Semi Truck Carrier Bearing Install

Рет қаралды 52,708

Honey River Ranch

3 жыл бұрын

Subscribe please! How to instal a Carrier bearing on a semi truck

Пікірлер: 24

@montymartin4493 5 ай бұрын

I always mark mine with a punch. It wont be out of time

@shanemicheal7848 3 жыл бұрын

I wanted to see u remove the old one :(

@richlymann6451 2 жыл бұрын

Should’ve put some anti seize on before the yoke.. Good Video

@narekhart9862 Жыл бұрын

Theres always one fag talking about anti seize lmao

@ricknieto9522 3 ай бұрын

😢😢thy

@narekhart9862 Жыл бұрын

Great video sir thank you

@LightSpirit24 Жыл бұрын

For goodness sakes, use a block of wood to hit the yoke. Every strike had me cringing. One wrong strike and the center threaded spindle would be buggered up.

@celso8325 8 ай бұрын

Putting it back on is the easy part smdh.

@vicpetrishak7705 Жыл бұрын

Please use safety glasses when air hammering the hard surface . 115/23

@Vater1 2 ай бұрын

Every time someone uses I torch I immediately rule myself out.

@tedcg20021 Жыл бұрын

by the way how's the socket size to remove the big nut? .thanks!

@KRuslan1000 Жыл бұрын

Socket- 1-5/8

@elviscastillo5437 2 жыл бұрын

I think i got this problem left my truck in a shop in alabsms but my question is what are the symptons when this piece is damaged? Regards and respect.

@HoneyRiverRanch 2 жыл бұрын

Drive shaft spins into power divider and truck goes nowhere

@HoneyRiverRanch 2 жыл бұрын

Sometimes you can lock the power divider in and get it to drive off the back rear end sometimes you can’t

@avandrosgulata9589 2 жыл бұрын

What the nut size

@franchescaready7075 2 жыл бұрын

What’s the Part number for that bearing ?

@joeybenton8986 3 жыл бұрын

You were doing good until you mucked up the nut a new nut and washer 12 bucks but you done to repair right.🤫🤫👌

@HoneyRiverRanch 3 жыл бұрын

70 miles from this shop to parts store we gotta make due from time to time

@endtimeawakening5557 5 ай бұрын

@@HoneyRiverRanch Exactly! When the parts store isn't around the corner, you have to use wisdom. Exercise some of that good old God-given common sense. ❤

@DieselTrucker2018 2 жыл бұрын

I took my 2016 International Lonestar into Petro of Deming NM today and they told me it would take 5 to 6 hours to change the carrier bearing and cost me almost $900!! I think this is a RIP-OFF!! Yes??

@HoneyRiverRanch 2 жыл бұрын

Yeah but that’s how repairs on the road go

@christopheryoung826 2 жыл бұрын

I've never had one take me more than 3 hours, and that was more due to ujoint issues. No way would it take 5 hours to replace a carrier bearing.

@TheAhuizar1990 5 ай бұрын

I got my coolant reservoir, carrier bearing, tensioner pulley, and water pump replaced for $437 . Your definitely getting ripped off