Thanks you for the awesome feedback and honest comparison. Im not good at editing and effects but ill keey the info coming the same :)

I agree,id like to see them make that change too...

Well said my friend!

I setup all my planes exactly same :) Thanks for adding that.

In addition, I recently also decided to use the throttle cut switch to start stop timer number two as a stopwatch. I'm also playing around with using the middle position of switch F as the reset for timer 2.

Thanks Michael,appreciate it!

Glad to hear maurice! Holla anytime :)

Thanks Chris! I agree first thing i turn off :D

Thank you my friend!

Thank you for the positive feedback! Feel free to ask questions and follow me for future content :)

Thank you for watching and comment! Subscribe to see future content too :)

You have to enable the second timer. If you have and want to remove. Settings > Timer > Scroll to highlight timer 1 > Push enter with scroll wheel > Scroll right to Timer 2 > Enter on Mode > Change to Inhibit

Thank you for the quick response.

Thanks you Ken!

Thank you for watching!

Awesome! I understand these new models can be challenging sometimes.

@@BDTennessee Amen brother! 👋👋👋

Thanks bro!

Thanks for watching!

Thanks!

You can have the voltage called out through status report or on a switch. Status report is set to a value and auto called out (Choose how many seconds its auto called out). Also can be put on a switch. Mah consumed you need a add on sensor. (Part# SPMA9605)

2nd timer can be put on a switch to start and stop. Need to be setup as a logical condition which is more advanced.

@@BDTennessee Thanks for the reply. I will be looking into this as I would prefer to keep the throttle as the start action for the 2nd timer.

@@graphix-ds something to consider is making second timer activate like the first one with throttle percentage but a low value (example: 5%)...

@@BDTennessee I had considered that, but when gliding or doing thermals the throttle would be 0%. Another thing I considered was controlling the total flight timer via a flight mode switch having 3 modes:Taxi - TakeOff/Land - Cruise. Timer 2 (as stopwatch) would start with switch values 1 and 2, and stop with value 0 (Taxi). During the 20 years I have been flying I have never user, nor needed flight modes. Not sure I will be able to pick up the habit of using the flight mode switch only for the timer. We'll see. I posted the question on rcgroups, A first suggestion was to use the throttle-cut to start/stop the timer. But taxiing from/to the pits would then still be logged as part of the "total flight time".

@@graphix-ds some good points. Report back what you come up with...

Throttle timer (ie 3:00min) or the one that shows hours?

The one that shows hours. total model time

You have 2 timers built in. Model which is total time on that model and integrated which is total time of radio. You could change "One Time Active" option. Bump the throttle and then back down when starting nitro/gas motor and it will run until radio is turned off

Hallo BD Thank you for the Tip, and the quick answer Best regards Ralph

@@rallitiffany2011 anytime :)

Sounds like issue with radio.I havent heard that before or seen a setting for that

Channel Assign > Gear and Aux 2 on same switch. It will turn safe on and off however it will be tied to the landing gear. Safe On - Landing Gear down or Safe off Landing gear up. You can reverse it was well...

Preinstalled that you can use as audio events?

@@BDTennessee No, the radio already has some sounds that you can assign to each button on the radio for when you want me to say for example; (randoms on) but it assigned them and it doesn't want to work for me, has it already happened to you before?

@@hexael I havent had radio not call out audio assignments on switches. Id check volume settings.

Go through the menu shown and put them on "INH"

@@BDTennessee No Worries thank you.

Do you have it set in notification alerts? (Expiration: Tone/Vibration)

I'm not sure BD. I'm still slowly figuring it out because all I had was a dxs from a rtf carbon cub. I love the radio a lot I will have to see if I can find the settings for what you mentioned. I appreciate your time. Your videos have helped me so much

@@066motocross follow the steps in the video and i go over where im talking about. Thanks for support too!

Okay thanks buddy

Its a continuous timer for when your on the model. It can be reset,but you dont have too.

@@BDTennessee Mine starts as soon as I turn my transmitter on, even if the plane doesn't have a battery in it....

@@cricket0390 thats normal...

@@BDTennessee Thank you!!!

@@cricket0390 your welcome! Ask questions anytime!

Enter with scroll wheel > Timer > Next 3 times > Timer Control Alerts > Timer Start and Timer Stop to INH

@@BDTennessee I did that but timer on main screen isn’t counting down like it does with my aeroscout model. The f15 model is the second model I set up.

@@cG-es8mb Function List > Timer > First Timer screen scroll down to "Start:" change to "Thr.Stick" and next line should say "Over 25%"

@@BDTennessee I got it working. I know what was wrong. When I click on timer and hit the next button and it takes me to the timer clear screen. I had that set wrong. Shoot. Lol. Thank ya for your help. I have to get used to this technology.

@@cG-es8mb glad you got it worked out!