So You Blew Your Motor, Now What?
Рет қаралды 37,814
Күн бұрынOver the past year I have talked to everyone about how to increase the reliability of your engine. But what happens if you blow up your motor? Well lets talk about it! It really boils down to a few options:
1) Rebuild the Stock Block
2) Buy a new OEM Block
3) Buy an After market Block
4) JDM Engine swap the car
There are definitely some things that you need to keep in mind when it comes down to what option you are going to go with. Each has their benefits but their drawbacks as well.
1) Rebuilding your stock block might be the most cost effective solution but it is really going to come down to what all is wrong with the motor. Sometimes it is not salvageable and in circumstances like that you might need to consider other options.
2) Buying an OEM Block does have its benefits as it may be covered under warranty by Subaru.
3) Aftermarket options are a very good idea for those looking to make good power. IAG, Rev Works and Crawford are some very good options to consider.
4) While JDM Engines might be cost effective, they are not the easiest to work with when it comes to modification.
Smeedia Memberships: bit.ly/3bNQv0C
Smeedia Merch: www.smeedia.net/shop
Send Me Stuff (P.O Box Address)
Tanner Smith
Smeedia
1002 N Meridian Ste 100 PMB 120
Puyallup, WA 98371
Parts Used:
IAG Performance: bit.ly/2TcMACF
Rev Works: bit.ly/347GZE2
Crawford: bit.ly/359YmUa
Outfront Motorsports:bit.ly/3dBUwH8
Suggested Tools:
Beginner Tool Kit: amzn.to/3jcRFqn
Starter Electric Tools: amzn.to/2OttJRC
Cheap Pliar Set: amzn.to/3eCliOC
The Best Light for waorking on your car: amzn.to/30lQ89b
Fancy Racheting Wrench Set:amzn.to/32sQixY
The Best Metric Socket Set: amzn.to/2ZzgaX0
You need Jack Stands, Duh: amzn.to/3h7oB1T
But you also need a jack...: amzn.to/30faaCc
Hook and Pick Set to grab all the small things: amzn.to/2Oui58X
Tape measure to get them lengths: amzn.to/2CD432i
Measure all the Small Things: amzn.to/3fCj7vM
The Only Screw Drivers you need: amzn.to/3jaYid6
Fancy Electric Impact: amzn.to/30gqUc9
Battery for your Impact Boi: amzn.to/3j94kuH
Trust me you need Pry Bars: amzn.to/2WtIUyu
Music:
Boost by Joakim Karud / joakimkarud
Music promoted by Audio Library • Boost - Joakim Karud (...
Deux by dyalla / dyallas
Music promoted by Audio Library • Deux - dyalla (No Copy...
@Hyunw22 3 жыл бұрын
My motor blew. What I did is cry
@Smeedia 3 жыл бұрын
Hopefully it wasn't for too long 😪
@joegrant2828 Жыл бұрын
Mine too
@kyles4744 6 ай бұрын
That is fair ! I'd cry to
@jonathandyang 4 ай бұрын
Mine blew today. 32K miles. I drove it for 8K, immaculately maintained and driven like a human, not a maniac. Fuck
@baelm 3 ай бұрын
just blew mine after an oil change lmao@@jonathandyang
@TurbhoeHDRemix 3 жыл бұрын
Everyone's talking about power goals, and I'm in my 2004 WRX and I'm satisfied with 300-320 hp. I'm not trying to be the fastest on the streets, as is I can keep up with A LOT of things. I just wanna be able to keep doing what I'm doing.
@evsep79 3 жыл бұрын
Your the man! My 2004 sti came back with 40 psi low on a cylinder... this is exactly the information I needed, I am thinking of going with IAG stage 2! Thank you !!!!
@Smeedia 3 жыл бұрын
Sorry to hear but the IAG set up should be a great set up!
@ieatcolors7446 3 жыл бұрын
love it. thanks for the tips and ideas man. getting a engine soon. cars coming back!!
@Smeedia 3 жыл бұрын
Yesss!!!! What are you looking into?!
@paulmarsdensr1095 3 жыл бұрын
A really good video. JDM. I keep seeing that term. Stay safe brother.
@jayman4874 3 жыл бұрын
Recently spun a bearing in my stock FRS.. Think I’m gonna go with a IAG stage 1 short block that way when it is time for forced induction down the road, the engine will be stronger. This video helped a lot !!
@joegrant2828 Жыл бұрын
Gonma prob cost atleast 11k if you have someone do ot for you
@joshuathomas4934 11 ай бұрын
@@joegrant2828in what world? My Subaru shop near me charges 2659 for labor to replace a shortblock. Shortblock is about 2000 dollars. Plus at least 1000 in parts and labor for the heads. How are you looking at 11k dollars?
@joegrant2828 11 ай бұрын
@@joshuathomas4934 i spun rod bearing. Shot metal all through block and turbo. I called tuner shops they wanted 11 grand to replace. Subaru tech ended up charging me 9k with new turbo. Where do you live. And are they giving you rebuilt block. Or brand new
@joegrant2828 11 ай бұрын
@@joshuathomas4934 curious to hear where you are getting such cheap labor from. Subaru wrx stis arent cheap to maintain and also expensive to add alot of power to. The engine from my year had lots of these problems. Subaru got tired of paying even though there fault.
@Fix_it_Garage 3 жыл бұрын
This video is great! Im glad I picked up the IAG stage 2.5 tuff block. When I called IAG they were super helpful with finding my the right block and other parts based on the power and what i wanted to use it for.
@Smeedia 3 жыл бұрын
IAG has incredible customer service 🔥 congrats on the new motor!
@santostuner 3 жыл бұрын
So you got it done right away how much was it for all the labor and everything? I want to get it done 2.5 to mine as soon as possible
@j3jymann 8 ай бұрын
How has it held up? Do you still have it and what kinda miles?
@Fix_it_Garage 8 ай бұрын
@j3jymann so far it has held up very well. I've only done about 6k miles but most of that is on the track or autocrossing. It gets all the fluids changed multiple times a season and the motor is holding up very very nicely
@marlonperuse830 3 жыл бұрын
Yoooo he's back again
@Smeedia 3 жыл бұрын
Eyyyyyy 🙏🔥
@christianm2303 3 жыл бұрын
Please don’t talk about this, ur giving me anxiety
@Smeedia 3 жыл бұрын
Lol this is only in the extreme case, the question is always asked so figured it wouldn't hurt to cover it 😅🙏
@killrockstartv 3 жыл бұрын
don't see it as a bad thing, it's a right of passage!
@lowlifeangler 3 жыл бұрын
Honda owner?
@thomasvue6136 3 жыл бұрын
Such a perfect timing. I've been thinking about buying an ej207 v7 or rebuild my ej205, maybe boreing out the walls making it a 2.1L with a twinscroll setup. Both are gonna be difficult so I'm stuck
@Smeedia 3 жыл бұрын
Both are solid options just boils down to budget and what you want 🔥🙏
@SaW216216 3 жыл бұрын
Tons of information! Noted everything down
@Smeedia 3 жыл бұрын
😁🔥😁🔥😁🔥
@christopherbroadhacker6663 3 жыл бұрын
Hit the nail on the head for motors. I love it. IAG is great, but STi Type RA motor sounds even more interesting and cost effective
@Smeedia 3 жыл бұрын
Much more cost effective and had been pretty proven so far 🔥🙏
@christopherbroadhacker6663 3 жыл бұрын
@@Smeedia I have always been curious of how much can be pushed. You are awesome thank you
@C4PTAINinsano 3 жыл бұрын
Would the type RA block work with ej255 heads? It would raise the compression.
@Smeedia 3 жыл бұрын
It would work and compression would be slightly diffrent
@SubieDougz 2 жыл бұрын
Best channel on KZfaq
@Smeedia 2 жыл бұрын
❤❤❤
@crazyboi1818 3 жыл бұрын
Just a tip if you blow a Subie motor you can go right to any subie dealership and order another block for around 2k (for BRZ)
@ajw828 3 жыл бұрын
Well said. Definitely a terrible feeling the first time the motor goes. I hear it gets easier? Hoping to not find out haha
@Smeedia 3 жыл бұрын
The legends say that it gets easier but only the chosen few truly know...
@sam_ausz3281 3 жыл бұрын
On my second spun bearing... Promise you, it does not get easier. 🙃
@dorianpalmer4871 3 жыл бұрын
Great video btw
@Smeedia 3 жыл бұрын
Thanks my man 🙏😁
@maxzumtobel3819 3 жыл бұрын
hey man, what rain gaurds do you have. I also love your channel and now I wanna wrap my subie bc of your vids.!
@Smeedia 3 жыл бұрын
They're the OEM Subaru rain guards 🙏😁
@davidpedraza1433 Жыл бұрын
Perfect video I just blew my fa20. I’d like to go the RA route. Just trying to find a shop that will build this for me. Some shops in Texas will only put iag in.
@PatFan1980 3 жыл бұрын
Nice vid 🤙🏼 I spun a rod bearing in my car. Went with a built block by Crawford. Might never utilize its full potential but it was extremely important to me to have forged pistons.
@Smeedia 3 жыл бұрын
Totally agree and you can't go wrong with crawford!
@TheJasbmx 3 жыл бұрын
About how much did u pay for that with installation?
@PatFan1980 3 жыл бұрын
@@TheJasbmx I just paid the cost of the short block (Crawford S2). I’m rebuilding and installing everything else
@TrickyHaze. Жыл бұрын
Forged internals on stock block?
@somdetkhamda6691 3 жыл бұрын
OMG, this video is perfect for me since my car just blew up on the DYNO today. I was doing a stage 2 plus tune on my 2016 STI and the motor seized up, so I am assuming it was a rod/bearing. I cried inside when it happened earlier today, so I'm trying to push through it. Maybe an IAG stage 1 or stage 2 short block? Might just machine the heads and get them all cleaned up. Thinking of an FP turbo of some sort? Thanks man--love your vids, Bro!
@Smeedia 3 жыл бұрын
Sorry to hear 😢 the Type RA block is a good cost effective option but how much power so you want?
@somdetkhamda6691 3 жыл бұрын
@@Smeedia I'd be happy with 400-450 whp. Yeah it was a very sad moment. My Subaru guru buddies recommend maybe a stage 1 IAG block? I'd be happy with that. I would upgrade turbo, oil pump etc.. since I don't know for sure where all the little metal critters from rod bearing migrated too.
@Smeedia 3 жыл бұрын
Type RA short block is cheaper and have been proving themselves around the 550WHP mark
@joez.9932 3 жыл бұрын
Bro, ALWAYS GO DEEP !!!😂😂😂😂
@Smeedia 3 жыл бұрын
More to come lol wanting to go deeper into each option but would have been wayyy to much info for one video 😅🙏
@benjaminstuart8626 2 жыл бұрын
Just got rod knock on my RA block lol good thing I kept it stock.
@Craiggg12345 2 жыл бұрын
I got rod knock my my 2015 STI at 105k lol. The bearing rod knock on the RA is a hit or miss.
@user-nf3oq2ge3g 2 ай бұрын
Keep the trumpet solute song handy in your car then when it blows, you can solute it while blasting that song on the side of the road till your trailer comes.
@WithCarePlz 2 жыл бұрын
So I haven’t blown up the ‘18 STI yet, but I’m already going down the rabbit hole of building a motor. I want an overbuilt reliable 600hp on 93. With as FLAT a torque curve as possible. What sort of setup would you recommend? Long block or short block? I was thinking of getting an IAG 900 setup and running only 600hp with it so it’s overbuilt af. Long block, short block, closed deck, open deck? There’s just so many options out there lol. I just want to keep the track handling sort of setup but have 600hp on tap if i want it. But what sort of motor build/turbo setup would your recommend based on the stuff I stated? Stuff will always break, but I want a beefy setup cuz nobody wants to be *that guy*. You know that guy. The one who blows up his subaru 4x and keeps doing things half assed
@andyrasmussen2222 2 жыл бұрын
blew the engine in my '12 sti hatch today, have had this video saved for a long time lol.
@Smeedia 2 жыл бұрын
NOOOOOOO 😭😭😭 what's the game plan?
@andyrasmussen2222 2 жыл бұрын
@@Smeedia not sure atm, gotta see how much (if any) of the SB is salvageable. If not then I guess we're going type RA!
@willeyvelazquez4868 3 жыл бұрын
Go in deeper in to the different motor and what to expect
@Smeedia 3 жыл бұрын
Coming in some more videos going to break then down 🙏
@bennyang8049 3 жыл бұрын
Thanks for the information on the various engine options. With cars nowadays have so many sensors and computers, if i go with an aftermarket block, does it mean i have to replace all the existing wiring and ecu so that I don’t get some gremlin electrical and fault codes?
@Smeedia 3 жыл бұрын
No sir, you can use the factory sensors and harnesses 😁
@nathanvorheswrx1770 3 жыл бұрын
Yeshkamesh! My name a Borat! What can you do if blow motor?! Very nice!
@Smeedia 3 жыл бұрын
This explains what I've been seeing Borat pictures lately 👀
@xlosksor7801 Жыл бұрын
I ended up spending a lot more than I expected 😂 but Ik it’ll help me on the long run runing a stage 2 iag with support mods
@dean_cain Жыл бұрын
Can you do an update on this with non Wrx Sti motors?
@boostconcept_ 3 жыл бұрын
I didn’t blow my motor but I’m waiting on a EJ207 short block and refurbishing my EJ20G heads on it, should handle over 300hp
@thumpertorque_ 5 ай бұрын
What are the difference between EJ257 and EJ207? The JDM is a smaller engine so does it still have potential for more power than the US one? Is the RA even better than the JDM?
@jordyluna1797 2 жыл бұрын
Is this including the short block rebuild or just a short block swap
@thumpertorque_ 5 ай бұрын
What year STI comes with the type RA short block? Or does it come with the type RA only?
@milesd3928 3 жыл бұрын
Luckily they put the ra block in the 19+ sti as well, I am hoping they prove to be able to make 500 up reliably..... but for mine I am thinking 400 whp just to keep it hopefully more to the safe side
@Smeedia 3 жыл бұрын
400 would be a safe side for it and oodles of fun too 🔥
@theshadowowl4196 3 жыл бұрын
Idk if you have any plans on uploading about this but how’s the Neon SRT4? Anything interesting happening with that process? I haven’t heard about it in a while
@Smeedia 3 жыл бұрын
Nothing yet, we need to put it on stands and pull all suspension and brakes off the car. Been bugging Matt to get it going 😅🙏
@dannythompson1948 Жыл бұрын
Ooohhh I've come so far since my last comment on this video.. Today's the day I get my type RA Shortblock!! I already got a new vf48, and I plan on having the heads decked and valves done. I''m hoping that I'll have the closest thing to a new 2012 STI as possible..
@Smeedia Жыл бұрын
Ohhhhh the RA block was a good move 🔥🔥🔥
@cjhouse8666 3 жыл бұрын
My motor blew previous owner beat the hell out of it and traded in and I bought it. Cylinder 4 went thankfully I caught it right when it happened. Went IAG Stage 2 block and couldn’t be happier.
@Smeedia 3 жыл бұрын
Shooting for more power as well? Sorry to hear, see that happen too often 😭
@cjhouse8666 3 жыл бұрын
@@Smeedia Nothing too crazy just want to max the stock turbo out now. I’m trying to skate the line of power and reliability lol.
@Tony-tk4ht 5 ай бұрын
hey smeedia from your experience what shortblick do you recommend? my ej255 spun a bearing and trying to get it back and going
@dankcincy 2 жыл бұрын
You don't have to use a JDM ecu with a JDM swap. You swap a cam pulley and the crank pulley. That's all you have to do. Easy peasy. You will need a tune and you CAN use an Access Port. You don't need to go open source.
@westtexas501 Жыл бұрын
so will the 2018 sti RA short block swap into my 2013 wrx 2.5T without any modifications?
@kazerzero5360 2 жыл бұрын
I just spun a bearing on my 08 sti. Looking at the type ra sb and the only difference is the piston design. Comparing that with the iag stage one, I feel more at ease with the stage one because everything is forged and they use better bearings. I do have full bolt ons with an fp green. Was hoping at making around 450 whp with my current setup. Which would you recommend going?
@Smeedia 2 жыл бұрын
I'd suggest the type RA, they're reliable blocks for a fantastic price. You can snag RA blocks for under $2,000 if your not looking to make more than 450whp I'd always suggest an RA. My old 05 STI had an RA block making 460WHP and I beat thr hell out of it. Never had an issue and the block still runs fantastic
@VenomHadesOfficial 2 ай бұрын
Is the Type Ra shortblock better than the STI 2004 EJ207 Shortblock?
@07BLUESTI 6 ай бұрын
Interesting, two shops said they refuse to even sell me a type ra cause they keep blowing up including an S209 that’s currently there tf?
@lowlifeangler 3 жыл бұрын
My engine timing chain tensioners broke , Fn up the valves and rocker arms. Swapped it out with a newer engine...of course ...it was a 2.2 Ecotec by GM LoL
@Smeedia 3 жыл бұрын
Oof, I've only seen a handful of chain engines snap but when they snap..... its usually pretty catastrophic 😖
@cay378 3 жыл бұрын
Why was I looking this up last night and now this comes about! Catastrophic engine failure in my 15’ STI, was trying to find out if it’s cost effective to go OEM (More expensive) or just go IAG 2 Tuff. Tough decisions 🤣
@Smeedia 3 жыл бұрын
Its a sign! All going to boil down to how much power you want to make, TBH the type RA short block is a pretty good route to go for the $$$
@cay378 3 жыл бұрын
@@Smeedia yea when I was looking last 15+ STI longblocks are in the high 8-9k range, meanwhile a 2 Tuff is 3600. Didn’t think about RA stuff, now just to find out if my heads are good 🤣
@Smeedia 3 жыл бұрын
Depending on what the failure was they should be, most of the time the heads can be cleaned up at the machine shop 🙏🔥
@cay378 3 жыл бұрын
@@Smeedia Cyl 2 windowed top of the block, can see Cylinder wall ravaged so hoping it didn’t make it up to the head but who knows, we shall see once winter goes away 🤙🏼
@Smeedia 3 жыл бұрын
Oh God 😳
@TDLmc 3 жыл бұрын
Blew my FA20DIT, happens that putting forged internals is cheaper than going the OEM route. So I guess I will have some potential for more ponies down the road :D
@Smeedia 3 жыл бұрын
Yesss, always an opportunity to look at it as more power 🔥😁
@andrescano1122 3 жыл бұрын
How did you blow it?
@TDLmc 3 жыл бұрын
@@andrescano1122 too hard driving I guess, maybe a bad tuner too
@CaptainMeliodas 3 жыл бұрын
@@TDLmc Are you building it yourself?
@TDLmc 3 жыл бұрын
@@CaptainMeliodas No, it actually requires honing since the sleeves got scratched! Putting 86.5 pistons on it
@Grooove_e 3 жыл бұрын
I daily an 03 wrx that still has the original engine, transmission and even the original turbo at 150k miles im really living life on the edge
@Smeedia 3 жыл бұрын
Nahhh, your solid up to like 500K 😉🔥
@Grooove_e 3 жыл бұрын
@@Smeedia It is completely unmodified besides a cat back exhaust so I'm hoping it'll make it to at least 200k! Like you saw though I'm gunna have new motor and trans on the ready for when it goes lol
@erics6088 3 жыл бұрын
Been looking around for a cost effective option, since my ej255 looks like it might be on its way out (ringlands, probably 😑). Never considered an oem SB before, but I like the price. Would the Type RA SB be compatible with the D25 WRX heads? Really looking for a reliable-ish 350-400 wheel daily driver (after other mods, obviously).
@Smeedia 3 жыл бұрын
Not sure if the D25s are direct swap i know the W25s are. Someone has to have done it before. 🙏 the RA block would be a good option 🔥🙏
@erics6088 3 жыл бұрын
@@Smeedia Cool, I'm gonna look more into it. Thanks for the info, as always, and I appreciate that you actually read and reply to comments. Shows you care 🤙
@Smeedia 3 жыл бұрын
I try 🙏😁
@stanleymonroy1891 Жыл бұрын
My Subaru has a rod knock so I bought a new type RA block do I need to take the heads to get resurfaced ? Even tho the car didn’t heat up? Because you take the heads when your car get over heat on my case it didn’t I moneyshift I need help lmao
@JarredCHILL 3 жыл бұрын
it’s crazy because i blew my motor not too long ago and i’m getting it rebuilt as we speak
@Smeedia 3 жыл бұрын
Hopefully rebuild time does not take too long 🙏🔥
@cassiejvance7496 3 жыл бұрын
Hi Tanna. This thing is going to be a total beast. Did you update your life insurance just as a precaution lol. Waiting for this motor got me feeling like I'm 10 and wanting for santa to 🎅🎅🎅. Need some wheel & tyres advice for my 09wrx. I really like the look of the R888 tyres?? 🤘🤘🤘🤘
@Smeedia 3 жыл бұрын
Lol sammmmme, been waiting for it to come back! And the R888 are great tires, keep in mind there are not too many evacuation channels for water on them so on wet days they might be pretty slick when driving 🙏
@cassiejvance7496 3 жыл бұрын
@@Smeedia so definitely new for the summer tyres. 🌞. Are you going to be swapping the exhaust system for the new motor??. Forgot to say I finally got a guy to custom build the pipes for my rear box and it sounds like a RB22 sti. Had a long wait finding the right person to do the work, but well worth it. I'll get some pictures and IG you 👌🤘
@Smeedia 3 жыл бұрын
Glad you got it sorted out! I'll be using the ETS exhaust from my old set up and having the fabricator make a downpipe to mate up to it 😁🔥
@cassiejvance7496 3 жыл бұрын
@@Smeedia it's going to sound Sweeeeet lol. Take care Bro 🤘🤘🤘
@fredastaire6156 7 ай бұрын
I didn't blow my motor but I'm watching this for ideas to project build a built engine as project; slowly 😉
@lukeb4657 3 жыл бұрын
Been a long time watcher and never thought I would have to re visit this video my 16 wrx is knocking and its confirmed rod knock. Not sure what my next steps will be, f Ill go built or not. From your experience what would you suggest? It was just a fun daily I have 5k saved up for emergency car stuff so Im willing to spend all that plus some to get it done right. My goal before engine blew was to do flex fuel kit next and that's it but now I might have to go full beans lol. I just need pointed in a direction this is a new area for me I haven't done research on engine components before. mods egr and tgv deletes catted downpipe bypass valve cold air intake ecbs
@Smeedia 3 жыл бұрын
Do you have an end goal for power or do you just want it back on the road?
@lukeb4657 3 жыл бұрын
@@Smeedia i want to make low 400s
@lukeb4657 3 жыл бұрын
Just reliable fun in the low 400s is what i want to do some guys in my car club recommend Sri swapping it for cheaper but I’ve gotten a lot of recommendations and you seem to put reliability high up on your list then most which is one of the reasons i like watching your videos so much.
@Smeedia 3 жыл бұрын
If just low 400s, built internals rods and pistons, a little head work and the motor should hold just fine. Swapping an EJ into an FA car is doable but not worth the work IMO
@lukeb4657 3 жыл бұрын
@@Smeedia Thank you for responding to me so quick I haven't even got response from the shops yet. Thank you Tanner Hope you had a Merry Christmas!
@ghandi716er9 3 жыл бұрын
What about a video explaining hybrid motors
@Smeedia 3 жыл бұрын
Can definitely make that one 🔥
@Hajduk131 3 жыл бұрын
So I talked to IAG about the stage 3 FA20 block and trying to hit that 800 rating that they have set for that block, and the whole list of what they gave me was $16k. Seems a bit expensive if you ask me
@Hajduk131 3 жыл бұрын
Mind you that’s the long block with everything else they suggested for it.
@Smeedia 3 жыл бұрын
Long block and all bolt on parts? Seems relatively accurate for 800 WHP
@noimdirtydag9510 Жыл бұрын
Where to buy an sti with a blown engine?
@jchillchilton7388 Жыл бұрын
How much would charge me to rebuild my block for me it has rod knock I got they car 2 weeks go from dealership and I only drove it 354 miles and got rod knock:/
@DJProlificNYC 3 жыл бұрын
Biggest issue with Jdm engines are smog related. That’s why I’m patiently saving for a used usdm sti engine for my fozzy. 😕
@Smeedia 3 жыл бұрын
Very true, for states with strict smog it can also be an issue
@spheno12 Жыл бұрын
Haha I'm in this boat now. Got 180k out my 09 WRX it before it needed some big love. Now I'm trying to figure my way forward without spending 13k lol.
@siriusbreak2212 Жыл бұрын
Yeah, Uncle Rodney came a knocking on cylinder #2 about 2 weeks ago. My poor 2015 STi has a gnarly tick/knock now. Out the door (provided nothing extra is needed) I got quoted at $7.6k for a rebuild with forged internals (Manley). That's everything. Removal, teardown, cleaning, honing, new internals (forged rods, pistons, & king racing bearings), new timing belt & water pump, etc. All in all, I was expecting much worse. With that said, if you're from WNY (Buffalo specifically), I'd highly recommend Smukall Performance for your WRX or STi. He sold it to me. He installed my new ACT clutch & flywheel for a fair price. He knows his shit when it comes to these cars and I'm VERY neurotic about who I let work on my car as I typically did everything when I still worked in a shop. Alas, no lift, no way I'm doing this one 🤣. Sure, some jackstands, a cherry picker, and maximum effort would do it, but I'm getting older and don't have that kind of drive anymore. Let alone the time required. That would cut the costs dramatically, BUT... again, time. I'd need at least 3 - 5 days to do this on my own. 1 for teardown. However long the machine shop would need for honing the heads. Then a couple days on the rebuild to be sure I didn't miss anything. Yeah... don't have that kind of time available these days. Being a slave to a 9 - 5 (er' 7 - 3 in my case) 5 days a week doesn't leave much room for such ventures.the
@dougcastle1785 Жыл бұрын
Hey I saw your post. Did you end up doing your rebuild with Smukall Automotive? I want to rebuild my block to beef it up. My car runs well but I want to play it safe.
@dougcastle1785 Жыл бұрын
7.6k seems very good for that amount of work.
@siriusbreak2212 Жыл бұрын
@Doug Castle yes. Don Jr. over at Smukall knows what he's doing. As I previously stated, I'm super neurotic when it comes to ANYONE else doing work on my car aside from me. He's down to earth and does good work. Smukall gave me a fair quote out the gate, and I didn't even bother shopping past it as I doubted greatly that anyone locally was going to do better. $7.6k included a used bare block as the walls of cylinder #2 were scored beyond general repair (without sleeving it anyway). Manly Forged Pistons. King Race Bearings. Subaru OE crank & rods. Honed the heads. Valve job. The works, in short. I'm about 750 miles shy of finishing the break-in, and so far, so good!! Nearing the 3k mark of break-in oil change #2 and the level hasn't dropped. Anyone who knows EJs should find this fact rather interesting. Granted, before the motor was cooked and was eating oil like it was going out of style, but even healthy EJs have been known to chew up around 1 quart per 3k. This gives me high hopes that the rings seated perfectly and this trend theoretically should continue. One last thing, semi-unrelated, but worthy of sharing. One thing I noticed, even before the motor started to go south, it's not a fan of heat. Days where the ambient temp is above 80, even post rebuild, it runs notably more rough. That WAS the case until about a week ago when I installed the Velossa Tech Big Mouth Ram Air snorkel. This thing is a game changer! I ran the A/C full blast, 90°+ outside, and she was idling smooth as SILK. Look into it if you're not happy with summer EJ rough idles. Worth every freaking penny in my book! www.velossatechdesign.com/
@PQR5CHE 3 жыл бұрын
Maybe a silly question, but is the original engine number registered somewhere with a STI? I always hear those Muscle car guys talk about a numbers matching car. Curious if that’s something that could help a STI holding its value.
@Smeedia 3 жыл бұрын
Not so much with these cars, they made so many VA chassis subarus that I don't foresee them increasing in value with the exception of the S209 or the type RA
@josez3326 3 жыл бұрын
I just spun a bearing last week on my STi hatch.. but Im just trying to keep mine reliable and maybe just throw couple bolts ons and that’s it ... should I do forged internals or do everything oem ?
@Smeedia 3 жыл бұрын
Snag. Type RA block, pretty beefy for an OEN short block. Flat iron tuning sells them for around $1800 or so and people have made 600+ with them. Perfect for a mild bolt on platform 🙏
@independentassesor2630 Жыл бұрын
What sort of engine would you recommend for 270 - 300 awkw? Do you loose alot if bottom end Torque with an EJ207 compared to a EJ255 or EJ257? really appreciate your help 🙏
@Smeedia Жыл бұрын
Tbh I don't like 207s all that much but it's a good oem option. Personally the 257 RA blocks are the best bang for the buck IMO
@independentassesor2630 Жыл бұрын
@@Smeedia Do you have to replace the pistons on the 257 RA motors if I'm aiming for the 300 awkw mark? Can I have standard size forged pistons installed without having to home the new block, or is honing unavoidable? Thankyou so much for your input Means alot
@Smeedia Жыл бұрын
100% stock RA block will handle that just fine. No need to swap pistons 🙏
@japan8o826 3 жыл бұрын
Dude rockin a 2014 STI hatch, it’s the main family mobile, would a aftermarket intercooler or radiator be better for longevity? Stock rad seems to be holding up cooling for as well As intercooler keeping stock power for dd. Btw moving back to WA soon what’s the shop you work at, might need some work
@Smeedia 3 жыл бұрын
It's called The Mod Garage 🙏 and no need for a larger rad under daily driving conditions. If you decide to push more power then I'd suggest snagging one. But the stock top mount is pretty good
@japan8o826 3 жыл бұрын
@@Smeedia Word just more weight/ inefficient cooling? Lol to be honest just looking to turn wrenches for fun. Idk how you find time to reply to these haha
@Smeedia 3 жыл бұрын
Always try to make tike to respond 🙌🙏
@xsinfulxclutchx Жыл бұрын
Recently spun a rod bearing on my stock block 09 STi, I purchased a Type RA short block, will the stock heads work? and is there anything i should be looking for when swapping in the new short block?
@Smeedia Жыл бұрын
Your stock heads will work just fine, make sure to clean or replace the avcs cam gears and ocvs 🙏
@BushidoPhoto 2 жыл бұрын
Just spend $10,000 on an IAG long block. Done! :-)
@Smeedia 2 жыл бұрын
Sheeeeesh 😳
@twotwentietwo 3 жыл бұрын
i have an 05 sti spun a bearing...2 questions...Is it possible to make it more reliable than stock? #2 can u make it more reliable than stock while having more power than stock? (nothing crazy 300-350 maybe even 400-450 wheel)
@Smeedia 3 жыл бұрын
Yessir! Build the motor and it should be more reliable and hold more power
@anthonybarry6331 3 жыл бұрын
okay man so i have been watching your videos always ... right now i am rebuiding my 2008 sti hatch. bearing went. so i went ahead and bought a 2020 long block , which will work swapping my intake manifold . at this time i have also purchased oil uptake/baffel/AOS/fuel pump and injectors/20g turbo better intercooler and still getting a few more things like exhaust and such...but my question issssssss!!!! does the 2020 sti block have the same specs as the type RA block as i have heard since 19 they have used it in the new sti's any insight would be dope pleaseeee and right now im only trying to make a super safe 380/400 on pump. i would need to get 1300cc injectors and such if i wanted to do E85 i bellive and add the flex fuel kit.
@Smeedia 3 жыл бұрын
Yessir the 2020 block is the same as the type RA short block so you should be pretty solid for power. Sounds like you've got some fun parts about to go on the car 🔥😁
@anthonybarry6331 3 жыл бұрын
@@Smeedia oh yes man and thank you so much for the input! and ya man i learned alot from your builds and awesome information!! always so educational!! anything else you would suggest on the new build?!
@Smeedia 3 жыл бұрын
Seems like you've got it covered for the most part 🔥😁
@cityconference5130 Жыл бұрын
So just buy an already assembled shortblock and put the top end on it?
@Tony-tk4ht 3 жыл бұрын
Honestly I don’t know if my engine (ej255) is fucked. I have a tick coming from my engine, and don’t want to take it to the dealership. sounds internally, happens more when I rev it but also happens at idle. Sounds like some metal to metal and like something is loose. I have a Cobb AP and my dam and knock learns are good. Tried checking for exhaust leaks but can’t find any. The sound comes from the left and right side of the block. Any suggestions?
@Smeedia 3 жыл бұрын
Could be injector tick, the injectors can get pretty noisy at times 🙏
@milt2x 2 жыл бұрын
What is the best option to dumb it down, if I just want to get my car running, no modifications and stock power?
@Smeedia 2 жыл бұрын
Just an OE shortblock replacement, redeck the heads and send it
@Craiggg12345 3 жыл бұрын
I know I won't blow my motor. I have 95k on my stock STI. It has a Koyo Radiator, IAG AOS, GDT Cylinder 4 Cooling, and never used a Cobb OTS tune. Just had her 90-105k service done. Its getting tuned in a couple days for just an intake. I know the cars limits. Not worried about the engine blowing.
@Smeedia 3 жыл бұрын
Glad to hear! Sounds like you've got the longevity mods down 🔥😁
@beavass Жыл бұрын
Mine blew and the shop I went to swapped a type ra motor
@savage_han 3 жыл бұрын
I only swap 2JZ’s and LS ONLY no matter what platform it is 😆 jk. Thanks for that info.. It never even crossed my mind when JDM swapping. good to know!
@Smeedia 3 жыл бұрын
Anytime and LS swaps are so 2019 😉
@myroadtours6147 3 жыл бұрын
There is a guy with a 2JZ WRX, that thing is sweet!
@Grooove_e 3 жыл бұрын
Jdm Chicago has full v7 sti drivetrains for 6500, thats engine, transmission, ecu, driveshaft, rear diff, cv axles, and hubs
@Smeedia 3 жыл бұрын
Pretty much drop in ready?
@Grooove_e 3 жыл бұрын
@@Smeedia yes all drop in ready you'd have to call them for availability. Last time I checked I belive they have 4 or 5 of the full drivetrains. I'm saving up for one now to drop into my bugeye
@Grooove_e 3 жыл бұрын
@@Smeedia also the engine's are ej207
@oodles86 Жыл бұрын
Is it ok to reuse a brand new MLS gasket that has been torqued down but not heat cycled? I want to pull the head back off to fix an exhaust stud...
@Smeedia Жыл бұрын
Personally I wluldent re use them
@oodles86 Жыл бұрын
@@Smeedia thanks
@dogdog4173 3 жыл бұрын
What WHP levels should I be making on a 2.5 IAG closed deck, FP Black, 2200 CCs injectors, Flex fuel, 545 hellcat fuel pump, ETS 4 inch front mount, ELH, S2 cams, and other supporting mods ??
@Smeedia 3 жыл бұрын
Guess around 550 depending on the tuner
@dogdog4173 3 жыл бұрын
@@Smeedia ok cool that’s where I’m at. I wanted to see if my tuner was actually good.
@MonkellD 3 жыл бұрын
Any idea what you are looking at swapping something bigger into an 2015 impreza and replacing the fb20? Simple block swap or entire ecu?
@Smeedia 3 жыл бұрын
Best swap for that car would be an FA20DIT, have never seen it done but it's possible
@MonkellD 3 жыл бұрын
@@Smeedia any specific reason? Car is also cvt. I would like to use the wrx cvt if possible! Yhanks for your help! Loving that eg33!!
@Smeedia 3 жыл бұрын
You can use the CVT 🙏😁
@Brians311a 3 жыл бұрын
Do you know if you can swap a complete fa20dit engine from a 2014-2018 forester XT into a 2015+ WRX?
@Smeedia 3 жыл бұрын
I belive they have some minor differences I'd have to dig into some tech documents to find out on that one
@ranran2218 3 жыл бұрын
So idk anything about cars rly. Small stuff. So a long block is the short block plus heads. Is that what you are saying? Just clarifying.
@Smeedia 3 жыл бұрын
Correct 🙏
@masonherr5464 3 жыл бұрын
How do you know if you have a type RA short block?
@Smeedia 3 жыл бұрын
Casting number on the engine would be 706 or late model 705s. 2019+ STI comes with the RA block as well
@GAMRMNTS2 Жыл бұрын
I have a 2013 brz is it worth to ej25 swap it. I’m tired of getting gapped lol
@Smeedia Жыл бұрын
Tbh no 😅 I'd snag a second hand S/C or Turbo set up
@johnnyvittori556 3 жыл бұрын
Does the 2020 STI have the type RA block?
@Smeedia 3 жыл бұрын
Yes 🙏
@carlossgarage6867 3 жыл бұрын
Could I drop a type ra short block in a 04 wrx?
@Smeedia 3 жыл бұрын
Yes you can 🙏
@Jdaniels96 3 жыл бұрын
IAG blocks are rated by power to the crank. The numbers they provide are not at the wheels power. This is info provided by IAG themselves.
@Smeedia 3 жыл бұрын
Thats how most engines are rated, but yes good to keep in mind 🙏🙏🙏
@Jdaniels96 3 жыл бұрын
I recently bought the stage 2 tuff block, rated at 625 bhp. This will accomplish my goal of 400whp safely. Great videos keep up the good work. I follow you on the fb group as well. Honestly I’ve heard and seen proof of many ppl pushing this block in particular over 500whp. It’s just like any other engine, once you go past a certain point, the longevity of its life is shortened.
@Smeedia 3 жыл бұрын
Very true, always play it safe by over building 🔥🙏
@ericgarcia3588 2 жыл бұрын
Mine made it to 107k 😭 just got it bac after a couple months!
@IlluminedSound 3 жыл бұрын
was planning on a iag stage 2 tuff block for my 2006 sti. is that better than the RA
@Smeedia 3 жыл бұрын
Yessir, I would be more comfortable making power with that over an RA block, but thr RA is a good affordable option
@warock567 Жыл бұрын
@@Smeedia what power can you make with the iag stage 2 tuff block ? 450 to 500 whp?
@uprightmessi559 3 жыл бұрын
Yoooo lol, mine spun a bearing a couple weeks ago. Car just got towed to the shop today. I went with a short block from iag closed deck. U think I did well picking that block?
@Smeedia 3 жыл бұрын
Can't go wrong with an IAG Block 🔥 sorry to hear about the other motor!
@j3jymann 8 ай бұрын
It has been 3 years now so you know the answer to your own question. Did you do well with the iag? I'm thinking of going that way and looking at how they hold up
@uprightmessi559 8 ай бұрын
@@j3jymann Engine holding up strong @40k miles, FBO and on e85. Would buy again definitely (hoping I don't have to tho lol)
@Dave-so7sf 3 жыл бұрын
Well I guess now since I’m installing a new built block I guess I should probably upgrade my turbo too. Damn I need more fueling now to max this turbo out. $18,000 dollars and 1 year later... Damn I should of bought an engine that could handle 1000whp because 600whp isn’t enough anymore. It just never ends.
@Smeedia 3 жыл бұрын
Its always an endless rabbit hole 😅🙏
@Dave-so7sf 3 жыл бұрын
@@Smeedia I’m starting to learn to just be happy with what I have. Many people just wish.
@slaytorr. 3 жыл бұрын
I Just spun a bearing at 40K with 300HP... Big sad. Oil temps starting to increase by a ton. Looked like I was panning for gold in my oil pan. Stage 1 IAG going in Aug 10.
@Smeedia 3 жыл бұрын
Offfff 😖😖😖 at least you'll have a better block in there 🔥
@slaytorr. 3 жыл бұрын
@@Smeedia Yup, bad fincail decisions here I come.
@WickedCrispy 2 жыл бұрын
I saw a WRX going for $11,000 online. Blown motor. Everything else was pristine. Then I saw it had a CVT and I said "GOOD."
@Smeedia 2 жыл бұрын
CVTs 🙅🙅🙅
@Eric-qx7fg 3 жыл бұрын
if the motor spun a rod or bearing does that mean the AOS is toast? aka contaminated with the metal particulates and will need to be replaced as well as the oil pan, oil pump?
@Smeedia 3 жыл бұрын
No, you can pull the AOS and clean it. The oil pan also will not need to be replaced as it can be cleaned as well.
@Eric-qx7fg 3 жыл бұрын
@@Smeedia hey tanner, suppose you threw an IAG built motor in the car. What’s to say it can’t blow up within a year again? How would you be able to make the Subaru reliable. Being stocks seems to be the only way to be reliable but what about forging the motor? Would suck to pay couple grand and then a year later it blows again
@Smeedia 3 жыл бұрын
I've got a handful of videos on how to reduce knock and improve reliability. But that's always a possibility that something could happen 😖
@Eric-qx7fg 3 жыл бұрын
@@Smeedia Hey Tanner, thanks for answering all my questions. Is the stock fuel rails on the sti okay for 300 whp? heres my potential mod list: catted downpipe IAG AOS exhaust cobb AP cobb intake fuel pump fuel injectors ebcs protune could i get fuel stumble from a lack of an aftermarket fuel rail or FPR? my friend seems to tell me ill get it from this set up.
@Smeedia 3 жыл бұрын
Yes it is okay for 300WHP 🔥😁 the Cobb FPR will clean up the fuel stumble a lot as will fuel rails but it can be manageable
@JayWithDaBee 3 жыл бұрын
my motor blew at 115 thousand :( now saving for a crawford short block not trying to get crazy power so 400 hp sounds good
@Smeedia 3 жыл бұрын
Crawford short blocks are solid units! Sorry to hear about the engine failure 😭
@JayWithDaBee 3 жыл бұрын
@@Smeedia it happens man she held till she couldnt anymore cant wait for the build journey thanks for the reply!
@dkoze 8 ай бұрын
I blew my motor. Type ra block inbound
@natechave2825 2 жыл бұрын
I concur, I got married to get more headwork and it's just a non stop expense
@DarkInstinct05 3 жыл бұрын
What's up with the EG33?
@Smeedia 3 жыл бұрын
Still with outgrowth motors being built 🙏 waiting on the crank to come back to be able to assemble the block
@jkoz176 3 жыл бұрын
What if you. Blow. Ur cvt then what are ur options?
@Smeedia 3 жыл бұрын
Manual swap the car, replace the CVT, rebuild the CVT
@jkoz176 3 жыл бұрын
@@Smeedia can the cvt be rebuilt stronger?
@Smeedia 3 жыл бұрын
I'm sure there are some companies who build them, I would look i to level 10 out of NY
@E85_STI 3 жыл бұрын
Ive lost one and bought an IAG.
@Smeedia 3 жыл бұрын
Lost one?!
@LostLarz 2 жыл бұрын
Me and my brother built a bugeye pushing 20 psi like instantly lol motor blew a year after we tuned it instead of putting a new motor in we crushed the car regret it all the time
@Smeedia 2 жыл бұрын
💔😭
MrSubaru1387
Рет қаралды 366 М.
Ximei Jo
Рет қаралды 6 МЛН