No video
Shelly Plus 1 ESP32 Smart Relay | TASMOTA and Home Assistant
Рет қаралды 48,949
Күн бұрынIntegrating the new #Shelly Plus 1 and Plus 1 PM in wall relays with Home Assistant and optional Tasmota usage. The true local device! Tasmota templates and more below...
Shelly Plus 1 s.click.aliexp...
Shelly Plus 1 (Shelly Store) bit.ly/3qazTtY
Shelly Plus 1 PM s.click.aliexp...
Shelly Plus 1 PM (Shelly Store) bit.ly/3bG8Hej
⚡Tasmota Templates
Shelly Plus 1 Tasmota Setup (all one command/line below):
backlog template {"NAME":"ShellyPlus1","GPIO":[320,0,0,0,192,0,1,1,0,0,0,0,1,1,0,0,0,0,0,0,0,32,224,0,0,0,0,0,0,0,0,0,0,0,0,0],"FLAG":0,"BASE":1} ; switchmode1 2 ; Delay 1 ; Module 0
Shelly Plus 1 PM Tasmota Setup (all one command/line below):
backlog template {"NAME":"Shelly1PlusPM","GPIO":[320,0,0,0,192,2720,1,1,0,0,0,0,1,1,2656,0,0,0,0,2592,0,32,224,0,0,0,0,0,0,0,0,0,0,0,0,0],"FLAG":0,"BASE":1} ; switchmode1 2 ; Delay 1 ; Module 0
⚡Resources
Previous Garage Shelly Video - • Upgrade Shelly Switche...
⚡Products We Use/Recommend
Amazon US - amzn.to/2YZNDeO
Amazon UK - amzn.to/2TnG2R4
Amazon CA - amzn.to/2JWsNq5
⚡Be Social!⚡
Main Website - www.digiblur.com
Discord Chat - discord.digibl...
Patreon - patreon.digibl...
Join / @digiblurdiy
Facebook - facebook.digib...
Instagram - instagram.digi...
Please note, the product links above could be affiliate links, using them could earn digiblurDIY a small commission of most purchases and helps with future video projects. Thank you!
00:00 Intro
01:39 Shelly Plus 1
07:39 Shelly1 ESP32
10:14 Shelly Plus 1 PM
12:21 Shelly Stock GUI
14:19 Home Assistant Integration
16:34 MQTT is Broken
18:12 Closing Thoughts
@simfungreek 2 жыл бұрын
I used thin resistors legs for flashing. They do the job!
@Ernie-Tech 3 күн бұрын
Great vid and nice to compare them! If only Shelly would listen and act to customer's wishes. Everybody complains why Shelly firmware can't save a config to an external file. For backup, for documentation, for interchangebility, for experimenting. But no. I asked them in 2020 and still nothing changed. My main reason to go to Tasmota. Also completely opposite to this is that Shelly does prepair for firmware changes by implementing a pinheader!? So why not implement config save/restore? I really don't get it. I do like Shelly over Sonoff because of their better resistance against lightning/interruption peaks/dips on the mains. Lost Sonoff switches several times where all the Shellys persisted.
@jmr 2 жыл бұрын
Great video Digyblur and Great work Shelly!
@digiblurDIY 2 жыл бұрын
Thank you! 😁
@gmaclean1 2 жыл бұрын
Thanks for the video! I'd love to see your take on using Bluetooth with these devices and making it usable within home assistant with usage cases
@digiblurDIY 2 жыл бұрын
Have some footage coming up showing some BLE stuff on it.
@ronm6585 2 жыл бұрын
Thank you Travis.
@gadget1968 2 жыл бұрын
great job as always
@NickyNiclas Жыл бұрын
One thing that's extremely disappointing with the 1PM is how inaccurate the voltage reading is. I have 221V mains and it displays 205V which must mean that the power reading is inaccurate too.
@jwm1020 2 жыл бұрын
can you flash it ota like the older ones👍
@hond654 6 ай бұрын
Does anybody have experience with the life expectancy of HF7520 ( 6:56 in the video )? Depending on the frequency of switching eg 1/min -1/1hr is there any lifetime curve available for these? The reason is that I saw many faulty "smart plug" where the relay contacts were burnt after a year with about 1/hr switch rate.
@utubeanesh 3 ай бұрын
Thank you for the detailed video. Please let us know where is the antenna?
@digiblurDIY 3 ай бұрын
The wiggly trace on the end of the PCB
@patrickweggler 2 жыл бұрын
The pins are in the 50mil form factor.
@FredSchmitthammer Жыл бұрын
Will you do another video when esphome is supported? Perhaps steps to flash esphome on this switch?
@digiblurDIY Жыл бұрын
Esphome supports the esp32 solo chip now. You can even do a Bluetooth proxy with these now. I have the yaml on my website.
@paulfletcher2305 2 ай бұрын
I don't see anyone talking about the Access Point feature or the Range Extender. On the Shelly One Plus the AP is enabled and it will not let me disable it. It defaults to have the "Open network" box checked, but says "It is important to password protect your device's access point to secure your network from unauthorized access." If I uncheck the Open network box I can add a password, however it will not let me save the changes. To me this looks like a security risk. I have mine on a network that does not have access to my home network, but it seems like others could connect to the shelly and have access to other devices I have on that guest network.
@digiblurDIY 2 ай бұрын
I turn that off once I pair it with my network as I don't want open APs.
@MAD20248 3 ай бұрын
thank you so much for your awesome video , have you tried to flash shelly uni plus ? also will the shelly add on work with tasmota ?
@digiblurDIY 3 ай бұрын
Not really sure, I don't have one of those or the Shelly add on.
@horst36608 2 жыл бұрын
Does anyone know how to mount an external antenna? My 1+ is sitting inside a metal box and the wifi is shielded pretty well that way :(
@MAD20248 7 ай бұрын
have you tried the shelly plus add on, thinking of getting one to hardwire my door sensor and temp humidity sensor instead of this zigbee battery powered devices, would like to see a video
@digiblurDIY 7 ай бұрын
I have only tried the built in integration for them myself but I still prefer having full control of things with open source myself.
@theunderdog2205 2 жыл бұрын
Thanks
@cybermodstudio9380 2 жыл бұрын
感谢分享，我居住在中国，但是不好买到Shelly设备
@RyanLangu 2 жыл бұрын
Did you have to do anything special to enter flashing mode, like grounding the GPIO-0 pin, or holding the button?
@digiblurDIY 2 жыл бұрын
GPIO 0 to ground just like a regular ESP32
@diogomorgado9310 2 жыл бұрын
How did you flash tasmota? I'm having a hard time getting the chip ready for flash. Do you have to ground I0-0? I tried but still doesn't work.
@digiblurDIY 2 жыл бұрын
What flasher is being used? Some do not have enough power.
@bhaumiksoni2009 2 жыл бұрын
when internet goes off thee shelly resets the time and puts it to 0:0 AM how i can persist the time ?????
@digiblurDIY 2 жыл бұрын
Point it to a local ntpserver on your network if you have issues with internet outages.
@djashjones 2 жыл бұрын
I wonder if it support thread or matter in the future?
@digiblurDIY 2 жыл бұрын
Thread will be zigbee so I'd say no.
@evlicocukluoyuncu 2 жыл бұрын
hello, can I use this device to change the direction of the AC signal? I have an electrical Velux, and I need a switch that will help me to change the wiring in order to open and close the Velux accordingly... I do not know if you fully understand what I need, but I really hope to find the correct product for my need here :)
@evlicocukluoyuncu 2 жыл бұрын
In other words, can I use this Shelly Plus 1 as a DPDT rocker switch for reversing the AC signal that feeds my Velux... ?
@digiblurDIY 2 жыл бұрын
Sorry not familiar with those myself.
@michaelferrin2688 2 жыл бұрын
Call me dumb, but.....what are the uses of the Bluetooth on the cip? What can you do with it?
@digiblurDIY 2 жыл бұрын
For stock usage it is great for pairing to a network as it removes the issues of dual band isolated same SSIDs. For after market... All kinds of cool sensors.
@mdkz4226 2 жыл бұрын
What do you say about the temperature when the relay is on? Compared to shelly 2.5 and 1pm in the original firmware?
@digiblurDIY 2 жыл бұрын
I haven't compared the original firmware as I don't run it.
@mdkz4226 2 жыл бұрын
@@digiblurDIY Ok, then in comparison with the non-original firmware, what can you say about the temperature? 😊
@kflott 2 жыл бұрын
I'm looking at your pinout and the order looks like it is almost the same as my USB ftdi module, I'm wondering if those pins would fit directly in those holes.
@digiblurDIY 2 жыл бұрын
Need some super small pins. Even breadboard jumpers were a tad big, dupont is definitely a no go.
@AmiApache 2 жыл бұрын
@@digiblurDIY Maybe a bobbypin or similar? Safety pin-mod ?
@dc857 9 ай бұрын
No they won't they are too big on mine. I had to buy a 1.27mm pitch pin header. The pins are 0.4mm square and they fit. Painful to solder, at least for me.
@Liv3_fps 2 жыл бұрын
Can the Shelly 1 or 1PM be triggered to turn on/off the relay over the GPIO ports?
@digiblurDIY 2 жыл бұрын
I know it can be done with Tasmota firmware
@Liv3_fps 2 жыл бұрын
@@digiblurDIY yeah i actually found a video of someone who was able to make it work via Tasmota firmware after I left this comment. They did it by using a light switch to open and close a loop between Ground and GPIO-3 pins of the Shelly 1 to turn the relay on and off. It took many hours of searching to find that information so I hope it helps someone else here!
@digiblurDIY 2 жыл бұрын
I did it way back in my original Shelly tips and tricks video. If you use mains power on the device you do need to use a mains rated switch to isolate things.
@Liv3_fps 2 жыл бұрын
@@digiblurDIY for my situation I am trying to control the Shelly relay using a Raspberry Pi Zero, so I can't do it via AC power. I am trying to control the relay using the Pi's 3.3V or 5V port and a GPIO port.
@Liv3_fps 2 жыл бұрын
@@digiblurDIY not sure if this would work to connect 3.3V and GPIO port from the Pi to the Shelly Gnd and GPIO3 port for controlling the relay on/off.
@Thamli 2 жыл бұрын
That 1PM+ might short out. On that PM chip the bottom left pins aren't soldered cleanly enough. Check it!
@digiblurDIY 2 жыл бұрын
On the BL0937 itself?
@Thamli 2 жыл бұрын
@@digiblurDIY yes, check minute 11:55 . Bottom left 2 pins of the BL. Seems to have some solder almost bridging both pins.
@ingy23 2 жыл бұрын
Good spot
@KaidoLP 2 жыл бұрын
On the regular one there also is a solder bridge on the topside of the ESP
@pstoianov 2 жыл бұрын
Before flashing to Beta, first test the device...
@digiblurDIY 2 жыл бұрын
I did. It's not hard to flash back as well or even to Tasmota. I took backups of the original firmwares as well.
@Rilnaista 2 жыл бұрын
@@digiblurDIY Hey, can u please make a short video on how to flash them? I tried to get it working, but everytime I try it doesn't work. I use the pinheaders to connect an ftdi32 - perhaps i connect it wrong - don't know ... would be nice to get a video. There is no other video on youtube for the plus series. thank you!
@digiblurDIY 2 жыл бұрын
FTDI might not provide enough power for the esp32 to go into flash mode.
@spok01 Жыл бұрын
@@digiblurDIY do you not have pulled down the PU Pin to go in flash mode?
@digiblurDIY Жыл бұрын
GPIO 0 pull down is still the normal.
mostlychris
Рет қаралды 49 М.