Sparex Ferguson TEA20 # 12 Fitting the crankshaft thrust bearings and checking crank end float

No video

Sparex Ferguson TEA20 # 12 Fitting the crankshaft thrust bearings and checking crank end float

Рет қаралды 11,354

4 жыл бұрын

In this video I fit the crankshaft thrust bearings and check the crankshaft end float.
Here is a link to the Kangaroo Stew where I bought it and got it running.
• Kangaroo Stew # 165 I ...
Some of the links I talk of in the introduction are below.
Queensland Tractor Spares Web Site:
www.queensland...
Queensland Tractor Spares Ferguson Parts Category Short Cut:
www.queensland...
Queensland Tractor Spares Technical Tab:
www.queensland...
Queensland Tractor Spares Downloadable Sparex Catalog Tab:
www.queensland...
Sparex Australia Web Site:
au.sparex.com/

Пікірлер: 29

@ohboy2118 4 жыл бұрын

I did ask in a previous video if you were gonna take a look at the mains/crank and hey presto. Should of known Lance wouldn't disappoint. Great series 👍

@BundyBearsShed 4 жыл бұрын

Thanks,

@johnkinnane547 4 жыл бұрын

Very good mate it was interesting I've never seen the crank like that or the thrust bearings there was bugger all movement in it when you fitted the bearings, good one Lance John

@BundyBearsShed 4 жыл бұрын

Yeah it is good to go now for sure.

@charlesvanderwolf5751 4 жыл бұрын

Thanks Lance, Good stuff, it was very interesting and well explained. Regards, Charles @ Nerimbera.

@BundyBearsShed 4 жыл бұрын

Thanks Charles.

@ryno8547 4 жыл бұрын

Cracking job as always

@BundyBearsShed 4 жыл бұрын

Thank you! Cheers!

@vincentburrowes9243 4 жыл бұрын

Lance - Good Stuff - also thank you for the technical information on the Queensland Tractor Spares Website - very helpful

@BundyBearsShed 4 жыл бұрын

Glad it was helpful!

@davidsample9130 4 жыл бұрын

Nice trick, good to see that done. And nice to know it can be.

@BundyBearsShed 4 жыл бұрын

Thanks 👍

@Spodokamono 4 жыл бұрын

Nice little video Lance. 👍👍👍

@BundyBearsShed 4 жыл бұрын

Glad you enjoyed it, nice and simple.

@peterward5723 4 жыл бұрын

Great video loaded with information. Thanks

@BundyBearsShed 4 жыл бұрын

Glad you enjoyed it!

@charleshart6992 4 жыл бұрын

Excellent stuff!

@BundyBearsShed 4 жыл бұрын

Thank you kindly!

@richardschaffling9882 4 жыл бұрын

Thank you

@BundyBearsShed 4 жыл бұрын

You're welcome

@marvinbeacham6817 2 жыл бұрын

Lance, can you guide me on a rebuild book for my TO30 Continental Z129 Gas engine? You refer to checking the book, I just don't know how to obtain the proper book. Any help would be appreciated. My compression check is about 84 dry, and 100 wet. I did not have the engine up to operating temperature when I did the compression checks. God Bless your family and pray your G'baby is doing great!

@BundyBearsShed 2 жыл бұрын

We dont have the Z129 here but the only thing I could suggest is either Steiner Tractor Parts or Yesterdays tractors possibly.

@seamusmctiernan2356 4 жыл бұрын

Disappointed you did not drop the crankshaft and renew the main bearings

@BundyBearsShed 4 жыл бұрын

Well in an in frame rebuild you usually dont and the idea of this series is to show what can be done in frame.

@timbradbury1434 Жыл бұрын

@@BundyBearsShed I have recently begun restoring a 1950 TEA20 and find your videos most helpful, I have just replaced the thrust washers as your guide, I also found I could replace the main shells in frame as well, bit of a jiggle and needs an extra long 7/16 spanner but doable.