No video
SKR Pro v1.2 - TMC2209 UART with Sensorless Homing
Рет қаралды 9,394
Күн бұрынThis is a basic tutorial on how to configure the TMC2209 with sensorless homing on the SKR Pro v1.2 board.
SKR Pro v1.2 Playlist:
• SKR Pro v1.2 Tutorials
One Time Tips, You Can PayPal Me:
www.paypal.me/...
Patreon:
/ edbraiman
Discord Chat:
/ discord
Hardware:
1 - BigTreeTech SKR Pro v1.2
1 - USB Serial cable
1 - PSU 12 volts
3 - BigTreeTech TMC2209 UART
4 - NEMA17 Steppers
Amazon Affiliate Links:
(SKR Pro v1.2)
(TMC2209 UART)
(Micro SD Card Plus Adapter)
Software:
Marlin Firmware 2.0.x
marlinfw.org/me...
VScode install:
• Installing VSCode with...
Pronterface:
www.pronterfac...
@mattlogue1300 2 жыл бұрын
Thanks I learned a lot. Now I need to remember it. I never knew microsteps had to change. Guess it can be a function.
@MarFox001 2 жыл бұрын
Thank you so much for this clear tutorial! Helped me a lot!
@EdwardBraiman 2 жыл бұрын
You're welcome.
@mastreautomacaoindustrial2750 3 жыл бұрын
Hi Ed. Thank you for taking care of the quality of what you do! Beforehand, I apologize because I don't write in English, I'm using a translator. I have a MTB set, SKR Pro v1.2, TFT 35 and TMC2209 board. I need to use sensorless to homing, but also to level the table and write this data to the EEPROM. If possible, make a video about it. Thanks.
@EdwardBraiman 3 жыл бұрын
I'm hoping to make dozens of videos soon, we're getting hit with a heatwave, so standing in high temps and humidity limits my recording time.
@mastreautomacaoindustrial2750 3 жыл бұрын
@@EdwardBraiman Existe maneira de utilizar o sensorless UART do TMC2209 para fazer autonivelamento da mesa?
@yhhsieh Жыл бұрын
The temperature of the z-axis motor is very high, why?
@EdwardBraiman Жыл бұрын
Which motor are you using for NEMA?
@design8studio 2 жыл бұрын
Quick question. I'm following along to RE-configure my setup for sensorless homing. I had previously installed the TMC 2209 drivers without sensorless homing. Back at that time I was instructed to "bend" down a pin on the underside, which as per when you insert the driver at 3:40, the bent pin would be 3rd pin from the left at the top of video window. I cannot now remember why I bent it, but I am seeing that you did not bend a pin. I'm guessing I need to "un-bend" it, but I want to make sure. Do I indeed unbend it?
@EdwardBraiman 2 жыл бұрын
You have three options replace stepper, bend pin back or solder a new pin in place.
@design8studio 2 жыл бұрын
@@EdwardBraiman OK, thank you!
@EdwardBraiman 2 жыл бұрын
You're welcome.
@design8studio 2 жыл бұрын
@@EdwardBraiman SUCCESS! After a lot of tweaking config files and compiling firmware, I finally got Sensorless Dual Homing working for both Y and Z on my LowRider v2 full-sheet CNC with SKR Pro 1.2 and TMC2209 drivers!
@EdwardBraiman 2 жыл бұрын
Congratulations 👏
@roi9875 3 жыл бұрын
If I want to flash the board directly from the usb, do I still need an sd card? If I do then do I have to keep it in forever, or can I remove it and use it to upload gcode. Thanks
@EdwardBraiman 3 жыл бұрын
In order to load firmware you will need to remove drive and load firmware.bin. you can remove after flashing firmware.
@spiauto 3 жыл бұрын
How difference between SKR PRO 1.2 and SKR 1.4 turbo?
@EdwardBraiman 3 жыл бұрын
Different processors and more solid board layout.
@evo-3d114 3 жыл бұрын
Un petit coucou de la France où je suis déjà depuis pas mal d année tes vidéos. Est ce que un jour on aurait une vidéo en Dual x Carriage pour faire un Idex sur marlin 2.0
@EdwardBraiman 3 жыл бұрын
avec COVID-19, beaucoup de mes temps ont été redirigés ces 18 derniers mois.
@evo-3d114 3 жыл бұрын
Oui mais vous faites beaucoup de vidéo et des Foix un peu la même chose. Je pense que beaucoup aimerai une petite vidéo Idex, avec votre super qualité d explications
@cricri3d 3 жыл бұрын
Good job, skr 1.2 vs 1.4 turbo which is the best?
@EdwardBraiman 3 жыл бұрын
Depends on your individual printer needs.
@mattlogue1300 2 жыл бұрын
I'd say the pro if you are advanced user
Andreas Spiess
Рет қаралды 547 М.