Silicone Render day three

No video

Silicone Render day three

Рет қаралды 13,618

Work life

Күн бұрын

Silicone render job applying the backing render

Пікірлер: 37

@kellypender8136 2 жыл бұрын

Really enjoyed watching these. Good job guys!

@Ireland-bc2gx 9 ай бұрын

The notch trowel not needed,the better the mesh and base coat the better the finish will be,the primer is key ,and tinted To the finish colour

@worklife4221 9 ай бұрын

Totally disagree this is how we were taught to do it when we did the course and it works for us and we get a great finish

@Trekz86 20 күн бұрын

You should fold the mesh into the internal corners

@Happytruth Ай бұрын

Hi I noticed you used a primer on the bricks presumably this is for a key and to even up suction and do you have to use a primer on all block and brick substrates? Can you also spray that base coat rather than hand apply and just flatten off?

@rockgsxr 2 ай бұрын

the speedskim finish on the basecoat, is it enough key for the topcoat? good job btw. I done some k rending years ago in London, been out of the loop for a while but got my first silicon job coming up

@worklife4221 2 ай бұрын

Yes the speedskim does the job just get it as flat and smooth as possible cause if you don’t it will show when finish is put on, hope all goes well for you

@durexjim 2 жыл бұрын

so far so good

@kaimichael5444 Жыл бұрын

Hi do u not put 2 coats of render on. Ie mesh coat then coat on top of mesh just skim coat. Looks really well though ladds

@worklife4221 Жыл бұрын

Just one coat of the base coat and then the mesh and use the notched trowel to bed the mesh in and then flatten, also use more render to fill any low spots when flattening

@rayking507 Жыл бұрын

After the base coat sets what happens if it rains and the base coat gets all wet. Will it be ok once the base coat dries back up. Many thanks.

@worklife4221 Жыл бұрын

The base coat will usually get hard enough that it won’t effect it but as a rule when doing any outside work like rendering or bricklaying etc always check the weather and be a 100% sure that it’s going to be dry.

@johnny6722 2 жыл бұрын

Starting to look good mate. Can I ask where your buying the materials from. Thanks john ps as I can only find Webbers and K render at my local Selco.

@ipfishing1466 2 жыл бұрын

Thanks bud I get my silicone render supplies at MKM building supplies in Chelmsford Essex I assume other branches supply it as well but you would have to check hope this helps you.

@ZAFPS 9 ай бұрын

Hey mate doing some of this soon thinking of getting 5mm beads is this what you used?

@worklife4221 9 ай бұрын

Yes mate they were

@DanielWilkinson-uk5wo Жыл бұрын

Do you sponge your basecoat to remove spatula lines once ruled flat?

@worklife4221 Жыл бұрын

Yes you can go over it with a flat sponge float refina do a good one just make sure it’s the right consistency before sponging it shouldn’t be to wet.

@DanielWilkinson-uk5wo Жыл бұрын

What sort of time are you finding to sponge?

@worklife4221 Жыл бұрын

@@DanielWilkinson-uk5wo it all depends on temperature so basically if you can poke your finger into it then it’s to wet

@Sebastian-py7qo 6 ай бұрын

Chłopaki się nie spodziewali że właściciel ma oświetlenie pod w podbicie Dachu poszli na wieczór podziwiać jak jest zrobione i byli w szoku jakie Garby Właściciel dodał na Gogle po zakończeniu pracy zdjęcia 😂 Mimo wszystko dobrze się ogląda 😂

@ipfishing1466 6 ай бұрын

The owner is an idiot if you put lights directly onto a wall like that it’s always going to show and we told him this from the start we told him that the existing wall would have to be flattened but he wouldn’t pay for it