No video
Silverado NBS (99-07) 4 Piston Brake Upgrade using 2020 Silverado Parts
Рет қаралды 33,516
Күн бұрынFinally upgrading the front brakes on the truck. Using parts from a 2019-2020 silverado/sierra. Pretty east except for the part where you have to center the new caliper.
Subscribe, like, comment some shit. I’m planning on recording every time one of cars break or if I plan on modifying them somehow. Will also post updates and future projects here. Currently own a s14, 350z, silverado, and a FD.
You are messing with your brake system so if you don’t know what you are doing take it to a professional. I’m not responsible if you hurt yourself or others. I’m not responsible if you damage your vehicle or any other property. When you work on your vehicle it’s AT YOUR OWN RISK
I’m not some certified master ASE mechanic. I just like working on my cars. Always do your own research before working on your vehicle. If you don’t know what you are doing take your car to a professional shop. Exercise safety procedures when working on or near vehicles. I’m not responsible for anything that goes wrong with your car or any injuries you may obtain.
This video is intended as entertainment only.
THANKS TO THE FOLLOWING AND CHECK THEM OUT ON IG
Intro video credit IG @samalamajo • “Sidewalk Scrapers" by...
Outro photo credit IG @dutch_touch
I DONT OWN THE MUSIC
red nation- the game
@44hawk28 Жыл бұрын
If you have the caliper on the wrong side and the bleeder screw is on the bottom, it can not be bled properly. If you get done with the job and your pedal is noticeably spongy, that means it still isn't bled completely. I'm currently looking into see if this upgrade can be done on a 2008 model. It may require slightly different Hardware. But I do like this upgrade. The torque spec on those caliper bolts is 120 ft lb. I believe on the banjo bolt it's about 20 to 25 ft pounds. And you are supposed to use new copper washers each time, but if you're very careful you might be able to skate by with using them one extra time.
@sanjuan240 Жыл бұрын
I was able to bleed it properly and thanks for the torque specs. My truck is sold now and I never had issues with it since I installed these calipers
@garybensel6680 2 ай бұрын
Biggest problem is the factory wheels hit the new calipers so now you will need 1/2” spacers and longer wheel studs. Note easy to find. You will need an old stud to measure to find a new set.
@sanjuan240 2 ай бұрын
Depends which wheels because wouldn’t the stock wheels of the 2020 trucks clear since that’s what they came with
@86Chevymontecarlo 5 ай бұрын
I did this upgrade about two years ago. FYI If you have a set of 17" Vision legend 6 like me those brakes will actually fit with a decent amount of clearance between the inner rim and caliper to my surprise.
@sanjuan240 5 ай бұрын
I was going to try and pin more then one comment hopefully
@sanjuan240 5 ай бұрын
Good info
@54inches 3 жыл бұрын
Very well explained, young man. Great job!
@sanjuan240 3 жыл бұрын
Thanks
@sanjuan240 3 жыл бұрын
For the washer required to shim the caliper I would start with 1/8 or 0.125 THICK and see how it looks on your truck. That seems to be the size that came up a lot when I did my research. Currently on eBay as of 8/15/22 www.ebay.com/itm/334502377762?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=Yl6wBEtQT_S&sssrc=2349624&ssuid=Qix07Az6Sie&var=&widget_ver=artemis&media=COPY
@LoPhatMelk 3 жыл бұрын
4mm of shim space is optimal, no more than 5mm from what I've seen.
@chitos2132 5 ай бұрын
Can’t find any on eBay or a junk yard here so ima have to buy a kit for an 800 but it’s a solid upgrade with drilled and slotted z23 kit
@sanjuan240 5 ай бұрын
Nice even better probably
@fernandoescobar5236 3 жыл бұрын
Nice video just received one of the calipers from summit waiting for the other to do this swap.
@sanjuan240 3 жыл бұрын
Thanks. Btw if you don’t like brake dust on your wheels i would go with a different brand of brake pads. The ones I chose are dusty maybe try another brand.
@fernandoescobar5236 3 жыл бұрын
@@sanjuan240 i was checking rock auto and might stick with the oem ones until my go to brand Akebono makes some pads for it
@Mlo713 3 жыл бұрын
Nice truck! You should make more videos of your truck. 👍🏽🔥🔥🔥
@sanjuan240 3 жыл бұрын
Thanks man. I will try have a couple other projects as well
@spyderlyf3 3 жыл бұрын
It would've been a lot easier to just reference the center line on the caliper. Much easier to see how it should center on the rotor rather showing the space where the pads go. Helluva upgrade either way and thanks for the vid..
@sanjuan240 3 жыл бұрын
That’s one way to explain it. In my head I already knew what I was doing but trying to explain it in a easy way was kinda hard for me.
@garybensel6680 9 ай бұрын
Prices today are much higher if you can find them, also it should be mentioned that the stock rims will not fit these calipers. Factory stock 16” and 17” will not work, probably 18s might but I’m looking for 20” rims which are hard to find in junk yards so this upgrade will probably be over $2,000 if you include new rims and tires.
@sanjuan240 9 ай бұрын
There some sets on eBay right just checked. One for 360$ obo. Some rotors for idk 200$ you at 560. Without wheels obviously
@My65isblack 5 ай бұрын
I have 20 inch rims for sale? Am asking $500 there KMCs
@garybensel6680 2 ай бұрын
@@sanjuan240yes, wheels and tires are pricey
@NuckleHead714 3 жыл бұрын
This my sound silly but did it actually improve braking I heard that you might need to change the brake booster also to accommodate the bigger calipers but I’m not so shur
@sanjuan240 3 жыл бұрын
I definitely felt some improvement. Maybe just make sure you have the same rear caliper as me. Some come with 2 pitons I believe which might cause a difference since you would now be pushing more pistons total.
@musclekingmedia 3 жыл бұрын
Booster has no affect. Only the master cyl would need to be either swapped or you can run a proportioning valve to change the bias a little.
@joerivas9847 Жыл бұрын
Im glad you pointed out the safety issue. Respect to you. I have seen more than one of these videos where, IDIOTS dont use them. Gamble in Vegas, not with your life!!
@sanjuan240 Жыл бұрын
Yeah same and these trucks are heavy haha
@alexrebollar4686 8 ай бұрын
Clean ahh wips
@sanjuan240 7 ай бұрын
Thanks man!!!
@ninorodriguez1547 3 жыл бұрын
Hell yea been waiting for this one...lol
@MrCluster817 3 жыл бұрын
Nice truck and great video bro👌, Hey do you know exactly the kind of washers you bought from ACE I’m thinking about doing the same upgrade on my 04 Silverado.
@sanjuan240 3 жыл бұрын
So just make sure the bolts goes through it. My research said 1/8 or 0.125in THICK. I would start with that and see how it looks on your truck.
@gonzoxx8413 3 жыл бұрын
Nice video bro. Do you have any plans for hydroboost conversion? I would love to see a video explaining it.
@sanjuan240 3 жыл бұрын
Eventually might have to depending on my wheel/height setup I want.
@fouledout443 3 жыл бұрын
Awesome man, im about to do the same on my truck!
@sanjuan240 3 жыл бұрын
Dope. You will definitely notice a difference
@dylansmith3 Жыл бұрын
@@sanjuan240 is there a 2 piston caliper upgrade for the rear for our trucks?
@sanjuan240 Жыл бұрын
@@dylansmith3 I believe so yeah from a newer year possibly 07 but not 100% sure
@chatobalencian1504 6 ай бұрын
Thanks for vid also what kind of drop did u put on your truck and what tire size looks bad ass 👌👍👍
@sanjuan240 6 ай бұрын
4/8 drop with 265/35
@Jaydayallday 2 жыл бұрын
Good vid good info. Looks sick
@sanjuan240 2 жыл бұрын
Thanks man!!
@Jaydayallday 2 жыл бұрын
@@sanjuan240 do you have link for calipers? Searching and can’t find them.
@sanjuan240 2 жыл бұрын
@@Jaydayallday i got lucky and found mine on eBay of a wrecked truck. You could always go down to the dealer ship and buy them new if you can’t find any at the usual stores
@rafaelrosas2918 2 жыл бұрын
Nice video very well xplained
@sanjuan240 2 жыл бұрын
Thanks
@rafaelrosas2918 2 жыл бұрын
@@sanjuan240 hey i cant find the rotors it has to be 4 pistons or is the same as 2 pistons
@sanjuan240 2 жыл бұрын
@@rafaelrosas2918 I would try and find the 4 piston ones. Last case scenario go to the dealership
@rafaelrosas2918 2 жыл бұрын
@@sanjuan240 thank u
@johnclintonmusicandmore 2 жыл бұрын
good video thank for part #'s that will help and good job emphasizing the use of jack stands 1/2 the people on youtube don't use them
@sanjuan240 2 жыл бұрын
Thanks man. I’ve heard to many stories of not using jack stands
@eddieschopshop 2 жыл бұрын
great upgrade for the price.. what was the size of the 2020 rotors.. 13" or 13.5"
@sanjuan240 2 жыл бұрын
13.5 I believe. Definitely noticeable difference and worth it
@travishotard9490 3 жыл бұрын
Hell yeah bro might do this soon 20s should be good
@sanjuan240 3 жыл бұрын
Dope bro!! 20 should work
@1980prostreetcutlass Жыл бұрын
U need to upgrade the master cylinder to
@sanjuan240 Жыл бұрын
I did not and brake pedal feel fine
@1kbutta 3 жыл бұрын
Do you have to upgrade that master cylinder? Thanks for the vid
@sanjuan240 3 жыл бұрын
I did not. As long a you have the same brake set up I have I don’t think you have to. The pedal feels fine.
@MrMaddparkison 2 жыл бұрын
What about at a hard stop. I've seen some videos where people are saying it doesn't "lock up" like the factory setup. Like the hard chirp when the abs kicks in.
@banga8080 3 жыл бұрын
👍🏾👍🏾👍🏾great vid bro
@sanjuan240 3 жыл бұрын
Thanks man!!
@dougsweldingfabrication953 2 жыл бұрын
Can you give me part numbers? When I pull up 2020 Silverado front Calipers, they are just 2 piston standard calipers. What are the specifics?
@sanjuan240 2 жыл бұрын
I don’t know part numbers but if you type in “2020 Silverado calipers” on Facebook market place there are a couple people selling some. OR there is a set on eBay currently www.ebay.com/itm/334502377762?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=Yl6wBEtQT_S&sssrc=2349624&ssuid=Qix07Az6Sie&var=&widget_ver=artemis&media=COPY
@My65isblack 5 ай бұрын
@@sanjuan240yo link doesn't work
@sanjuan240 5 ай бұрын
@@My65isblack bro that was like last year haha. Them shi probably sold lol
@My65isblack 5 ай бұрын
@@sanjuan240😂😂😂damn video doesn't look old 😂
@LoPhatMelk 3 жыл бұрын
Did you leave your dust shields on?
@sanjuan240 3 жыл бұрын
Yes I did. If yours are different then mine I’m sure you can clearance them a little
@GDG184 3 жыл бұрын
Tried looking for calipers and rotors on autozones app for a 2019 silverado and a 2020 silverado and it's getting me floating dual piston calipers am I missing something or using the wrong model? Where can I get these upgraded parts at?
@sanjuan240 3 жыл бұрын
When I was gathering parts I came across the same issue. That’s why I went and searched eBay. You can buy them new from the dealership but they are expensive around 180$ each. The “ac delco “ part numbers are 172-2883 173-2882 Last I checked they were out of stock.
@sanjuan240 3 жыл бұрын
Rotors are from “advance auto parts” with the part number I show.
@GDG184 3 жыл бұрын
@@sanjuan240 thank you the the info I'll have to be on the hunt for them
@xforce687 3 жыл бұрын
The calipers are technically floating. The bracket from the original setup isn't re-used. These are like the performance car design, or most Toyota calipers up front.
@carloswiener3708 3 жыл бұрын
Order them online I paid 80 something per caliper
@cesarlopez2672 2 жыл бұрын
Do you know if you can upgrade the rear with the same 2020 brakes awesome i upgrade btw
@sanjuan240 2 жыл бұрын
I’m not sure on that honestly. But someone let me know that the dealership install big Brembo front calipers on the 2020. So if the stock ones fit 99-07 then those Brembos might fit too.
@cesarlopez2672 2 жыл бұрын
Oh okay cool ima look into it and everyone talks about the front but no one mentions the back so I was curious if you knew
@1ruckus1 2 жыл бұрын
@@cesarlopez2672 rears will not work, there electric or the e brake is electrict, but from what I heat if your rear is a single piston you can upgrade with 07+ double piston caliper and bigger rotors
@ericmercado 3 жыл бұрын
hi i just get some calipers and disc from a GMC Sierra 2021 its the same like this? also can i still use the OEM Brake pads
@sanjuan240 3 жыл бұрын
As long as they look the ones I used then yes they should work. I’m sure you can use the oem brake pads of the Sierra.
@CarlosGarcia-wg6cv 3 жыл бұрын
What’s the lowest rim offset ?
@sanjuan240 3 жыл бұрын
That will work with these calipers? I’m not sure I’m going to say whatever the 2020 Silverado came with stock.
@ndttech 3 жыл бұрын
Would you be able to replace the entire knuckle and not use any washers?
@sanjuan240 3 жыл бұрын
Maybe would depend on how different the knuckle between those years are. The mounting holes might be a little off. Of the they give you a different turning radius. So I’m not sure on that
@dylansmith3 Жыл бұрын
What’s the rotor part number?
@sanjuan240 Жыл бұрын
I believe I showed it when I filmed over the parts. I don’t remember honestly
@89Jeeper Жыл бұрын
🤔 wonder if these upgrades would work on my 06 GMC Sierra 1500HD 6.0ltr, my drive line is the same as a 2500HD ..
@sanjuan240 Жыл бұрын
I think someone in the comments said he was going to try it out. As long as everything is the same as a 1500 I don’t why it wouldn’t work
@89Jeeper Жыл бұрын
@@sanjuan240 well my rotors are the same as a 2500HD, the only thing like a 1500 is my frame. Factory 1500HD
@chrisbrown-hc8nf 3 жыл бұрын
Do you have the part number for the brake callipers
@sanjuan240 3 жыл бұрын
172-2883 173-2882
@sanjuan240 3 жыл бұрын
Those are ac delco part numbers but I believe they are out of stock
@jdavisfabrication2401 Жыл бұрын
I want to do the upgrade on the rear
@sanjuan240 Жыл бұрын
I haven’t done it personally but I’m sure someone has
@Tool-Meister 3 жыл бұрын
I tow HEAVY with my 07 Classic 2500HD Duramax. I want to upgrade rotors and calipers on all 4 wheels. Any tips or suggestions?
@sanjuan240 3 жыл бұрын
I mean if it’s 6 lug I don’t see why the same upgrade I did on mine wouldn’t work. If it’s 8 lug I believe someone else In the comment section was trying to see if this swap would work on his truck.
@sanjuan240 3 жыл бұрын
I believe he mentioned that caliper stock for stock are different from a 1500 so that would mean this probably wouldn’t work without some custom work
@albertgibbs2937 3 жыл бұрын
I run PowerStop pads and rotors on my 2004 2500hd with Braided steel brake lines and a 2011 lml brake booster. Definitely a game changer form the stock brakes. My truck will put you through the windshield stopping from 120 mph on the drag strip...
@baysideexteriorwashing7719 2 жыл бұрын
Dose this kit also work for the back?
@sanjuan240 2 жыл бұрын
Not that I know of. I personally haven’t dug too deep into it though
@jeremywilson1299 2 жыл бұрын
On the back most use the same year models Like 99-2002 Tahoe rear brake calipers, rotors,also suburban, Yukon works. they are bigger and dual piston from factory instead of singe piston Can even use newer 07-14 rear setup Off the vehicles that have disc instead of drums.
@odiarroyo6144 3 жыл бұрын
There is your👍 and ur Subed! My butta!! Kip up the good teaching
@sanjuan240 3 жыл бұрын
Thanks man!!
@oscarmagana1880 Жыл бұрын
Is this set up will work on a 2004 Yukon denali awd ? Do you know
@sanjuan240 Жыл бұрын
That I don’t know honestly
@Adanchavez52 3 жыл бұрын
still working good??
@sanjuan240 3 жыл бұрын
Oh yeah they definitely make a difference. Only thing is this particular brand of brake pads are a little dusty. Maybe try a different brand or OEM pads. But still good easy upgrade
@Adanchavez52 3 жыл бұрын
@@sanjuan240 awesome thanks for the reply 👍 cant wait to do mines
@pwrtow8 3 жыл бұрын
Are these calipers aluminum or steel?
@sanjuan240 3 жыл бұрын
I want to say cast iron they definitely got some weight to them
@pwrtow8 3 жыл бұрын
@@sanjuan240 Thank you- I guess I'll have to paint them so they don't rust!
@chevyboiii2115 3 жыл бұрын
So is this upgrade only for the front or for all 4 wheels 🤔
@sanjuan240 3 жыл бұрын
Only for the front that I know of. I haven’t seen or heard of anyone do it in the rear.
@MrMaddparkison 2 жыл бұрын
You can swap the single Piston rear caliper to a double piston. That's what I'm going to do. But I have hydro boost on mine
@JoseContreras-mv5yz 2 жыл бұрын
I got the calipers and mocked it up to the spindles with the hubs on but it looks like i need an inch or even more to center the caliper to the rotor area. Am i missing something?
@sanjuan240 2 жыл бұрын
Definitely missing something. Everywhere I read no one has ever used a 1in thick washer. You are 6 lug right? And you have the same calipers I used?
@JoseContreras-mv5yz 2 жыл бұрын
@@sanjuan240 yes im six lug,4x4 hubs,same calipers,and im using nbs spindles to mock everything up
@JoseContreras-mv5yz 2 жыл бұрын
@@sanjuan240 i will figure it out though. If im using all the parts you have i dont see why i shouldnt fit.
@mattbarton2417 2 жыл бұрын
@@JoseContreras-mv5yz Any update? I'm looking at doing the same update. I have a 99 NBS 4x4 and on some videos guys are using caliper brackets to bolt the caliper on, not sure if that's what you were/ are missing.
@JoseContreras-mv5yz 2 жыл бұрын
@@mattbarton2417 i havent bolted it them up yet. Gas prices are up so im not really using the truck as much,but i did mock everything up with no brackets.
@ericmercado 3 жыл бұрын
Any one here have issues with the pedal going all to the floor after the install and bleeding of the brake fluid?
@albertgibbs2937 3 жыл бұрын
You still have air in the system if its going to the floor... Or your master cylinder is bad. Did you have any brake issues before the swap?
@ericmercado 3 жыл бұрын
@@albertgibbs2937 im just get a reply on another video saying the calipers was flipped over I didn’t have the time to check them again also no issues with the stock calipers and discs
@albertgibbs2937 3 жыл бұрын
@@ericmercadoId guess you still have some air Eric. You may need to use a vacuum set up to pull the air out of the caliper thats flipped up side down.
@albertgibbs2937 3 жыл бұрын
Ive literally been waiting 2 months for the driver side caliper to ship from summit racing so didn't have to fight having the bleeder on the bottom of one caliper... It shipped today finally.
@ericmercado 3 жыл бұрын
@@albertgibbs2937 i found this set on Craigslist I paid 180 for all 4 calipers and front dics
@EGGINFOOLS Жыл бұрын
4wd as well or only 2wd for this upgrade?
@sanjuan240 Жыл бұрын
I’ve heard only 2wd but I’m not sure honestly. Couple people In the comments were talking about it. I figure as long as the spindles are the same they should work right?
@nicky20056 Жыл бұрын
Did you use 1500 calipers and what trim package
@sanjuan240 Жыл бұрын
Not sure honestly but there is a difference that’s obvious. They look completely different
@ichiara07 9 ай бұрын
would this setup work on 14-18 models too?
@sanjuan240 8 ай бұрын
That idk
@taylormiller1555 3 жыл бұрын
Do you know if this conversion would work for the 2500 trucks,
@sanjuan240 3 жыл бұрын
I don’t see why not. If I wanted to make sure I would go down to a parts store and ask for a original brake caliper for your truck and see if it’s the same part number for a 1500. If it is then you should be able to do the upgrade.
@taylormiller1555 3 жыл бұрын
@@sanjuan240 the only problem i see is finding the right rotor for the caliper
@sanjuan240 3 жыл бұрын
@@taylormiller1555 let’s say this conversion does work on the 2500. You could just use the same rotor i did part number i showed is from “advance auto parts “. Or do those come 8 lug? Could you just drill the rotor for a 8 lug?
@taylormiller1555 3 жыл бұрын
@@sanjuan240 yeah they are eight lugs. That's what my problem was. I don't feel confident in drilling the rotors without compromising the rotor
@ethans6.0 3 жыл бұрын
did you do it taylor?
@JesusOrtiz-qp1so 2 жыл бұрын
Why don’t you show the whole truck in away that’s dump not showing it
@sanjuan240 2 жыл бұрын
What do you mean?
@jemetricallen8825 2 жыл бұрын
Does anyone know if this will work on a 2017 Silverado
@sanjuan240 2 жыл бұрын
From what i read it should. Just have to make sure it’s shimmed properly
@bigboyhunchoz9384 3 жыл бұрын
Can I Do This On A Sierra 2012 Nnbs 1500
@sanjuan240 3 жыл бұрын
I’m not sure on that. I’ve heard you can since I guess all 99-2020 have similar brake calipers setups . You might have to test fit and see.
@ZackNakazora1 3 жыл бұрын
Pretty cool. I want to do this. do you know if they'll fit under the 2018+ steel wheels. they are 17x8 they came on the base trucks.
@sanjuan240 3 жыл бұрын
Possibly I think the smallest wheel size a stock 2020 runs is 17x8. It would just depend on the offset of your wheels to clear the caliper and I don’t know about that part
@ZackNakazora1 3 жыл бұрын
@@sanjuan240 I have that exact wheel. Check it out on @nomadic.wheelman on ig
@sanjuan240 3 жыл бұрын
@@ZackNakazora1 they look small in pictures but I mean 2020 trucks have 17s I believe. I would test fit your wheel on a friends 2020 and see if it clears fastest way to check I think
@ethans6.0 3 жыл бұрын
bro u gotta chock the wheels
@sanjuan240 3 жыл бұрын
Had the ebrake on. Good looking out though thanks
@ethans6.0 2 жыл бұрын
@@sanjuan240 don’t ever trust ur ebrake with ur life just use some 4x4 or even a 2x4 or a rock anything
@ethans6.0 2 жыл бұрын
@@sanjuan240 do you have ur trans re geared?
@sanjuan240 2 жыл бұрын
@@ethans6.0 I have not
@trentongregor8667 Жыл бұрын
A link for the parts?
@sanjuan240 Жыл бұрын
Everything is eBay for the most part. Oem only for the important parts. Transmission and driveshaft local shops
@luxurnathan4353 3 жыл бұрын
What drop do you have on the Silverado?
@sanjuan240 3 жыл бұрын
4/8
@luxurnathan4353 3 жыл бұрын
@@sanjuan240 what did u use to drop it in the front?
@sanjuan240 3 жыл бұрын
Just springs for now
@zivoxion7094 2 жыл бұрын
What truck is this
@sanjuan240 2 жыл бұрын
2004 Chevrolet Silverado
@bobbyeslick8726 Жыл бұрын
Will this same set up work on 2010 Sierra ??
@sanjuan240 Жыл бұрын
I’m pretty sure it will might just need to shim it differently. I might be wrong but seems like as long as it’s 2wd it should work
@bobbyeslick8726 Жыл бұрын
@@sanjuan240 Man I appreciate that.. can't find alot of info or help on it.. I mean the Wilwood, Brembo etc big brake kits are badass but 2500$ for 2 calipers 2 rotors 2 hoses just high to me. Lol
@bobbyeslick8726 Жыл бұрын
Can't find the caliper anywhere.. do you have a part number
@sanjuan240 Жыл бұрын
@@bobbyeslick8726 go on eBay right now type in “2020 silverado caliper front” should be a pair currently.
@ryanhernandezgaming 3 жыл бұрын
What color name is the truck ?
@sanjuan240 3 жыл бұрын
I’ve been told “topaz gold” it’s some sort of goldish/brown color
@odiarroyo6144 3 жыл бұрын
Naaaa bro..! It's more like, color CACA. LIGHT CACA. Like, Condensado.. Something like it!.
@ryanhernandezgaming 3 жыл бұрын
@@sanjuan240 thanks appreciate it nice color by the way
@sanjuan240 3 жыл бұрын
@brian thanks man!!!
@sanjuan240 3 жыл бұрын
@odi ok
TWA Motorsports
Рет қаралды 15 М.
Crazydayz Fab
Рет қаралды 7 М.
Дима Масленников
Рет қаралды 8 МЛН
TheCombustionGuys
Рет қаралды 22 М.
Lawrence LT Tolman
Рет қаралды 104 М.
Jason Explains Things
Рет қаралды 11 М.
Budget Mechanic
Рет қаралды 622 М.
Дима Масленников
Рет қаралды 8 МЛН