kzfaq.info/get/bejne/mcldoMJ20tO1naM.html kzfaq.info/get/bejne/fr5dec5hr7HOkWQ.html kzfaq.info/get/bejne/gZiYZphmptjGgKs.html kzfaq.info/get/bejne/q7yklMqB05q0hmQ.html kzfaq.info/get/bejne/ittibJOZrpPZeKM.html Above video-links are all shot with this cam + gimbal (the combo as seen in this actual video - before I sold it last summer). Other videos on this channel that are +2 years old are shot with this Sony AX700 cam on a tripod. (except one other older video). All my videos are post-edited.

@@bpvideosyd thank you!

Which battery size was installed on the Sony FDR-AX700 during the test?

На этом канале 16 видео, снятых этой камерой. Спасибо

It seems not in the compatibility list. You can check here:zhiyun-website-shenzhen.oss-cn-shenzhen.aliyuncs.com/instruction/20230802/1690942379530-D7CmEhAp.pdf

No I did not. The camera is 100% balanced in all 3 axes. But I also have the top handle grip mounted, which changes the weight distribution (have you thought about that?). In addition, I have a small metal block mounted (with duct tape) under the battery for perfect balance - you can see it in the video.

Look at my thumb

Los controles del estabilizador solo funcionan en las funciones del estabilizador y el control remoto JJC solo en la cámara. Las funciones de cámara del estabilizador no son compatibles con esta cámara Sony.

Yes, that's a fair question. But these are two different worlds. As I wrote in another comment, you can compare it to a car, where the built-in stabilizer corresponds to how soft the seats in the car are, while a gimbal corresponds to the car's suspension system. The built-in stabilizer only holds the lens, while a gimbal holds the entire camera. There is a huge difference! If, for example, you walk around with the camera in your hand and move up and down relatively quickly, the built-in stabilizer cannot do the job at all, whereas a gimbal stabilizes the entire camera completely, so that the movements are not experienced in the same way. Hope this helped with an explanation.

Oh yeah, and I can add that when using a gimbal you will often disable the built-in stabilizer so that the image becomes more fluid. For example, there is a clip here of a car driving over the bridge shot with slow shutter. Several similar clips follow in the same video. These recordings cannot be made with the built-in stabilizer enabled. Because the stabilizer will then chop the image to maintain its stabilization. kzfaq.info/get/bejne/Y7l2bM10yNq2iGg.html

Maybe, - it depends on the mounting of the mic.

The camera fits nicely on the Weebill with the small batteries without additional parts. However, I have fitted a small metal block under the battery to achieve 100% balance. Pay attention to having the screen turned out when setting the balancing so that the weight distribution is correct when using the camera turned on.

@@bpvideosyd awesome. I’m sure many of us would be so grateful If you can make a video tutorial on that. Thank you

​@@andrianarisonnjato1667 Can't do that because it's all sold now. So I don't have it anymore. This video was just a sales ad link.

@@bpvideosyd still thankful. ✌️

ben crane 3 lab ıcın kullanoyorum

I think to remember that there is room for the small Sony batteries, but I can't test it now because I don't have this gear anymore.

Sí, no funcionará. No hay espacio para baterías grandes. Esta configuración requiere baterías pequeñas. 2 de las baterías (Duracell) están balanceadas con un disco de metal en la parte inferior (y cinta) para que el peso coincida con la calibración con el estabilizador Weebill. PERO las baterías mantienen la energía durante mucho tiempo, por lo que no es un problema.

@@bpvideosyd ok Gracias, tienes experiencia con algún estabilizador más grande?, estoy interesado en comprar uno para mí ax700 pero tengo puras baterías FV100.

@@urielsanchez942 No, solo he tenido este. También tiene baterías reemplazables en el mango. Algunos estabilizadores no tienen baterías reemplazables, así que yo los evitaría si fuera usted.

It's a wired remote control JJC RM-VPRI : www.aliexpress.com/item/32718633466.html The camera has built-in image stabilization, but for much better stabilization you need a gimbal. It is not included with the camera.

This gimbal is not compatible with this camera and vice versa, so therefore I use an external wired remote control (JJC RM-VPRI) mounted on the gimbal handle with strips. The cable from the remote control is, as I recall, mini-usb, which is connected to the camera's front mini-usb input (not sure if I remember the definition of the plug correctly - it's years ago now).

@@bpvideosyd Thanks for your reply! I have one more question. I use battery NP-FV70, the slightly bigger battery, does it work together with the Gimbal?

@@janeinareriksson1509 I don't know. You might have to add extra weight to the back of it to be able to balance it.

Hello again and thanks! Have you taken any video with this Gimbal, which is available on youtube?

@@janeinareriksson1509 see pinned question and answer

The cover is fixed with a pin. It's a bit like the pin that holds a watch strap. You have to press it from both sides, after which you can pull it out and remove the cover.

@@bpvideosyd LET ME TRY...TKS!

The cover is fixed with a pin. It's a bit like the pin that holds a watch strap. You have to press it from both sides, after which you can pull it out and remove the cover. On the Ulanzi I loosened the screw completely and pressed the handle down into the hot shoe - and in addition I filed a bit of plastic off the back on the edge of the hot shoe hole.

Thank you for your reply. It was very helpful.

I ordered the Ulanzi handle grips to do the same. If possible, could you upload a photo or video of the hot shoe attachment (bottom) of the Ulanzi handle grip and the multi-interface shoe of the FDR-AX700?

@@medialink7350 Can't do that because it's all sold now. So I don't have it anymore. This video was just a sales ad link.

I got it

Mine was a Ulanzi Handle Grip R005. On the Ulanzi I loosened the screw completely and pressed the handle down into the hot shoe - and in addition I filed a bit of plastic off the back on the edge of the hot shoe hole. But yes, I had to use some violence to get it in place 😁

Dévisser la vis de la molette de la poignée à font (En forcent) Revisser à font la vis sur le sabot bloquer le sabot sur un étau, scier la tête de la vis, limer la partie avant de la base du sabot afin que la poignée puisse entrer le plus en avant sur la camera.. Enfiler le sabot à sa place remettre le ressort, puis la poignée et enfin la molette serrer modérément. La partie arrière de la poignée va toucher le bord arrière sur la camera, marque l’emplacement puis démonter la poignée et limer une encoche sur la poignée afin quelle ne touche plus le rebord du trou du multi-griffe. Google translation: Unscrew the screw on the knob of the handle to do (Force) Tighten the screw on the shoe, secure the shoe on a vice, saw off the head of the screw, file the front part of the base of the shoe so that the handle can enter as far forward as possible on the camera.. Put the shoe in its place, replace the spring, then the handle and finally the wheel, tighten moderately. The rear part of the handle will touch the rear edge on the camera, mark the location then disassemble the handle and file a notch on the handle so that it no longer touches the edge of the multi-shoe hole

Si es Compatible yo tengo las dos la Z90 y Weebill S desdé que salieron a la venta y va perfecto. Hay que quitarle el asa XLR y la goma del visor y en el agujero de tornillos del asa ponerle un contrapeso para balancear el equilibrio. 👍

Hi, seriously i have no idea

Thanks! I already answered this in another previous comment - The cover is fixed with a pin. It's a bit like the pin that holds a watch strap. You have to press it from both sides, after which you can pull it out and remove the cover.

​@@bpvideosydCan you shoot a short video for this, please need it very urgently

@@webtest00 Can't do that, it's all sold. I don't have it anymore. This video was just a sales ad link.

Sim, mas o controle remoto no cardan não é compatível com esta câmera. É por isso que uso o segundo controle remoto JJC RM-VPRI preso com tiras.

Do you have a top handle grip mounted like in the video?

@@bpvideosyd thank you for your response. No I do not

​@@lymanmedeiros903 You're welcome. Well, the top handle grip changes the weight distribution (have you thought about that?). In addition, I also have a small metal block mounted (with duct tape) under the battery for perfect balance - you can see it in the video. It's all about the weight distribution of the camera. So you need to add a bit more weight at the back, so that you can push the camera a bit forward when balancing. It's pretty simple logic, you just have to figure out a way. Eg. a small piece of lead taped on can do it.

@@bpvideosyd ahhhhh yes. Add a little weight to the backside under the battery. Genius. thank you so much. Much appreciated.

@@lymanmedeiros903 Exactly! You're welcome. And remember to have the screen turned out/on when you balance the camera, if you want to use it when recording. 😉

Remote Control JJC RM-VPRI

Not necessary as the video was just a link to a sales ad. And it's all sold now...

This camera model seems not in the compatibility list. You can have a look. zhiyun-website-shenzhen.oss-cn-shenzhen.aliyuncs.com/instruction/20230802/1690942379530-D7CmEhAp.pdf

Zhiyun WEEBILL S

The grip on top of the cam is: Ulanzi Handle Grip R005 Cold Shoe Mount

Do not put top handle directly to the hot shoe! You may damage it, use a cage.

Because it was just a link to a sales ad. It's all sold now.

Nie veľa, ale musíte myslieť aj na zmenu rozloženia hmotnosti s rukoväťou Ulanzi v hornej časti. Táto rukoväť tiež mení vyváženie hmotnosti! (Google Translate)

You don't need a mic for every shooting situation 🤣 and there are def ways to mount the mic on the gimbal.

It's not comparable. Built-in IS vs. an external gimbal works in very different ways. It's like asking if a car needs suspension if it has soft seats.

It is controlled by how hard you press the zoom button

Is the top handle required for this setup to work fine?

@@Luko007 A little extra weight is required at the rear to change the weight distribution so it can be balanced. The top handle helps with that, as well as a small weight block under the battery. I have already explained this in other comments.

I just bought a Weebill S and finally got my AX700 balanced on it, but I had to add a lot of back weight (adhesive wheel weights on the battery). May I ask the model of the remote you use?

Videos on this channel are from this cam

Камера

Giá 7,5 triệu bạn