Simple 7 Step Process | How To Detail JET SKIS, WAVERUNNERS & PWC

Simple 7 Step Process | How To Detail JET SKIS, WAVERUNNERS & PWC | Jet Ski Detailing Products

Рет қаралды 17,994

Күн бұрын

In todays video we recored an entire mobile detailing Job that we completed in Redding, Ca! These two WAVERUNNERS were cover in hard water spots! In this video we will teach you how to remove water spots from your jet ski, how to polish your wave runners and how to detail maintain your PWCs. So, Watch this video to take your detailing skills to the next level!
#jetski #shinesupply #detailing
** Timestamps **
00:00 Into Before & After
00:58 Job Intro
03:04 Step 1 Decontamination Clean
03:28 Step 2 Wash
04:19 Step 3 WSP Water Spot Remover
04:46 Step 4 Rinse & Dry
05:46 Step 5 Burn Out Si02 Polish
08:15 Step 6 Clutch Si02 Ceramic Topper
10:13 Step 7 Punch-it | Finish Detail
10:42 Before & After | Outro
👉 Save 15% On ALL Shine Supply Marine Products
with our discount code ( DRAKE15 ) at checkout.
www.shinesupplymarine.com
📸 Follow Drake On Instagram
For Daily Tips and Tricks / drakes.detailing
👉 Book a boat detail with Drake!
Revival Marine Care
💻 www.revivalmarinecare.com
📞 (850) 713-8421
📍 Pensacola, FL . Orange Beach, AL
GET THE KIT!
👉 Jet Ski, WAVERUNNER & PWC Detail Kit: 👈
www.detailusupply.com/product...
Steps:
Step 1 Decontamination Clean
- Smooth Move Paint Decor Spray www.detailusupply.com/product...
- Maxshine Stuff maxshineusa.com/drakesdetailing
Use discount code DRAKE15 to get 15% OFF your maxshine order.
- Pressure Washer amzn.to/3bpxMNY
Step 2 Wash
- Shift Soap www.detailusupply.com/product...
Step 3 WSP Water Spot Remover
- Undrdog WSP www.detailusupply.com/product...
Step 4 Rinse & Dry
Step 5 Burn Out Si02 Polish
- Burn Out www.detailusupply.com/product...
- Microfiber Polishing Pad www.detailusupply.com/product...
- Maxshine DA ( Drake15 Discount Code ) maxshineusa.com/store/p/maxsh...
Step 6 Clutch Si02 Ceramic Topper
- Clutch www.detailusupply.com/product...
Step 7 Punch-it | Finish Detail
- Punch-it www.detailusupply.com/product...
👉 Save 15% On ALL Shine Supply Marine Products
with our discount code ( DRAKE15 ) at checkout.
www.shinesupplymarine.com
👉 Book a boat detail with Drake!
Revival Marine Care
💻 www.revivalmarinecare.com
📞 (850) 713-8421
📍 Pensacola, FL . Orange Beach, AL

Пікірлер: 65

@MikesAutoDetailing 2 жыл бұрын

Fantastic job as always.... Keep up the great work

@DrakesDetailing 2 жыл бұрын

Thanks!

@Justin-hz8bh Жыл бұрын

You're some kind of detailing wizard.

@DrakesDetailing Жыл бұрын

Hahah thanks!

@danconlan8735 2 жыл бұрын

Great job on the Waverunners, they look showroom new! Slainte, DC

@DrakesDetailing 2 жыл бұрын

Awesome!!!! 😎

@Annieswaney 2 жыл бұрын

I wish I got more jet skies. They are nice little guys to do.

@DrakesDetailing 2 жыл бұрын

Heck ya! 😎

Жыл бұрын

awesome stuff You doing .. greetings from Norway

@DrakesDetailing Жыл бұрын

Thanks bro!!

@FinishMastersVB 2 жыл бұрын

Did a Black Yamaha the other day that someone had tried to "Coat" it was horrible. Hope your doing alright out there big dog!! Keep up the great jobs and Intel. Look forward to the class. Holla back..haha

@DrakesDetailing 2 жыл бұрын

Thanks bro! Keep your eyes out! It may be coming soon!

@1lunifyd 2 жыл бұрын

Your videos are amazing you are one heck of a teacher Thank you. The question I have for you is: I own a 2006 205 Sport SeaRay very well taken care of from the previous owner. I want to clean and wax the hull and keep it lookin sharp! I understand the process but I have a concern when it comes to the graphics that are on the hull. The small points are starting to peel off and if I run the buffer I’m afraid that it will pull off or tear the sticker. Do you have some advice for us that have this issue?

@DrakesDetailing 2 жыл бұрын

Just use lighter pressure as you go over the decals and you should be good! 😎

@jbtrailbuilds4763 Жыл бұрын

nice vid you should do a vid detailing a sailboat

@DrakesDetailing Жыл бұрын

If we get a sailboat to do you can count on it!

@noahfisher1424 Жыл бұрын

To remove water spots instantly use distilled white vinegar

@DrakesDetailing Жыл бұрын

Yes that works as well!

@cubaresorts6012 Жыл бұрын

Love your videos been a great help ... love to know what you would charge for ceramic coating for just one of them thanks really dont know how much to charge keep up the excellent work

@DrakesDetailing Жыл бұрын

Hey bro! For ceramic I would probably be at around $150 per foot

@cubaresorts6012 3 ай бұрын

I have another question for you. I see or using burn out Could you use wake up instead? Would it do as good of a job thanks

@chriswichman5259 Жыл бұрын

When using the WSP Spot remover do you have to worry about decals? I seen others tape of stickers.

@DrakesDetailing Жыл бұрын

You can use it on them, just make sure you go easy over them and not too often

@marcusa4846 Жыл бұрын

Quick question… I have a 2022 wave runner and the white plastic on it is turning yellow. What is the best thing I can do to restore them?

@DrakesDetailing Жыл бұрын

Hey bro! Would you be able to send me photo on instagram @drakes.detailing

@hunterbroadnix9609 9 ай бұрын

Great video! Question, what’s a good method for removing water from the foot wells? Normally I use a sponge but it takes forever.

@DrakesDetailing 9 ай бұрын

I fling the water out by hand, as much as humanly possible, then I soaked the rest of it up with a shammy.

@jetclubaustralia 4 ай бұрын

a blower might do I think.

@tim0e Ай бұрын

I use a wet/dry shop vac. Cheap and handy for a lot of things.

@tim0e Ай бұрын

Hey man, I know I'm a bit late to the party but I'm hoping you might be able to recommend something for me to get fuel over flow stain off my ski's black plastic trim. I've tried a few things with little success, if you know if something that would help I'd be really appreciative, cheers.

@DrakesDetailing Ай бұрын

Hey bro, have you tried a little bit of compound on a rag by hand?

@HOMELESSG0D Ай бұрын

Hey Drake I have a client with two jetskis that they left in the water for 2 weeks and are caked heavy with barnacles. What's the best solution to remove them? Thank you

@DrakesDetailing Ай бұрын

For the barnacles on the bottom Muratic acid is going to be your best bet

@josh-pv5cy 3 күн бұрын

So I can take off the seats of my jetskis and water can fall into and it’ll be fine right? Thanks

@DrakesDetailing 3 күн бұрын

Yes just don’t blast them directly

@jetclubaustralia 4 ай бұрын

Hi mate, on step 3 WSP - was the ski dry before you applied the water spot remover? cheers

@DrakesDetailing 4 ай бұрын

Yes, always apply it while it’s dry. otherwise you’d just be dragging it around on a wet surface and waisting the product

@jetclubaustralia 4 ай бұрын

Thanks for sharing it mate appreciate that 👍🏼

@mitjaamersek1917 2 жыл бұрын

When you get to a costumer, do you use their water and electricity? And how do you do it if the costumer doesn't let you use it? Thanks

@DrakesDetailing 2 жыл бұрын

Yes I require the boat to be moved to where there is water and power in keeper for me to do my job

@mitjaamersek1917 2 жыл бұрын

@@DrakesDetailing Thanks a lot drake.

@alaindiaz7535 Жыл бұрын

How many hours did it take you to get these two jet ski’s done?

@DrakesDetailing Жыл бұрын

We took a full day for this one. Wanted to me sure they were 👌🔥

@plaisancejerald1349 2 жыл бұрын

How’s big Dan doing? Used to work with him in the oilfield. Haven’t talked with him in awhile

@DrakesDetailing 2 жыл бұрын

He's doing good! he just got re married to a great lady!

@plaisancejerald1349 2 жыл бұрын

Good for him! Preciate the videos! Taught me alot on bringing back my boat to life and keeping it up! Thank you!

@Jcolli2209 Ай бұрын

Want to buy the kit but the website link doesn’t work for detailussupply

@DrakesDetailing Ай бұрын

Hey bro! That site is no longer in service. Here’s the new link: shinesupply.com/collections/marine-products Use my discount code DRAKE15 to receive 15% off of your purchase, but it only works with the link that I dropped in this comment. 😎 Thanks!!

@MikesAutoDetailing 2 жыл бұрын

1st

@DrakesDetailing 2 жыл бұрын

😎

@madomad5864 Жыл бұрын

Watching this at 3am and I don't even own a jet ski

@DrakesDetailing Жыл бұрын

Nice! Haha

@Annieswaney 2 жыл бұрын

How is the wsp on metal?

@DrakesDetailing 2 жыл бұрын

Works good, but you have to wash it off immediately, or it will corrode it

@Annieswaney 2 жыл бұрын

@@DrakesDetailing mine is the same. Thank you

@Annieswaney 2 жыл бұрын

Question on the wsp again. I got a new customer with a new Cobalt that is covered in water spots. The bumper rail is covered too. Just rinse, huh? I’m Worried about the metal on the bumper rail. Is this acid going to do Any Harm(I mean any) Also For a new boat after the wsp, what would you do next? Does it need to be polished, and then what? I really want to keep this customer, very good money with this boat.