No video
SNES is only showing a black screen, can i fix it?
Рет қаралды 1,976
Күн бұрынMy SNES stopped working, can i fix the problem?
In case anyone is wondering why i was having so many issue at 2:10... my soldering iron had shut off on me and i didn't realize for a bit.
Thanks for watching!
Buy Goodies from Japan!
sendico.com/re...
@Retro_Cave 6 ай бұрын
Guys... i'm at a loss. :cries: I'm open to suggestions.
@tommyfobe84 5 ай бұрын
Could be a processor problem. they make snes cartridges that are made to troubleshoot specific codes that you can look up. Please post an update video🙏🏻
@Retro_Cave 5 ай бұрын
@@tommyfobe84 i can't even get it to boot my everdrive to run the troubleshoot cart. I've re-capped, and tried a new D1 diode. So far no dice :(
@Retro_Cave 2 ай бұрын
I MIGHT have figured out the issue. I was poking around looking for shorts when i found a shorted capacitor... which in turn led me to a shorted inductor L1. I ordered new parts and will do an update when i get them.
@anthonyterry8162 13 күн бұрын
Did you check voltage reading after replacing the 7805? If you see a voltage drop, it could be a blown component somewhere
@R3TR0--93 3 ай бұрын
I had a similar issue it turns out that the cartridge slot needs to be cleaned of corrosion of any dirt, dust, same for the cartridges. If your model is the one where you can remove the cartridge pin connector and clean or replace it. I would also recommend replacing the pico fuse, sometimes it can be low voltage from the actual power supply that plugs into the wall. And it could very well be the on board PPU or CPU chips even RAM which you could replace.
@frugalprepper 3 ай бұрын
Usually I spray so deoxit in the connector when this happens. You may also want to try a cap replacement.
@Retro_Cave 3 ай бұрын
I did a full re-cap. Still dead :( I will re-visit the connector and see if i can get anything.
@rubenmejia4881 5 ай бұрын
Did you try giving all the pins a good cleaning? Maybe its not making proper contact trying giving the carts a wiggle while testing for power
@Retro_Cave 5 ай бұрын
Scrub scrub, ya, i've cleaned it quite well.
@elisac6146 2 ай бұрын
Have you double check the pins?
@Retro_Cave 2 ай бұрын
I'm running out of things to double check. I get a blank video when i turn it on, tv sees the snes sending out a signal, but i get nothing :/
@EvilCoopra 3 ай бұрын
I would strongly advise against fixing Super Nintendos with lead-free solder.
@TylerSteiner 3 ай бұрын
Oh, i never use lead free solder. Leaded all the way.
@Retro_Cave 3 ай бұрын
Lead free is hard to work with, and doesn't have the flex or give like leaded solder. I use leaded unless i absolutely cannot for some reason.
@EvilCoopra 3 ай бұрын
@@Retro_Cave Yep, I absolutely agree with you. In addition, the risk of destroying various components and/or the circuit board is quite high, as the processing temperature for lead-free solder is significantly higher. The longevity of the solder joints is also highly questionable.
@jimdavis6833 4 ай бұрын
Your piano is driving me nuts.
@TylerSteiner 4 ай бұрын
Lol, what? What Piano?
@sammydavis3796 5 ай бұрын
lol I actually have the sound track to Chrono Trigger in my playlist
@RonAlam 4 ай бұрын
Bad PPU or possibly bad ram/bad trace
@danielsantana540 6 ай бұрын
How do these snes systems.get bad i never had a hardware problem with my snes😊
@DimitrisDr3am 5 ай бұрын
You never had a 30 year old SNES I'm guessing
@danielsantana540 5 ай бұрын
@@DimitrisDr3am ur right hadnt though some youtubers had told me they had Nes snes for over 30 years and still works
@Retro_Cave 5 ай бұрын
Both my SNES's were working until i started messing with mine, and i did something to it. It didn't just stop working on its own. I'm STILL trying to figure out what i did to it.
@danielsantana540 5 ай бұрын
@@Retro_Cave i see. In the 90 s i only had sega genesis not Super nes. I didnt pick up snes until 2018 i got it for 77 bucks at a gamestore in town
@rubenmejia4881 5 ай бұрын
That would be the key step in the repair is to understand what you did when you first started tinkering. Sometimes, accidental tinkering can result in a loss. What was the cause that got you to crack it open? My guess when the fuse blew its a possibility it also knocked some of the ppu or cpu ic's out. Usually a blow fuse is a easy fix but if more current went in after the fuse blew by tinkering that could have caused the damage. @Retro_Cave
Wil's VG Addiction
Рет қаралды 1 М.