Building a Solar Shower for use while boon-docking. My amazon Link amzn.to/2HtSxXb Power Director 17 amzn.to/2tnPsjr Canon M50 amzn.to/2SPwCA0 Sony FDRAX33 amzn.to/2EapeXG
Пікірлер: 68
@MattOphoto3 жыл бұрын
best solar shower diy video i've seen. and I've watched them ALL. thank you Ron!
@OutdoorsWithRon3 жыл бұрын
Thanks for watching and commenting!!
@xeroblastx2 жыл бұрын
I agree… and the best water stream
@ironwillie76662 жыл бұрын
Watch more videos. This build is good but there are better ways to do the water valve, create a clean out system, PVC is not UV resistant, and black paint on PVC looks horrible after just a few uses. This build is a good cheap first try at best.
@COBALTGRUV2 жыл бұрын
Thanks Ron! Keep on keeping on!
@squidless3 жыл бұрын
Nice build! If you find the pressure drops too quickly you might also want to consider adding a separate 2' section of PVC, capped on both ends, to act as a pressurized air reservoir. Simply connect an airline to your water tank and you will have more sustainable pressure during water discharge. Schrader valve can stay in place as you just need to add a small airline and fittings to connect the two tanks. Put fitting on top side of pipes to help keep water out of air tank.
@OutdoorsWithRon3 жыл бұрын
Great idea!!
@fosty.2 жыл бұрын
I thought the thumbnail was some antique elephant cannnon.
@OutdoorsWithRon2 жыл бұрын
😂😂
@oscarrebuffone63294 жыл бұрын
Hi Ron, pretty good design .I`ll be doing the same I think....just one difference....the way you put the tap.I have had to replace those taps cause they leak or broke,so in this design Iwill be putting a female fitting at the back instead of the tap, and the tap screwed to it,so if in need to replace it I can do it without breaking anything. good channel you have here. cheers
@OutdoorsWithRon4 жыл бұрын
Thanks for watching. Sounds like a good modification to make!!
@flomax_actual4 жыл бұрын
Great simple build. I'm going to borrow a couple of your ideas and adapt them to a solar shower for my Jeep JK! -Thanks Kyle
@OutdoorsWithRon4 жыл бұрын
Good luck, thanks for watching!!
@anotherone94604 жыл бұрын
Brilliantly shot video. Awesome how you transitioned the black paint shot with the mug. Great build.
@OutdoorsWithRon4 жыл бұрын
Thanks for the nice critique!!
@seansteede4 жыл бұрын
Thank you very much. one of the best designs I've been looking at. Really appreciate you posting this video.
@OutdoorsWithRon4 жыл бұрын
Thank you for watching and your nice comment.
@prioritizeyourpriorities34474 жыл бұрын
Best one I have seen
@adambarber84364 жыл бұрын
great design!!
@OutdoorsWithRon4 жыл бұрын
Adam Barber thanks!!!
@DoctorBill2 жыл бұрын
The thumbnail for this video reminds me of a Punt Gun.
@OutdoorsWithRon2 жыл бұрын
😂😂 you are right!! Thanks for watching!!
@christophervela54474 жыл бұрын
Super great video
@OutdoorsWithRon4 жыл бұрын
Thanks for watching!!!
@truecolorsbyvango80833 жыл бұрын
Real nice and simple
@OutdoorsWithRon3 жыл бұрын
Thank you! 😊
@panchitomiguel4 жыл бұрын
Good AND SIMPLE VIDEO LIKE IT
@OutdoorsWithRon4 жыл бұрын
Glad you liked it!
@daniellozana99534 жыл бұрын
How much do you pressurize it ? Also would it push out the full 4gal on a single charge or do you have to pressurize it half way through to get the full 4 gal out? Good design
@johnwren39764 жыл бұрын
Add a simple pressure guage. 👍
@OutdoorsWithRon4 жыл бұрын
John Wren Good idea!!
@huxmetalworks73714 жыл бұрын
Great job like your work can you tell me the pressure rating for the system thanks for sharing
@OutdoorsWithRon4 жыл бұрын
Thanks for watching. I don't know the pressure rating mainly because of the joints and used. Sorry.
@LuisVillalobosYT4 жыл бұрын
Nice build! I have a question, why not put the schrader valve on the filler cap instead of the end cap? I noticed some water came thru the valve in your video.
@OutdoorsWithRon4 жыл бұрын
The original idea was to be able to access all components from one location at the back of my truck. In hindsight the schrader valve would have worked better on the filler cap. Thanks for watching!!
@jocko81364 жыл бұрын
Did you use any teflon tape for the screw-in cap? I can't seem to get a good seal there. It would be fine for a shower but it doesn't hold air over a period of time.
@OutdoorsWithRon4 жыл бұрын
Yes, I use Teflon tape to seal the cap as well as an O ring in the bottom of the cap assembly. You are right it would not hold very long without either
@sgrounds224 жыл бұрын
Is this 4" diameter pipe or 6"? I really like your design. Going to use a similar design, but mine will be mounted in a 5' truck bed.
@OutdoorsWithRon4 жыл бұрын
Hi, I used 4" pipe. Thanks for watching!!
@freecatalonianow4 жыл бұрын
As a reference, how much air did you put in? What was the final pressure you felt comfortable with?
@OutdoorsWithRon4 жыл бұрын
I went to 30 PSI
@s.e.j.81534 жыл бұрын
Hi Ron - where did you find the flat ended PVC schedule 40 cap? I can only locate the curved caps and can't get a seal around the spigot. Thanks
@OutdoorsWithRon4 жыл бұрын
I think I got it from Home Depot. See this link www.homedepot.com/p/NDS-4-in-PVC-Sewer-and-Drain-Cap-4P06/100172701
@12vLife3 жыл бұрын
Nice. how quickly and into gallons does air pressure die while showering? How many times you need to reapply pressure?
@OutdoorsWithRon3 жыл бұрын
It hold's the pressure fairly well. When boon docking the showers need to be brief :-)
@ositolee58704 жыл бұрын
Why put the schrader valve low where it is covered with water and when you put the air hose on it pushes water out?
@OutdoorsWithRon4 жыл бұрын
Osito Lee good catch, the original idea was to put it low so it’s easily accessible from the ground when mounted on the truck. In hindsight it would have been better to locate it on the fill lid.
@cwr86184 жыл бұрын
@@OutdoorsWithRon good question and glad to hear your answer. building mine right now and wanted to do the schrader valve on top for this reason.
@karlosfandango5953 жыл бұрын
Good video, Ron. You rhave the same base ideas as I do. I shall however put the Shrader valve on the fill cap. My pipe is 110mm x 3000mm = 30 ltrs = 6.6 gallons. Two questions regarding pressure; what would you recommend as a max pressure to set the pipe to, and how long does it take for the pressure to drop once the shower is in use?
@truecolorsbyvango80833 жыл бұрын
Good point
@OutdoorsWithRon3 жыл бұрын
Great idea
@larryyoung20713 жыл бұрын
Why didn't you use ABS plastic which is already black? I wish you had shown how you mounted this on your roof racks.
@nicklk1324 жыл бұрын
My friend gave me their pvc shower, but it keeps leaking from the caulk around the valve anytime it's pressurized above 5psi. Does anyone know what materials or adhesives I can use to seal it up to whitstand higher pressure?
@cwr86184 жыл бұрын
id just try adding more silicone, otherwise you might have to cut it out and add another valve/lock nut/washer and silicone that one better.
@larryyoung20713 жыл бұрын
I'd recommend JB waterweld putty.
@johnwren39764 жыл бұрын
One thing, with only one removable opening there's no way to clean it out efficiently.
@OutdoorsWithRon4 жыл бұрын
Agreed, you have to get creative in finding a solution. I've found that filling it half way with water and cascade and shaking it up works well.
@toddmaggio20322 жыл бұрын
What's the maximum pressure a PVC pipe can sustain?
@alopandur2 жыл бұрын
There are regular PVC pipes not good for pressure (PVC shatters, doesn't crack so it is actually dangerous) and there is a PVC clearly marked for 220PSI at 23 C temperature.
@chummllee4 жыл бұрын
He used schedule 40 pipe that is twice as thick as the thinner wall pvc. The thin wall pipe will let the sun heat the water faster and is much less weight to handle and costs less. You want the sun to heat the water, not the pvc material. A very nice video! Thanks
@johnwren39764 жыл бұрын
But, this will last much longer in the sunlight, pressure and heat
@chummllee4 жыл бұрын
@@johnwren3976 if you are looking for long term, the schedule 40 would be better. The thinner pipe will hold up for years with exposure to intense sun and still hold up to 60psi. The cost of either pipe is minimal, ether way it is an impressive solution.
@johnwren39764 жыл бұрын
@@chummllee the thinner pipe is drain pipe and is not rated for any pressure at all. Take your chances if you wish. Pressure increases with water temp.
@cpincpersonal4 жыл бұрын
How do you know he used schedule 40 PVC? Correct me if I'm wrong but it looks like he used simple DWV pipe, no???
Depending how you water\air fill it, two drain adapters could be used. No mention made of what kind of PVC (there are at least 2) one being unacceptable for higher pressure (per plumbers on other similar sites). Personally, I would have a 30psi max. pop-off instead of the bicycle valve, air exhausted with a toothpick in the pop-off temporarily or valve. Failsafe mounting required unless you can afford prison and the associated lawsuit. Though UV resistant paint is available I would make a white sheet sleeve with velcro that can be easily removed\installed when not needing hot water anytime soon.