Great video.

why are you using 5v for rc from that place instead of hall cable? right or left

Pues gracias para tu lección de soldar hilos y de poner tubos termocompresibles!

Hi thank you for your initiave and effort to show us how to connect the RC receiver to the board. I'm wondering if you have another video with an example on how to connect 2 boards with the RC receiver! Again, thank you a lot!

I have seen a few different firmwares for the hoverboard. Please, what new firmware have you used? Could you put the link? Thank you.

after flashing, I connected my rc reciever like this, but it does nothing. I know the receiver works, cause I can connect up to a different project it works. when I turn on the hoverboard, I get a rising medly of beeps, instead if just a solid beep. if I just tap it on for just a moment it does the beeps, then the motors go forward and back a couple times then turns off. (a descending medly of beeps) any thought? how do I know the flash worked?

Hi i got a question i seen on auctions there exist 2 diffrent pcb boards green and dark blue of that board with one is better or newest?

hello firmware link plise ? dowload link + RC receiver link?

Is that set up for a ppm rc receiver?

So that first 4 pin connector he soldering is the wire that would connect directly to the rc receiver?

Will this doing steering as well ? Thanks

The hall sensor is 5v at 100ma max the UART I used is 5v at 30ma max I didn't want to overload the hall sensor wires.

Hướng dẫn nạp code với ạ

Hi... Did u modify the firmware? Or what

What happened to it though?

Hi nice video but sometimes hard to see what you are exactly doing. Do you have a drawling of the schematics and are you willing to send it to me and the community. Thanks.

Holla sou brasileiro

bjr pouvez vous me dire ou trouvez le firmware . merci d'avence

I need to calibrate the voltage meter on my hoverboard motherboard but im not 100% shore what they mean in the code. Do you know how to do it? // How to calibrate: connect GND and RX of a 3.3v uart-usb adapter to the right sensor board cable (be careful not to use the red wire of the cable. 15v will destroye verything.). if you are using nunchuck, disable it temporarily. enable DEBUG_SERIAL_USART3 and DEBUG_SERIAL_ASCII use asearial terminal. // Battery voltage calibration: connect power source. see . write value nr 5 to BAT_CALIB_ADC. make and flash firmware. then you can verify voltage on value 6 (devide it by 100.0 to get calibrated voltage). #define BAT_CALIB_REAL_VOLTAGE 42.0 // input voltage measured by multimeter #define BAT_CALIB_ADC 1654 // adc-value measured by mainboard (value nr 5 on UART debug output) #define BAT_NUMBER_OF_CELLS 10 // normal Hoverboard battery: 10s #define BAT_LOW_LVL1_ENABLE 0 // to beep or not to beep, 1 or 0 #define BAT_LOW_LVL1 3.6 // gently beeps at this voltage level. [V/cell] #define BAT_LOW_LVL2_ENABLE 1 // to beep or not to beep, 1 or 0 #define BAT_LOW_LVL2 3.5 // your battery is almost empty. Charge now! [V/cell] #define BAT_LOW_DEAD 3.34 // undervoltage poweroff. (while not driving) [V/cell]

Pode me qjudar

Ok,si eres mudo y no puedes hablar no hay estrés, como mínimo pone algo de musica ambiental!

After watching 20+ videos just hoping to find just one that actually shows the RC pin out connections, I really thought i found one here! NOPE. Out of focus, out of view, ZERO description of anything. Perfect example of how NOT to make a technical video.