Just a quick tip dude, when using heat shrink, you can use the fat barrel part of the soldering iron to shrink it instead of a lighter. 😊

from a dust storm to pouring rain... Thx for the video

Perform the LED Sync process: -Turn ignition power ON (do not start bike) -Turn 4 way hazard flashers ON -Turn ignition power OFF -Let hazard flashers run for 3 minutes -Turn ignition power back ON -Turn 4 way hazard flashers OFF That worked perfect to mine FXBB 2018.

No complaints. Looks sleeker and definitely ties in with the overall look. As for the dust storm...damn

I’m looking at getting a 2021 street bob and these videos help out a lot thanks keep it up my man

Hubby had the same issues hyperflashin with the SikTail he installed on his M8 Breakout, easy fix was to install CanBus Load equalizer pretty much screw them on and they are done, clear your codes and away you go, an easy investment of $8 each he needed 4 of them, he did a short video on my site, i ordered the same and got the load equalisers through our dealer and they are available online, cheers

Really helpful man! I just got these for my Fat Bob and was really hoping someone posted a step by step starting with disconnecting the stock Christmas tree ornaments.

nice job man, I do like those 💯👍

Had samekinds in my 06 softail many years. It need resistor to work propebly.

Congratulations on your rain!

Good job 👍🏼... but I like the stock indicators ... replaced by the white LED’s, since they stay on, more lights at night the better ...

Just fitted some of these on my 2021 Streetbob turn ign on put 4ways on turn off ign leave 4ways on for about 5 minutes then try it worked on mine

Hi mate. Very cool and clear video. I didn't know how to do, I follow your steps, and everthing is ok. Big thank from France ;) I installed Heinz Bikes led indicators which are very similar to the ones from the video. I still fail to fix the fast signal, while indicator are ok.

Sweet vid, the indicators look great 👊

Good job. Form FXBB thailand.

Nice! Peace n Luv from Minnesota

Bruh that Chewbacca scared tf outta me, but thanks for the post just got these and saw no videos on the install so thanks!

I'm not entirely sure if it makes a difference because your signals are soldered but these are the instructions we had to use to get the indicators to stop blinking fast to on my brothers 2019 Harley Davidson Street bob. Hope this helps! The BCM can self-learn once LED turn signals are installed if Hazards are active after installation. • Turn the ignition ON. Activate 4-way Hazards. Turn the ignition OFF and let the Hazards run for 3 minutes. Turn the ignition back ON and turn off the 4-way Hazards. Turn the ignition OFF and then back ON. • Check for proper turn signal operation in all modes. You may need to repeat the procedure if the turn signals still flash rapidly.

Harley has a similar looking one brand Bailey. Is there any difference?

Slick mate 🤙🤙🇳🇿🇳🇿

I disconnected the front signal plugs and just the rears worked.. then I cut the wires beside the front lights now only 1 rear works

Looks great ah!, 😎 I've got them on my 19 SG. Alot better than the stockies. Oh yeah, we finally got rain up in the hunter too, forgot what rain looked like 😳🤔 Good vid mate.

Another great concise diy vidy with no over enthusiastic presentation (thank Christ for that) stretching it out to get more adverts in or requests for likes & subs so I gave you a like & hit the sub button top job.

God mate your good at doing stuff on ya bike. 👌👌👌👌👌

That’s beauty . Who ever was the guy who disliked this video is a coward .

Looks trick👌. Under tank, usb box removal mod next??, haha

When I change the 💡 out of mine they quickly flash like that to but the light still blinks normal don’t know what’s going on but I don’t mind it

For anyone looking for some of these drag specialties makes some. I ordered from Dennis kirk. Search "drag specialties handlebar mount signals"

Gingybeard that sanding block deserves a bonus ;-) , the indicator male plug has the purple n black wires same as UK 1156 , has the main wire loom female plug a blue always live ? as im thinking of changing the 1156 turn housing to a 1157 housing . cheers

Im installing led mini indicators on my 2016 breakout fxsb and notice the bike has 3 wires purple which is the power and a black which is ground wire and a blue which is the daytime running power. Now my question is the mini indicator only has 2 wires a red and a black. Do i need to make sure the daytime running wire is connected or can i just forget about it? Any feedback would be good thanks.

Nice job, just did this mod yesterday. Your vid was helpfull. Did you manage to fix the speedy turnsignal light?

I did the same thing with my fat bob and I also had the quick flashing indicator. I found out that it is because the ecu sets a DTC for both front turn signals shorted all you have to do is clear the DTC's and it will work normal. Also if you have a fuel pack tuner you can also clear codes that way. That is How I got my signal indicator to flash properly. hope this helps.

I purchased the Ciro Fang led inserts. I needed to re-cable entirely cause the led indicators have a extra function (stays on with the main light) and therefore three/3 wires) #justsaying

Awesome job man! Loving the digital dash.. where is this from?

To fix kick flashing you must juste put WARNINGS ON, put th contact OFF, wait 3 minutes with warnings ON and after stop warnings and that's all. I did it westerday.

finally, some nice videos of Street Bob 2019. didn't you have to install the equaliser to fit the LED direction indicators?

looks good crazy expensive for 2 little lights

Did you fit load equalisers to the front indicators to remove the quick flashing issue?

Any problems with that turn lights? Does it light up the read light on the panel? Any error code?

Mate what resistor did you use and where is it located? I have Kellerman Atto DF 3 in 1 rear indicators, and Atto DF front indicators to fit. I know I need to fit a resistor but don’t know where. Cheers pal.

you should link the products you buy!!

Hey mate , I actually have the same front brown industries indicators and also the same rear wunderkind leds as you . Both are great however , I have the same issue as you with the fast blinking dash light . You will also find that when you cycle through your diagnostics the BCM fault codes come up B2146c and B2141c which translates to both front right and left signal is open . There is no fault on the rear as they were originally leds . Jus the front two . I’ve tried the hazard light sync method an no win yet . I’m guessing a load equaliser will fix it but if you have found anything that worked to fix let me know . Cheers MH . 2018 FXFBS

Hey bro where did u get ur headlight fairing and digital speedo cover from?

Hey man what size did you get the sheild stickers made in? I like the look of those instead of the stock badges.

Those nuts that connected the original blinkers, are they stock ?

LED’s looks great!! So how you liking the new Cams.?

Where did you get your tank emblems at? I'm gonna remove my stock ones.

Putting these on right now... I have 3 wires going to my stock turn signals: purple black and blue.... Think I should run the purple and blue together into the purple after stock wire??

What mirrors are those

Did you need a load equaliser mate ?

Bro if sons of anarchy came back you would be on the show !!! Keep up the mods on street bob !

those are cool but I like my running lights

Hey buddy can you send me a link for those???

Where can i get this indicator?

Any recifiers needs due to the leds?

Sik AF

$15 shipped from ebay

Try keeping the hazards on for longer....at least three minutes. Should do the trick. 30 seconds isnt long enough.

cheers lads we stock them online @ www.westcoastgarage.com.au

Cool man just about to throw some on my FatBob I used to put my mirrors on upside down too but would put the left on the right and right on the left for a better fit ✌️

Drag specialist are not that dear and brighter

Stock are better