Replacing brake rotors and brake pads on Freightliner Cascadia #brakerotors #brakepads #brakecalipers More repair videos in the playlist on the link below: • Meritor differential d...
Пікірлер: 59
@connorhorkan76112 жыл бұрын
According to frightliner the caliper bolts are one time use and should be replace when ever removed.
@arlindkrasniqi33152 жыл бұрын
Bro next time don't beat on the hub to separate it from the rotor. Beat on the rotor. You are going to replace it, so it doesn't matter if you ding it or bend it with the hammer.
@timsinterwebs29362 жыл бұрын
Things that are a safety concern in this video. 1. Reuse of wheel seal and no cleaning of spindle. 2. Reuse of caliper bolts and caliper after using heat on them. 3. Over torque of disk to hub. When he went over them with a torque wrench afterwards they were already well past torque spec due to the use of an impact and they didn't turn at all with the torque wrench. 4. Improper bearing set technique and no check for end play. 5. No cleaning of wheel studs and mating surfaces. 6. Using a 1 inch impact to torque the wheel nuts well over spec instead of securing them with a lighter impact gun and then tightening them to full spec with a torque wrench. For the safety of everyone on the road please do not repeat these mistakes. If anyone is unsure how to properly do a procedure or repair please check the manufacturers recommendations.
@mricemell0w365 Жыл бұрын
you missed the biggest mistake in this video, these guys used a old brake pad and put it behind the new pad instead of rebuilding caliper or buying new everything else you said is spot on.
@guacamoleweiner699 ай бұрын
You are an awesome teacher to that young man
@valeriumoscalu75809 ай бұрын
Thank you 🙋🏻♂️💪🏼
@racecar78086 күн бұрын
How often should you change brake rotors ? And how many brake rotors are in Freightliner Cascadia ?
@Rcaceres3 жыл бұрын
Great video! Did you have to replace wheel seals?
@aaronwilkerson61503 жыл бұрын
Anytime you remove a hub the wheel seal should be replaced
@glackaglack15343 ай бұрын
All that work, I bet the rotor and brake are way more expensive than drums and shoes plus wheel seal. I prefer to struck with drums.
@valeriumoscalu75803 ай бұрын
Yes more expensive, and takes longer to replace, but they have a longer life too, and stopping distance is much shorter!
@vasileverhovetchi31693 жыл бұрын
Das ist wie immer toll!!!
@ryanstevenson49188 ай бұрын
You ain't tell what size sockets
@vasileverhovetchi31693 жыл бұрын
Super cool VALERAKI 👏!!!
@elpichonroadservice56503 жыл бұрын
Is it essential to have a torch in all brake/rotor replacement???
@buppyb3013 Жыл бұрын
How much in labor does it cost to replace one side?
@Fzoo14292 жыл бұрын
Question what is your trick to torque the caliper bolts? If your installation a new one?
@emmanuelchacon295011 ай бұрын
Makes me itch that the wheel seal was not replaced our the spindle was cleaned plus reususe of heated bolts coming from some one who does this everyday at a shop were everything is done by the book
@valeriumoscalu758011 ай бұрын
If you doing it by the book I can come to you and film a video while you doing it, so we can show step by step how to do it right! The wheel seal was replaced I just did have time to film everything when I am doing it by myself! My hands are dirty most of the time and can't use the phone every moment!
@36ELGALAN Жыл бұрын
I see you marked the brake caliper bolts to help with reinstall. My question shouldn't there be a torque spec for those bolts?
@valeriumoscalu7580 Жыл бұрын
Yes there should be a specific torque, and you need new bolts by the manual! I didn't found new bolts so used the old ones! Just marked to install them in the same place!
@36ELGALAN Жыл бұрын
@@valeriumoscalu7580 thank you for your video, very helpful for new diesel technician.
@valeriumoscalu7580 Жыл бұрын
You welcome, I am glad the video is helpful!
@viktorg27363 жыл бұрын
How many hours of labor for both side???
@Ruslan_Athletic_Trucking_USA2 жыл бұрын
The bad thing i have to use the old plate btw the pusher and the pad. But I dont have all of them
@pedropedro2837 Жыл бұрын
Thanks
@valeriumoscalu7580 Жыл бұрын
You welcome!
@alpha-ou7mwАй бұрын
What is the number of black bolt opener
@govinlama27314 ай бұрын
❤❤❤
@mricemell0w365 Жыл бұрын
those bolts probably would of came loose with a air gun or using a breaker bar first and shorter extension. but for real did yall use a old brake pad and put behind new ones? if the dot sees that truck, it would be off the road. these guys know how to kind of take it apart but i would not want them in my shop.
@georgegeorgepht3 жыл бұрын
What are your thoughts on disc brakes vs old school drums? Is it better or worse?
@valeriumoscalu75803 жыл бұрын
If it to speak about maintance I prefer drum brakes because it's faster and easier to do maintenance, but if to speak about braking performance definitely disc brakes, rotors a much better than drums, faster cooling down, lasting longer, and braking much better! A little expansive too but ia worth it!!!
@revareva23 жыл бұрын
Do maintenance in time! Pads are much cheaper then rotors, just put third set of pads on mine..
@revareva23 жыл бұрын
Wheel seals are more on labor.. In the long run drums much simpler and cheaper... Discs brake is like Ferrari is good when in right hands, I prefer combo truck and trailer, so far I have only on truck,
@ratbek_usa3 жыл бұрын
Freightliner Cascadia 2015 и умения сегодня трескался. Сколько стойт передний 2 диски менять с работы. Спасибо за ранее
@calinrusu5080 Жыл бұрын
Trebuie sa le vezi la mine cum sunt, pametnik trebuie la rotile celea!
@valeriumoscalu7580 Жыл бұрын
😆😆😆 te cred , am avut si asa cazuri , le_am pus la colectie!)
@SvampenJontis6 ай бұрын
Will this work for my Kia picanto 2003?
@burnjack291 Жыл бұрын
Whats the easy way to check the pads? Kind hard to see with wheel on Salutare
@valeriumoscalu7580 Жыл бұрын
Phone camera with a flashlight on! Salutare!
@marcelcovaci9922Ай бұрын
It should have a wear indicator on the caliper, 2 notches. As the pads wear out those 2 notches get closer to each other. At least that’s how it is on Bendix system. This is a Wabco? , I think it should have something similar. When the notches are close that’s when you should remove the wheel and inspect the pads. Remember, since there are no rivets ( like in the brake shoes) the thickness of the pads is good until it reaches 2 mm. If you’re Romanian Salut! Sănătate și numai bine!
@Ruslan_Athletic_Trucking_USA2 жыл бұрын
Can you order just rotor, without hub?
@valeriumoscalu75802 жыл бұрын
Yes!
@razaghumman24123 жыл бұрын
Everything on Cascadia is cheap.Great info tho thanks 🙏👌
@maintenanceteam2243 Жыл бұрын
Hello, where is your shop located ?
@armanijoseph80083 жыл бұрын
Yes i thats what am talking about
@alexandrpintea26653 жыл бұрын
Noroc, cit au costat piesele ?
@valeriumoscalu75803 жыл бұрын
Salut, nu mai tin minte!
@alexandrpintea26653 жыл бұрын
@@valeriumoscalu7580 Ok, mersi
@valeriumoscalu75803 жыл бұрын
🙋🏻♂️
@makincash33372 жыл бұрын
How do I adjust these brakes. Thank you in advance
@shreqboi1 Жыл бұрын
Diesel diaries ep. 009 | Replacing a Disk Brake Chamber #freightliner #diesel #dieselmechanic kzfaq.info/get/bejne/pcqWZ8JkuNG-Zok.html
@shreqboi1 Жыл бұрын
Adjusting bendix air disk brakes | Diesel Diaries ep. 010 #bendix #airbrakes kzfaq.info/get/bejne/o86JZMh00a2oimQ.html