Smooth arc VEVOR MIG 270 - 3 in 1 WELDER - MIG, TIG, and STICK! TIG torch included!

Рет қаралды 11,910

Күн бұрын

WOW! I'm impressed! Super smooth and stable arc in all 3 processes!
DISCOUNT CODE!!
VVMH5%OFF (5% off on all products)
Affiliate link: (This welder)
s.vevor.com/bfQscD
Chapters:
00:00 Who I am
01:13 FLUX CORE
01:51 TIG
04:19 STICK
05:59 MIG
07:45 SUMMARY

Пікірлер: 33

@geh3254 10 күн бұрын

Purchased this welder about 8 months ago, haven't used it yet due to moving and also need to re-set up my work shop. Very encouraging review, thank you. You look like Kevin Costner.

@neilyakuza6595 3 ай бұрын

Great review, I am purchasing one.

@user-qz6iv3ox4u 5 ай бұрын

Keep on trucking good mig

@diggindiggenit6540 10 ай бұрын

I have yet tried an igt machine still using other older machines, it's tempting for sure but I am usually welding over quarter inch most of the time

@user-qz6iv3ox4u 5 ай бұрын

Mig is very nice

@douglasfox9579 4 ай бұрын

What kind of penetration were you getting? I am okay with terrible form - its the strength that counts! Thanks for the review.

@jamesbarisitz4794 3 ай бұрын

Thanks for the review. Seems like a bargain.

@John-vf9py 4 ай бұрын

With your code and they have if for 13% off also, this is literally $258 delivered! A complete no-brainer for a home owner machine for sure.

@joehenry447 16 күн бұрын

HI , how did you tig weld without the argon gas hooked up as you did not hook up the gas until you went to mig weld .

@SANDS78 8 ай бұрын

Does it have hot start for stick?

@richweir5186 5 ай бұрын

I'm looking to buy this because I haven't got a reasonable way to run 220 into my little shop. I was hopeful that you would show it operate on 110.

@WideVisionMetalFab 4 ай бұрын

Sorry about that. I cut that section out because of how long the video got. It will weld 1/8 inch on 110v for a decent amount of time before needing a rest. It will probably weld 14 gauge all day. I did weld 3/16 for about 4 inches before it tripped the breaker.

@victorreppeto7050 8 ай бұрын

For shortcoming of cheap mig welders seems to be welding thin sheet metal and or spray transfer with steel and aluminum. Could you do a follow-up video and cover these items?

@WideVisionMetalFab 8 ай бұрын

I've welded 14 and 16 ga sheet with it, and it does really well with them. I do want to weld aluminium with it, and I'll will post a video of that adventure. :)

@willwatlington6750 3 ай бұрын

Are the settings for wire feed speed in imperial or are they in metric?

@Rigoknow 7 ай бұрын

👍

@Theroadgypsy 3 ай бұрын

Can it take an aluminum gun?

@WOODZMAN 8 ай бұрын

What about on 110V, Have you tried it ?

@WideVisionMetalFab 8 ай бұрын

Yep. Due to time, I cut it out of the video. I was able to weld about 5 inches of 1/8 inch thick metal together with an inside corner weld no problem. I tried 1/4 inch, but it tripped the breaker after about 30 seconds. I'm not sure what the max amp and duty cycle is on 110 volt.