looking forward to your videos on Nose Wheel steering function, Launch assist and heading mode. Thanks for sharing

You exported the serial number, when did you download the new version on your sd card? You did not mention that. Did you download it form your computer ? Bob

Show how to access the extra channels on the NX6 cause it’s different than the 8,10

You are the best at this. Good to see you back.

Very Informative. Does it work on the IX14 Transmitter?

nice🎉

Good to see you back

I can’t get past the looks of either of these jets. Just not a fan of the lines. I can definitely see the appeal, just not to my liking. Very shark like.

I guess I hadn’t seen this video until today. It’s not good to turn the servo travel down when a surface has too much throw. Decreasing the servo travel reduces the resolution of the system and the positioning accuracy of the control surface. Servos should use their full travel in the highest rate. If the surface moves too far, the pushrod should be moved to the outermost hole in the control and then moved in on the servo arm, if needed.

Hey BD I just bought the AVANTI V2 based on recommendations from guys at my field who fly alot of edf and turbines. Yesterday I was out and flying my VIPER VS bnf with a ar631 flew great on the maiden and on the second flight coming across the field it lost signal and the plane just kept going head on into the trees and you know the rest. No idea on why or what but now its in my sanford and son parts department..lol every guy at the field that flies edf go bigger 80 to 90mm bc they fly better and easier and that maybe true but there was a failure on my receiver and that idk why. But I have the AVANTI V2 coming and look fwd to flying it. Thanks for sharing👍👍👍👍👍

is there a way to have safe come on when the flap switch is clicked - and then safe off when the flaps are up? so basically just using safe for takeoff and landings on the same flap switch?

Great video, but is this way correct for DX7S even if I have only one channel for ailerons ? (the two servos are connected in parallel). Greetings from Italy.

The Freewing appears to have larger wheels than the FMS. Would the Freewing tolerate rougher grass than the FMS?

Awesome thanks. Ive just purchased a AR637T RX with my NX 6

Is this also good as first jet?

Thank you 🙏🏿

Nice video. Thanks for the insight

Do this worh an NX8+!

Simple easy directions, Thank You!

Hello, can you deactivate the function that vibrates before turning off?

Hi, I value your tutorials on Spektrum transmitters. I have an NX8 and with the new software update from 07.18.24 there is a new menu called "hand launch assist" in the forward programming gyro utilities. I would love for you to provide a tutorial on how this works and assigning to a switch on the radio. Best. Brent

Ty Ty Ty.

When I go to the “more” section to turn off scroll sound it is a stick calibration page? Nothing about sounds at all. Any pointers? Maybe the OS is updated.

Your Spectrum Videos are the best on the net. Informative, accurate, and precise. Just been trying to find tutorials on the new nose wheel gyro feature and launch assist offered in the new as3x+ and the ones out there are complete and utter rubbish... Any chance you might fill the gap???? PLEASE!!!!

Viper летал непринужденно , за Avanti переживал от начала до конца. Казалось что не вытянет и разобьеться. А вообще круто!!!

What does this do for trim?

Another great video of what I thought was a cursed plane. I had one of these and after a couple of years of repairing the nose gear I sold it. I wish I'd seen your videos first. Dialing in that CG and tuning the elevator mix seems to have it landing really nicely without a huge amount of bouncing. I might just buy myself another one!

Hey man, I really enjoyed watching your video. You're really smooth on the sticks and have a great feel for the aeroplane from what I saw. Not bad to listen to either - cool accent. I'll sub to your channel bro!

Thank you once again bud.

I have both jets and both fly great not to mention the Albatros flys really good also.

segunda vez que me ayuda este video. gracias

But that landing!

Thank you - I was going nuts.

I was using DX8 transmitter and it was ok now I shifted to NX10 transmitter, I have now problem with response of the sticks to commands as there is a delay in execution of commands which was not noticed in DX8 TRANSMITTER

Are you going to be making any videos on the latest Spektrum update

I really enjoy your Spektrum videos , you are very direct and what’s best is that you don’t go off on a tangent and lose the thread of the subject !

Hi, I am doing a turbine conversion on this jet using a K30. Your Cg is around 15-20mm behind the factory setting, which seems a lot. Does this seem OK for you, as it looks great in the air, not tail heavy at all. Thanks!

Did you test the AS3X➕️ already on one of your birds?

Can a beginner fly this

Sir is this the same for a ix12 enjoy your videos cery much

BD I can never remember all of this stuff. And I feel like every time I come back and use the information I need to thank you again. So... Thanks again!

I went from 20se, (5 yr old $2K tx), to tx16s max2 with aluminum gimbals, to ix14. Everything I remembered from the 20 is gone. I'm the only 1 we fly with that can setup, maiden, & test others planes with the ppl I fly with. So now I'm back 50% with spektrum cause I love my tx16s! Heck, can't take it with ya🤷‍♂️🤯!

Even those these are older videos they are still very helpful!!! Question, I am looking to set up the sound for reverse thrust, or something close to that…..I’ve gone back and forth on the list….is it not there???

Everything good BD Been 5 months only checking in

Thank you I absolutely love this way!! I just have to make 1 for each size battery and BOOM!! Its gonna work!!

Love your videos, very helpful mate, I've just got my new nx8, I love it but every time I set a new model up it's all good, when I turn it off and on again all my settings have gone? Any help appreciated? Chrers

same for dx9 man?

Thinking of getting this one! Great video. Any idea how it does on grass?

When I click on next, I don’t get extra settings. I get the option to calibrate my sticks….

When i turn it on then press the button the light doesn’t turn green