First

Nice work matey, now hunting for a scrap fridge!, i need a quieter compressor for winter, so i can air-brush indoors..im not freezing my arse off in my workshop!!Lol!. All the best.

Very Good build. Exactly what I was looking for. Thank You!!!

Bro... Fantastic job! Looks great and works really well!

Love that rooster in the background who started so many times but barely had a chance to finish :)

Once the galvanic corrosion depletes the threads on that check valve, you will have a 100+ psi bullet with a HUGE potential to kill someone. Imagine sitting down on the ground to drain the water when it flies off into your eye. Given there is no rifling, no containment, that screws shape, and the pressure exerted on it, the potential for it to tumble is high. So it enters your eye, and hits your brain. Caskets are more expensive than proper air compressor parts. Engineering your own parts is one thing, but not when it comes to pressurized loads. Most people do not realize that little things such as using dissimilar metals can cause catastrophic accidents. Do not solder -- braze it. Do not weld the tank unless you are a professional welder. Fill the tank with water, drain, then dry; Don't weld a tank full of water. Match the maximum working pressure (derate it by at least 20%) of the tubing (look it up from the manufacturer given the diameter) to the check valve you intend to use.

Very well presented and executed good job.

Again you surprise us your machines, they are very easy to make. Greetings from Colombia

Very nice video.......and big respect from Zagreb/Croatia

I just love all the safety gear

Amazing Compressor creation 👍👍👍

Well done, very nice and great finished look. For next build, you do not need a oil drain plug in the bottom of the compressor. All the oil in the compressor ends up in the bottom of the air tank, so you need plug there. To add new oil to the compressor, just dip the inlet tube on the compressor in a cup of oil and it will suck it up happily :)

еще фильтр добавить на входящею трубку, что бы пыль не набиралась в компрессор, а в целом получилось хорошо)

Ha ha ha ... Very creative. I want to develop it into a PCP pump. Thank you for the information.👍🙏

Great craftsmanship.

That’s absolutely adorable❤

Very good your compressor my friend, I'm crazy to ride mine too.

It’s amazing how much pressure one of those motors will produce. My dad made one with the motor out of an old freezer. He had a big tank and set the high limit to 300 psi. He set the pressure back down when he blew a low tire off the rim. He was lucky not to get hurt. 😀 They are slow to build pressure though.

This is the best one I’ve seen

At last you done good use of yours underware for wipe compressor oil good skilled man 😁😎👏🛠⚒🔨🔧

Welding in flipflops and wool gloves. Guys a genius!

Te quedó excelente, mis felicitaciones.

Esta muy lindo y funcional el proyecto, debes ponerle a trabajar el espiche del aire que queda en el tramo del tubo de salida del compresor, asi ayudas a evitar que toda la presion de aire del tanque una vez que el compresor alla alcanzado la presion de llenado que hayas fijado en el presostato la reciba el flaper de alta, tienes la opcion solo que le pusiste un tapo, ella va con una manguera de la valvula antiretorno de tres vias a la parte de abajo del presostato. Yo hice uno pero con un compresor de aire de 15.000 btu, de botella, lo que no me gusta que igual estos tipos de compresores escapan mucho aceite salida, y a su vez llenaran el pulmon. Saludos..

I put a 1hp compressor onto a 50 litre tank.replacing a broken "rattler". Perfect.

Grat video man left a like keep up

I gave this a thumbs because I think this guy was welding naked at one point lol n the sound effects made it

The word "explosive decompression" comes to mind when looking at those welds.

very good work

Very cool well done.

Excelente los compresores de aire.con la bocha de heladera . impecable los trabajos abrasos

Nice video and actually gumawa din ako nyan (I get the idea on this video) di nga lang kasing ganda ng sayo. Thanks for making this video

Prima Arbeit!

nice job man

Clean work design

Really great idea ;) like!

Also a Filipino DIYer here! Amazing works!!!

you got the active and neutral arse about on the switch, input side. Nice welds bro!

Idol ka talaga sir!

ang galing talaga ng Pinoy!

that last wiper is awsome hahaha

Very good job, When you introduce us to the sound effects (rooster) Sek :)

Beautiful..!!!

love yaa deadly winter gloves for welding

"Angas nyan kuya ah" hahahahaha awesome project, from dasma, cavite

Wow amazing.

what size thread is required for the T check valve socket? is the 1/4 reducer NPT or BSP? and where do you get the extension ro mount between 1/4 reducer and pressure switch?

I thought you needed a start capacitor when using sealed units. Can someone explain this to me please

Nice, Sek this is cheap & easy to build in my place ( i will made like you video) thank's a lot sek, keep roll with new video other device.

parabens servico de mestre..

Bahut bdhiya good luck video

Conception is really good and the work too but if u want to use it for something else then for airbrush that has to low power and if u'r using this for airbrush u don't really need such big tank u can instead use old fire extinguisher or CO2 tank from this wierd home sodifiers but the work what have u done is really good

Thank you for this video. i cant find the 1/4 reducer and the 1/4 copper tube connector from Aliexpress. Can you share the link were you bought yours? thank you

Lajkčina!! Danke für uploading.

Как всегда ЛЮКС !

Uy unang ambag sa pinas nagustohan kotong compressor nato maganda to para sa shop namen😄

extreme make. ayos yan para sa industrialization ng Pilipinas.

NIIVELL DEU !! LEVEL GOOD !! NIVEL DIOS !! UN CRACK !!!!!!

Thanks for your video….yours was one of the first that caught my attention and got me interested in this. Since then I’ve made a number of these compressors for others (from used, broken, craigslist, and dump-finds with Porter Cable, DeWALT, Craftsman, Campbell Hausfeld, Huskey, Bostich, and Central Pneumatic tanks (2 gal to 20 gal)). ALL working great (and none having experienced temp overloads filling from empty- which surprised me on those greater than 8 gal). TWO OIL DRAIN-FILL QUESTIONS (answers will help not only me,but all others making these units) (1) With a refrigeration compressor with 1 pressure tube and 1 inlet tube (assume “without” any manufacturing installed crimped Freon fill tube) I’m having trouble draining/filling oil (while tilting compressor towards the inlet tube) due to "either", various bends in the inlet tube, OR due to no air escape route while draining. Any suggestions how to drain/fill with only 1 inlet tube (2) If there are no answers to (1) above, I assume a last resort might be to drill a hole in the compressor and Braze a fitting into the hole (that can be capped or plugged for drain/fill). Can this be done with a Bernzomatic TS8000 torch using Mapp gas? Issues are not knowing what's on the other side of where you're drilling; getting chips into the compressor while drilling; heat having some bad affect inside the compressor while BRAZING. Thanks.

I like your welding bro

muito bom ficou muito lindo tambem parabens

Galing tlaga ng gwang pinoy..

Thanks, a wonderful idea

Maravilhoso trabalho amigo.

There is oil vapor heavily coming out of the compressor actually, so you need to separate it and lead it back to the third (sealed) pipe end coming out of the compressor, because that is where it has originally been filled with gas and oil. The oils they use in these compressors are mostly synthetic ones (e.g. polyolesther) and they cause irritation with skin and lung contact, so you should keep that in mind. Cheaper (like noname chinese) compressors have very thin, waterlike oil in them, expensive ones (like Danfoss) have thick and yellowish oil. I have just disassemled a few of these, and used one to make 4bar in a vessel, but I think it may also be suitable for painting compressor, however, you need to carefully lead back all the oil to the compressor.

Good job indeed 👍👏👏👏bravo

I love this!! Welding with grandma's gloves in flip flops. Either Mexico or China. Although both are the same just smell differently. However, TRULY silent air compressor. These in the US that utilize fridge pumps are still around $1000.

Great build😊

Una observación como sugerencia es que tienes dos tubos para la entrada de aire en uno le puedes adaptar un filtro de motocicleta para gasolina (purificar el aire) y en el otro poner una boquilla con una tuerca cónica cuerda interna con tapón para agregar el aceite ademas en la salida de aire del manifould ponerle un filtro para retención de agua y aceite. pero en si es muy bueno tu proyecto felicitaciones.

Is there a way to do this without welding? I have zero experience in that. I do need a quieter compressor however

at the end of the video, clean the oil of the screw with some underpants?

Will be great for my airbrush! Thank you.

Your rooster sounds very funny at 1.5 playspeed

Es cierto que cuando usas un motor frigorifico para hacer un compresor de aire, es mejor ponerle aceite 10w40, en vez del aceite que lleva?

Thank you for sharing ,nice job! but you have to handle the problem that there is lot of refrigeration oil go into the gas tank, otherwise the pressure air come with oil.

Superb :)

Can I use an AC compressor? You drained the oil and replace, what kind of oil?

astig sir.... makatry nga

very nice

thanks bro

Saludos cada cuanto tiempo hay que cambiar el aceite para sacar e agua del compresor y no sufra daños?

another well deserved repurpose. keep it coming.

VERY GOOD

Great project! Why did you change the oil? Is it necessary to install a valve to change the oil?

Fiz com motor de ar condicionado 10 BTUs, reservatório de extintor, coloquei todos intenso de segurança ficou top. 120 psi.

Mate you're awesome. I almost feel like a slacker, as I have some, probably most of, the tools that you have, and I don't do anywhere near what you do with them. I saw you build a scroll saw, make a nibbler, a compressor, and I'm sitting here looking on eBay for ones to come along. I'm 38 and only ran my first bead of stick weld last weekend.

Awesoooomeeeee!!!! 3thumbs up!

Me encantan los zapatos de protección jajajaja. Felicitaciones excelente

Very nice

Regards .. How long does it take to change the oil to remove water from the compressor and not be damaged?

boss tanong lang po , ilan minuto kaya mapuno ung air tank mo..palagay ko mejo matagal yata..???

The problem with this compressor you used is that the flow is unfortunate, but I found the oil drain interesting.

hello i have a question how to used an ac compressor with the help of an electric motor to transfer lpg gas to a lovato gas tank?

Nice video

Bonjour très bonne idée en plus j'ai vu que vous avez mis une vis de vidange d'huile et une de remplissage, ma question est la suivante, combien d'huile remettez vous en tout ? Merci

. 'Silent' be like a fridge running permanently, nice job keep at it fridges are noisy when trying to sleep

Need to dump the refrigerant in the air compressor?

Thanks for a very useful video. But can u tell me how to set min & max pressure? Thank you!

Magnific machine 👍👍🇧🇷🇧🇷

exelente video saludos desde sinaloa mexico

*Whether or not it is used for PCP air guns* 🤔?? Please reply