SOLIDWORKS Flow Simulation - Free Surface Flow

Рет қаралды 60,863

6 жыл бұрын

See more at: www.goengineer....
Learn about the new ‘Free Surface Flow’ capability in SOLIDWORKS Flow Simulation introduced in 2018. This webinar covers the setup of a Tank filling/evacuation analysis, modeling fluids sloshing in a container and using the output tools in SOLIDWORKS Flow Simulation to make realistic visuals. Webinar presented by Arunachalam Thiraviam of GoEngineer.
About GoEngineer: GoEnginneer delivers software, technology and expertise that enable companies to unlock innovation and deliver better products faster. With more than 30 years experience and thousands of customers in high-tech, medical, machine design, energy and other industries, GoEngineer provides best-in-class design solutions from SOLIDWORKS, Stratasys, CAMWorks and Agile PLM.
www.goengineer.com
/ goengineer
/ goengineer
/ goengineer
plus.google.co...

Пікірлер: 40

@bendemanish1446 4 жыл бұрын

Wow your fluent speaking skill is amazing.and of course this webinar is valuable for us.

@gungunaremusic5988 5 жыл бұрын

Thank you so much GoEngineer, it would be great if you clear one more doubt ....how can we add floating body on this free surface ?

@antonwebers8195 4 жыл бұрын

You do realize that using the mass fraction is causing an error when showing the water line? If you use the mass fraction it is basically showing you how much percent mass of a cell is either liquid or gas in your water and air case. The water has a mass that is about 1000 times higher than air and with just 10% of the cell filled with water, you already have almost 100% mass fraction of water. That's a simple hand calculation: A cell with 1cm^3 volume filled by 10% is 0.1g water and the 90% of air is 0.0009g air. This makes the cell to have a mass fraction of water of 99.11%. This basically suggests the cell is almost 100% full but in fact, it is only 10% full due to the density you are considering in your mass fraction. You should use volume fraction!

@architsaxen 3 ай бұрын

hi i want to know how we can find the volume of any container via cfd water filling?

@anthonywanjala678 4 жыл бұрын

WOOOOW...AM SO MOTIVATED

@divyeshdodiya7853 9 ай бұрын

Hey, I have sw2020 and I'm doing free surface, as per yr video bt im not getting, initial condition icon, tell me how to get that icon??

@goengineer 6 ай бұрын

Check with your VARs technical support team for an answer as the issue may be environmental to your computer.

@almeidabruno3019 5 жыл бұрын

What a great video! Have you considered doing a tutorial showing ship drag calculations or simply the free surface of a vessel moving through water? I am currently stuck in a problem like that and my simulations do not seem very accurate. I am quite sure I'm doing something wrong, but cannot seem to find the error in the setup of the problem. I'm sure this problem would attract a lot of viewers with difficulties similar to mine, as there are currently no video tutorials showing the process in SolidWorks Flow Simulation on KZfaq! Thank you for your attention!

@amitchauhan8241 8 ай бұрын

Sir is it possible to analyze mixing of co2 gas with cold water in a pressurized vessel in solidworks. Suppose a vessel is in vertical shape( 400mm diameter × 1700mm height × 3mm thickness) and vessel is half packed with series of perforated plates and then we pressurized that vessel from co2 gas up to 5 bar which will remain constant throughout the simulation or process.Consider half inch duct for co2 gas inlet from any side of vessel and then with the help of high pressure pump, cold water(2 degree celsius, volume flow rate 4 cubic meter per hour)is sprayed through nozzles from the top of vessel towards bottom. My goal is to look out how water is passing through those perforated plates and at last how much co2 gas is mixed in water which is going to be stored in the bottom of the tank . Consider 1.5 inch duct for water inlet and 1.5 inch duct for water outlet which is open to environmental pressure. Kindly explain how to do in solidworks or in ansys. Thanks a lot 🙏.

@aryanpanthri4665 4 жыл бұрын

Rightclicking results doesnt pop up anything to select transient option

@darreneagle9860 2 жыл бұрын

On the tank fill sim, why is the top tank filling and not the bottom tanks? Just from viewing the diagram the bottom 2 tanks will fill before the top 2, or am I completely wrong?

@robby95036 Жыл бұрын

Can you show how to set up the goals and run the simulation instead of skipping o the result that also has more constraints added to it?

@phreaktor 2 жыл бұрын

How accurate is the bottle sloshing animation with relation to the chemical properties of water? For example if you changed the fluid to a much denser organic solvent, would the animation behavior reflect this drastic property change made to the fluid?

@Welcome2TheInternet 6 жыл бұрын

good concise instructions. cheers

@goengineer 6 жыл бұрын

Thanks for your comment. We like knowing that our tutorials are helping others.

@said-4433 Жыл бұрын

is there any way to use fan with Free surface?

@juanpablovelezduque728 6 жыл бұрын

Hello. When I select transient explorer appears a message: No calculated parameters are found. Please specify at least one parameter in the Calculation control Options and solve the project. I really don't understand because I can see changes when I charge different time in Load time moment.

@goengineer 6 жыл бұрын

Juan, We are unsure what the source of your particular error is. We would advise you to contact your local SOLIDWORKS support company so they can initiate an investigation to help you.

@vinyldisk3382 3 жыл бұрын

i can never use Free Surface simulations, my solver always abnormally stops in the middle of the calculation. i dont have that many cells either for to fail. I dont know whats wrong

@shivakumarbairoju9050 4 жыл бұрын

Could you please do any video on Sloshing....

@ahsanaziz8343 5 жыл бұрын

great work sir

@physclubuz 3 жыл бұрын

Hi everyone, has Solidworks 2012 the Free surface option? Or only late version has this option?

@goengineer 3 жыл бұрын

Hello! The Free Surface option was introduced in the 2018 version of SOLIDWORKS Flow Simulation. Thank you.

@masterrenderermx3815 3 жыл бұрын

Can you render this?

@danielwieczorek7820 4 жыл бұрын

Hello, great tutorial. Thank you. What if the first tank is not open from the top? Why you need to add environment pressure?

@goengineer 4 жыл бұрын

Good question. As the water is evacuated from the tank, there needs to be a way for the air to fill up the top of the tank to replace the missing water. The environment pressure at the top lid facilitates this air entry.

@danielwieczorek7820 4 жыл бұрын

@@goengineer Well if you turn a glass bottle upside down, the water will flow out eventually. How can I simulate that kind of a process?

@danielwieczorek7820 4 жыл бұрын

@GoEngineer what if all founr tanks were closed? Wouldn't the liquid flow anyway?