinto P de la placa de la batería 🔋, sabe si esto es correcto? O cual Es la función del colocarle un cable rojo, aparte del soldar el negativo (bypass)
@chuyramirez37312 жыл бұрын
Bueno, no se cual cable rojo habla, pero es un cable negro como muestro en el video para poder alcanzar el coneccion con el cable negativo con de la pila.
@ivanshinoda2 жыл бұрын
Que onda Chuy a ver si me puedes ayudar, tengo el mismo scooter que tu pero el mío está bloqueado, compré un dashboard bluetooth en ebay pero la conexión es de 4 pines y el del patín es de 5 pines, ya sé que si se conecta así se quema el dashboard por eso hay que hacer un reacomodo de cables en la controladora de velocidad y aqui viene la pregunta del millón: Si le pongo el Dashboard que compré, reacomodando los cables obviamente para que no se queme y hago el bypass que hiciste en el video ya con eso puedo usar el patin? Otra pregunta, sabes de cuántos volts es la luz delantera? De antemano muchas gracias y saludos desde Tijuana.
@chuyramirez37312 жыл бұрын
Q' onda... Mira luego hago un video de nuevo en como configurar la coneccion del dashboard al controlador y si la lampara es de 5v. Aqui esta como se ve el cable, solo hazlo asi como el la foto Check this out on eBay! For Ninebot MAX G30 Scooter Dashboard Control Cable Board Line Wire #US www.ebay.com/itm/393792975660?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=ffyt2_pzsfe&sssrc=2349624&ssuid=h55E6dUHQJa&var=&widget_ver=artemis&media=EMAIL
@ivanshinoda2 жыл бұрын
@@chuyramirez3731 Muchas Gracias Chuy, entonces si hago tu bypass de la batería y le compró el cable qué me mandaste y el dashboard ya con eso puedo usar el patín libremente?
@chuyramirez37312 жыл бұрын
@@ivanshinoda bueno, aun tendras que flashar el controlador o consequir uno tambien
@ivanshinoda2 жыл бұрын
@@chuyramirez3731 Acabo de comprar el St link para flashear. A qué controlador te refieres? al electronic speed controller (ESC) o al battery management system (BMS)
@chuyramirez37312 жыл бұрын
@@ivanshinoda debajo donde esta la pila, hay yn controlador y cargador. Tienes que flashar el controlador con el st link
@yosselynsierras366815 күн бұрын
El foquito si se pine rojo que significa?
@robertrobarge5294 Жыл бұрын
I have a scooter it's called a hover one journey. I'm having the same issue with my negative wire. The positive and negative wire doesn't show any current coming out of it but if I put the multimeter on the hot wire and touch it to the Post on the negative side of the battery it shows the voltage that I have in my battery but if I put the negative lead from the multi-tool on the black wire and hook it up to the positive lead on the battery there's no reading. Anyways my black wire has no power coming out
@chuyramirez37312 ай бұрын
Bypass it
@chrisdaniels4674 Жыл бұрын
Thanks chuy
@juanlara12572 жыл бұрын
Hola Chuy Una pregunta, compre el cable de 4 pines para sustituir el de 5 pines que viene originalmente con el equipo, y compre un controlador chino en AliExpress. Para sustituir el original ya que me han comentado que este quema la tarjeta de control por que trabaja a diferente voltaje y que aparte está bloqueada. No se que tan cierto sea. Pero La pregunta es si conecto todo, pero no realizo el bypass que sugieres de la batería tendré algún problema?? o está se apagará al poco tiempo que está este en marcha? O peor aún puedo quemar la tarjeta controladores “display”. Esa es mi duda. Me puedes ayudar. Te lo agradecería infinitamente.
@chuyramirez37312 жыл бұрын
Hola, para liberar la patineta ocupas el controlador flashado o compra uno por Ebay o Amazon hasta tambíen Walmart online, Mas tambíen puedes comprar todo el kit ( Dashboard + Controlador) mas el cable de 4 pins y listo, prende pero se te apagara en menos de 10 segundos si no flasheas tambien la pila (bateria). O tambien puedes hacerle el bypass. Yo tengo esa patineta funcionando bien y sin problemas con el bypass.
@juanlara12572 жыл бұрын
@@chuyramirez3731 Asi es Chuy, compre ese kit completo que mencionas, entonces es necesario hacerle el bypass a la batería para que funcione correctamente? Si solo conecto el kit y no le hago el Bypass se apagara vdd.
@chuyramirez37312 жыл бұрын
@@juanlara1257 te recomendo flashar la pila si no tambíen puedes hacerle el bypass y nada pasa, sigue cargando y no pasa nada, yo tengo una patineta con la pila flashado y el otro con el bypass y el del bypass no se me ah quemado y nada aun sigue como si nada...
@juanlara12572 жыл бұрын
@@chuyramirez3731 Como se flashea la pila? 😯 soy un novato en todo esto, tienes algún video para hacerlo? Es difícil realizar el flasheo. Me ayudarías?
@chuyramirez37312 жыл бұрын
@@juanlara1257 En esó ando, muy pronto hago un video
@canercam60902 жыл бұрын
Çok teşekkürler ederim oldu fakat riskli degilmi sizce bataryaya zarar gelmezmi patlamaz mi sorun yaratmaz mi ?
@chuyramirez37312 жыл бұрын
Your welcome
@chuyramirez37312 ай бұрын
Have been riding that scooter for about 2 years now and haven't had any problems
@Duh_vo_ploti10 ай бұрын
Ребята я делал по другому отрезал минусовой провод прям снаружи дрелью сверлил новое отверстие там откуда выходят провода заводил туда отрезаный провод и припаявал его к пластине минусовой которач идёт сверху на элементах и всё разберать весь аккумулятор не надо и всё работает проверено тысячу раз
@F5_STAR6 ай бұрын
А защита от короткого замыкания и от низкого напряжения пропадает с этим способом
@Duh_vo_ploti6 ай бұрын
@@F5_STAR да некоторые плюшки пропадают впринципе контроллер вырубается при минимальном значении поэтому ниже минимума не разрядит но если как то по другому то просто вольтметр поставить чтобы видетт уровень заряда
@fourknotsnowhere Жыл бұрын
i used this method but i still cant draw more than 2 amps from the pack. does the red need bypassed also?
@RandomClips27. Жыл бұрын
Your cells are dead
@fourknotsnowhere Жыл бұрын
@@RandomClips27. on two packs? they charge and discharge just fine.
@chuyramirez37312 ай бұрын
You probably have a bed cell or two, the scooter that I've bypassed is still running great.
@fourknotsnowhere2 ай бұрын
@@chuyramirez3731 i just checked the voltage of each cell on both packs, there all balanced fine. no voltage issues. i think its the charge controller limiting to 10amp output
@chuyramirez37312 ай бұрын
@@fourknotsnowhere check your controller, when I did mine the voltage was fine and been riding the scooter and no issues, the bypass should only make the scooter run, no voltage change or making the scooter faster. You might need to check on the controller 🤔
@reaanddiellademi27232 жыл бұрын
Hi again. I bypassed the bms as per your video and it worked for two days but now again it started with the same problem, showing E5 error code on display and shutting off. Also, it was discharging the battery very quickly, much quicker than usual (battety type is 36v 15ah). Should I go back to connect the scooter negative to the bms, and can you please help me to diagnose the problem as when I measure the power of the battery it shows between 37-39.5v, which means there is nothing wrong with the batteries, right? Is there anything else that forces the bms to shut off my electric scooter. Thank you for your support and your kind understanding.
@chuyramirez37312 жыл бұрын
Hi. That's odd. You could and just downgrade the bms that will usually work as well. Sorry to hear that issue, but my scooter that I did the bypass is still running and with no issues and plus everyone that has done it too are still good. Maybe you probably cut the wrong negative wire or something, doble check.
@reaanddiellademi27232 жыл бұрын
@@chuyramirez3731 Thank you for your reply my friend. No, I cut the B- and the P- from the BMS and connected them together and bypassed it, and as said above worked for two days although it discharged the battery faster than usual, and finally it started to do have tge same error code and signs again. I guess it must be something else that us causing the bms to shut off the scooter. By the way, is there any app or how to downgrade the bms? Thank you so much for your support
@chuyramirez37312 жыл бұрын
@@reaanddiellademi2723 max.cfw.sh/#
@chuyramirez37312 жыл бұрын
@@reaanddiellademi2723 or the Xiaoflasher app too.
@chrisantonio20112 жыл бұрын
I did this but now am getting an error 21
@pashko902 жыл бұрын
This "solution" is no good for number of reasons. In this case, if your battery have not stock sofware inside of the bms you need to restore it with st-link. Right now bms will not turn off in case of low voltage, cells falure, or FET falure. In previous vid you said what you changed a battery, what kind of battery did you used? it was not been a regular g30 retail pack.
@chuyramirez37312 жыл бұрын
Hi yeah, it wasn't a retail battery from ninebot max g30, got it from Ebay for $40 dollars, I think it's from those rent scooters, also bought some controllers too and they are bond to someone else, the dashboards are generic too but still got everything working by using Scooterhacking Utility.
@chuyramirez37312 жыл бұрын
By any chance, do you know where I can get parts to replace Ninebot max g30 from? I get them from Ebay & Walmarts website.
@pashko902 жыл бұрын
@@chuyramirez3731 i buy stuff locally rarely, but most of the time ebay or aliexpress.
@Maximum_djs2 ай бұрын
I couldn’t charge it after bypass..
@frankfernandez6027 Жыл бұрын
I’m getting err 10 with one dashboard and err 32 with other one
@abbasghasemi7572 жыл бұрын
What is the name of the small black electronic box?
@chuyramirez37312 жыл бұрын
Small black box ??? There's no thing on the video
@abbasghasemi7572 жыл бұрын
Bms name germany
@abbasghasemi7572 жыл бұрын
@@chuyramirez3731 Battery management of small box full of cables
@abbasghasemi7572 жыл бұрын
@@chuyramirez3731 My battery smells burnt and does not charge 9 monaten
@suprimussuprimus38762 жыл бұрын
@@abbasghasemi757 it would problebly be your bms the batteries doesnt smell like burned more like pure alchol it could be a transistor on the bms
@rubenhayastan4854 Жыл бұрын
У меня вопрос за что отвечают тонкие провода ?
@chuyramirez37312 ай бұрын
Hi, don't touch does wires they are charging and part of the BMS so leave them alone
@StrawberryBastard10 ай бұрын
im gonna have to do this i fucked a soldering pad and the trace went with it so i cant install to original bms software
@bmw7z2 жыл бұрын
Bypassing the BMS is Never a good idea. It's there to protect the batteries and prevent Fires which can easily happen under the right conditions with Lithium Batteries. Changing the version of BMS firmware is a much safer effective way.
@elimaki483310 ай бұрын
Ok, so make a video showing how. Or this is the option.
@einstift5915 ай бұрын
If you use a different controller like a vesc you need to bypass it. Aslong as you not go over 30Amps you should be fine. I currently got a vesc build in and since it still takes 1-2 months until i get the cells for my battery i bypass it.
@einstift5915 ай бұрын
Otherwise if you not bypass it is limited to 19A with diffrent controllers
@chuyramirez37312 ай бұрын
2 years and still running
@ivanborruel2 жыл бұрын
No es más fácil y mejor flashear la BMS?
@chuyramirez37312 жыл бұрын
Si claro, pero esté methedo es para aquellos que no saben o qué tengan como flasharlo. Tengo un scooter con el flasheo y otro como en el video con el bypass y no e tenido ningun problema.
@ivanborruel2 жыл бұрын
@@chuyramirez3731 es cierto, tienes razón.
@whitefeatherslinger819410 ай бұрын
Is the battery still running without any hasle
@chuyramirez373110 ай бұрын
Yeah, haven't had any issues. Still running
@whitefeatherslinger819410 ай бұрын
Cheers dude😎
@chuyramirez37312 ай бұрын
2 years and still running
@Sweetersweet200611 ай бұрын
Is this how u fix the 16 error code
@chuyramirez373111 ай бұрын
Yeah, so far no problems yet
@reaanddiellademi27232 жыл бұрын
Hi friend. I have the same problem with my scooter which is ifentical to g30 max and replaced the bms but still it is turning off after 5-10sec. Can you please tell me how to flash the battery so I won't need to bypass it. Thank you for your help!
@chuyramirez37312 жыл бұрын
Your going to have downgrade the bms, in order to make it work. If so, doesn't work your going to have to bypass it or get a new battery
@reaanddiellademi27232 жыл бұрын
@@chuyramirez3731 Hello my friend, Thank you for your reply, and for your support. Can you please explain to me, as I am a newbie in electric scooters, what do you mean by downgrading the BMS? Thank you very much fir your time and cooperation. Best regards, Avni
@reaanddiellademi27232 жыл бұрын
And by the way I installed the same power BMS as my previous BMS, which was 10s 36v 15a BMS which my scooter had it installed before replacing it with a same power type of BMS
@christianmontgomery49112 жыл бұрын
I see .So the bms will still function to charge .
@chuyramirez37312 жыл бұрын
Hi, yeah it still charges and stops charging when it's full, I still have that scooter running and have zero issues
@Neilukuk Жыл бұрын
@@chuyramirez3731 Does it make the scooter faster?
@andreimitrica77 Жыл бұрын
@@NeilukukI’m curious too that’s what I’m here for
@andreimitrica77 Жыл бұрын
@@Neilukuk damn bro been a whole year I don’t think we’re gonna get an answer 😂
@Neilukuk Жыл бұрын
@@andreimitrica77 Looks that way. I'm not going to risk my scooter without some more info.
@skilledcamman475227 күн бұрын
Is it safe though?
@skilledcamman475227 күн бұрын
what about discharge protection?
@chuyramirez373127 күн бұрын
That scooter you see in the video is still running, from my house to work every day, no problems charging or discharging, been more than 2+ years.
@skilledcamman475227 күн бұрын
@@chuyramirez3731 which scooter is that?
@skilledcamman475227 күн бұрын
also instead of doing this you can either install a new bms, or use a mcu to send commands to bms over uart.
@haydeng953823 күн бұрын
No
@remussebastianmadmax58165 ай бұрын
broo change the bms ...it easi
@chuyramirez37312 ай бұрын
This video is made for those that have tried everything to make these rental scooters run, BMS on these batteries that came with these scooters are made different from the regular stock batteries, downgrade the BMS sometimes won't work, you have to this bypass
@Sherlockohms3032 жыл бұрын
They charged my card $285 someone took my rental from me and they found it.
@danielwysocki37923 күн бұрын
sorry but after this appear error 21
@chuyramirez373123 күн бұрын
Error 21 typically indicates a communication error between the control board and the dashboard
@ciprianbeniuga50422 жыл бұрын
Man , i sugest to delete this video before more people se it and before is to late . Basically you cut out the over voltage , under voltage protection , and that is veery dangerous. Buy a new bms and redo that battery . Seriously .
@whitefeatherslinger81949 ай бұрын
Cant seem to find a diagram with a standard bms ,the harness wires has a looped wire so with a standard one it dont have it so im guessing its why ive burned the last bms ive tried.i gotta say i have this bypass on another bike and it shuts off when battery is empty but i always keep a eye on it when charging ,any help with a diagram would be appreciated 👍
@greggawronsr76437 ай бұрын
kzfaq.info/get/bejne/aLBzZdd_yquXcn0.html This video discusses a generic BMS replacement that likely keeps all the safety features active. (And he has a LOT of G30 batteries.) Not sure if having no BMS plugged into the ESC if the scooter will still run...? Haven't tried it.
@chuyramirez37312 ай бұрын
Already been 2 years since I did this to that scooter and still working with no issues
@octapc24 күн бұрын
This is not something an electronic novice, or even a hobbyist should do. This guy instructs people to take risks that can cause damage.
@chuyramirez373124 күн бұрын
3 years and still running, to work and back home with no issues, plus this video is intended for those with rental scooters that tried everything and want to use these battery packs so far no one has said otherwise.
@iandegroeve8198 Жыл бұрын
stop messing with your battery lol you will regret it
@chuyramirez3731 Жыл бұрын
🤣🤣🤣🤣 4years and no problem
@whitefeatherslinger819410 ай бұрын
@@chuyramirez3731that long on a pypass cable 🎉sweeeet🎉
@remussebastianmadmax58165 ай бұрын
you discard the bateri directli, on low no protection, it bad 😂😂😂😂😂
@chuyramirez37312 ай бұрын
2 years and no problem, still running with no issues