Love this tutitorial, it got me out of a jam! Spider gears fell out on me, for the life of me I could figure out how to get them back in place. I gave up after 40 mins, took a break and decided to utube it. Bingo, Yukon to the rescue!!! Went back, done in no time! Thanks Yukon!
@chuckderby12953 жыл бұрын
Thank you soo much!! Ya saved me some hassle I was putting my axle back in and accidently turned it which of course made them fall out. Thanks to your video I was able to reinsert them myself
@yukongearandaxle3 жыл бұрын
Happy to help, Chuck
@johnnyturbo84602 жыл бұрын
Ha, same here.
@gerry3595 Жыл бұрын
Same
@larry47893 жыл бұрын
I used to rough and finish grind those gears and pinnions in the 80's It was a job I enjoyed too.
@mikeclough33632 жыл бұрын
Thank you for making this video. Saved me a lot of time after having a planetary gear fall out and spent a half hour trying to figure out how to get it back in. With your video it took two minutes to do. Thanks a million.
@yukongearandaxle2 жыл бұрын
Thank you for the feedback, Mike!
@adamk40036 жыл бұрын
Thanks because without this video. I would have not known how to get them spiders gears back in because i didnt see mine fall out. You tube saves the day and a mechanic bill
@yukongearandaxle6 жыл бұрын
Awesome. Glad to hear it, Adam!
@Cornfed_Off-road4 жыл бұрын
How did you get them out? Mine came welded closed
@espinoza71662 жыл бұрын
Thank you some much man I was stressing when it fell out but now I know what to do
@ernesthough11753 жыл бұрын
WOW! I've been freaking out about this. Such a great video, thank you!
@Gear1993Head4 жыл бұрын
Tip: just use some gear oil to hold the washer to the satellite spider gear while putting it in. Will keep it from falling off..
@johnranderson41843 жыл бұрын
Thanks a bunch - this had the one thing I was unclear on!
@Sergio-up5yx Жыл бұрын
🤯…….. just 🤯. This is exactly how I wish all KZfaq content was like 🙌
@stevenarcadia20363 жыл бұрын
Hi, great vid, quick to the point tutorials are always the best. One question though, which way do the flats on the side gear shaft face, or doesn’t it matter?
@MrRoy-rb1je3 жыл бұрын
OUTSTANDING!
@lonnieromero5 ай бұрын
Thanks buddy, You saved me a headache.
@johnnyturbo84602 жыл бұрын
Great video!
@JakeSchriver888 ай бұрын
Thank you!
@jeffcarpenter630612 күн бұрын
My son has a 2017 Jeep Wrangler JK. 3.73 gear ratio. He is told his spider gears need to be replaced. The ring and pinion gears look ok. Can we just change the spider gears or should the whole housing be replaced that holds them. The other thing that needs to be fixed is the pinion seal and I have to find out how to help do that for him.
@frankpaya6903 жыл бұрын
Excellent- yes, however what do you do when it's a limited slip? How do you rotate the side gears with all those clutches and discs to rotate the spider gears into place & put the pin through?
@BlueRealAmerican2 жыл бұрын
I don't know that it would help you but on those I normally put the carrier in a vise stick the axle in one end and turn it with a pair of grips. You can also do a piece of threaded rod through one end of the axle hole with big washers on each side and smash one of the gears in real tight against the clutch packs but generally helps It go in a little easier
@dberry37332 ай бұрын
THANK YOU!!!
@aaronherdt5129Ай бұрын
Is it possible to replace spider gears while differential and rear end are still mounted on the vehicle? So far every video I've seen on this subject, was always with the differential or the rear end removed and on the bench?
@meateaterwhitetail72913 жыл бұрын
I'd like to try it on my 06 fwd lifted highlander. I heard when you turn. It's open diff but when you're going straight. It locks both sides of the diffs. Definitely need that for mud and a foot of snow...
@sundusmir5 жыл бұрын
Wonderful and fruitful video. Keep it up.
@SwahgMan7 ай бұрын
My gears have some play (up and down) and just confused on if that’s normal or what can I do to fix it because I am hearing cluncking in the reat
@Keeter949 ай бұрын
Can you do this mounted on the truck still? Made a mistake and took out cross pin and turned the tire and the spiders popped off. Trying work it back in. I’m new any advice will help!!
@BlueRealAmerican3 жыл бұрын
I have never in my life seen spider gears go in that easy you must have that damn carrier grinded out so big it's unreal anybody that's actually had to do that in a real situation knows that that is the pain in the ass to do
@REsuperGRX72 жыл бұрын
Yeah I've been trying for over a hour with the diff in the truck still haha got one gear with washer but cannot for the life of me get both in with washers and lined up.
@BlueRealAmerican2 жыл бұрын
@@REsuperGRX7 just something to keep in mind I just ran into I got a brand new set of spider gears from Yukon and couldn't get the some b****** in for the life of me so when I called him they told me that the washers were replaced with a thinner washer set so they sent me a set and the spider gears went in fairly easy after that I'm not sure exactly what you got going on but if you're using new gears that may be your case too hope it helps
@REsuperGRX72 жыл бұрын
@@BlueRealAmerican stock spider gears, just was doing wheel bearings an seals. Can get the gears back in fine just seems no room for the washer.
@BlueRealAmerican2 жыл бұрын
@@REsuperGRX7 I'll tell you something you can do that might help you. Taking stick the two bigger spider gears that slide inside the carrier back inside and then run you a bolt through where the axle would go in the carrier of course the carrier has to be out of the rear end and put you some big washers on each side and a nut and tighten that gear up into the carrier that'll allow you a bunch more room to put the spider gears back in the problem with putting spider gears in is them two big gears with the clutch packs or washers on the inside of them they normally hang out and makes it hard as hell to put the washers and spiders back in hope it helps. Only do it to one side of the gear because you'll have to put the axle in the other side to turn the spider gears in hope that makes sense
@BlueRealAmerican2 жыл бұрын
Also for future reference what I always do is remove the Cross pin get the axle clips off then put the cross pin back in and doing that the spider gears can never fall out
@nathanaelszafranski39526 жыл бұрын
Works great, except how do you do it in the vehicle? The clips on the ends of the axles need to be in place before the spiders, or I will NEVER lock the shaft in. But you did show that the shim plates must go in, and that is important.
@housepumpinpc39834 жыл бұрын
Just did my first spider gear install yesterday. I'm sure you already did yours being you posted a year ago. It took me a while to realize that the gears have to be placed directly across from each other. I put the pin through to make sure. First I tried with the washers/shims. Even with grease they would fall off when rotated. I left them off until I got the gears almost in place. I installed the hardest washer first. Then installed the other. Then I rotated to the pin hole. No problem afterwards. I agree. You don't have much clearance when installing the axles and the clips with that pin in there.
@Flaco-ip7cl6 жыл бұрын
Nice video My spider gears turning fine but doesn't turn Axels
@blkbird15544 жыл бұрын
Good job buddy this really a helpful video 5 star
@AceBoy2099 Жыл бұрын
Are those washers like a spacer and "adjustable" (add or remove for fit, similar to the carrier bearing washers) or is it just 1 per side? I'm trying to figure out if i want to rebuild mine or just buy a new one from somewhere, will need just about everything, not sure about ring and pinion though. Toyed with changing the gearing while I had to have it apart but don't know how to fix speedo for it (1999 ford f150), any tips on that?
@ClintonSnow7 жыл бұрын
Thanks for the video is very helpful.
@AlohaPride_Ttv6 жыл бұрын
Im so just learning this, but i have a question, do the gears have to pressed in to its place?
@CrochetverseChannel6 жыл бұрын
THANK YOU!!!!!!!!!!!!!!!
@lawrenceanthony84042 жыл бұрын
thank you
@terryables62273 жыл бұрын
Thanks!👍
@domenicmanicone26124 жыл бұрын
I just installed my spider gears on an open carrier, when I turn the axles the entire ring gear assembly turns. Why did the spider gears not turn, they seem very stiff?
@user-hf3rq1dg9d5 жыл бұрын
Good video guys
@kevinferrell17395 жыл бұрын
does the dana 35 rear end suppose to have thrust washers behind the spider gears or can i run it without them
@YamahaVirago19947 жыл бұрын
Wow, thank u
@ra777wow6 жыл бұрын
Please Help ! I just rebuilt a GM rear, 10 bolt 7.625 .. All new gears , bearings bolts etc. I got all the specs right , pre - load and backlash etc but after installing the spider gears , I immediately noticed how it seems like there's too much play when turning the yoke back and forth by hand. Is there a backlash spec for the spider gears ? I used new thrust washers on the planetary gears , am I missing something ??
@carlosulisescampos17645 жыл бұрын
For Tundra 2002
@IncredibleHemi11114 жыл бұрын
Is there a break in period for just the spider gears
@yukongearandaxle4 жыл бұрын
No, spider gears don't require a break-in period.
@IncredibleHemi11114 жыл бұрын
@@yukongearandaxle thank you I just ordered some for my unit
@IncredibleHemi11114 жыл бұрын
@@yukongearandaxle do u guys USA standard gears for replacement spider gears for your units
@egtreadway42325 жыл бұрын
Thanks for video, my dana 35 has a lot of lateral \ in out play and alot of roaring noise while making right turns,I see no damage inside rearend and very little meltal shaving. What could be the problem. Thanks in advance
@Gear1993Head4 жыл бұрын
Don't get what your saying entirely but I would check the pinion and carrier bearings if the roaring is coming from rear. Look for play on pinion yolk.
@500hardcore11 ай бұрын
What Yukon parts are made in china
@andyboog20106 жыл бұрын
im having an issue with your sparton locker. i had it installed but when i released the pins and checked the gap i found the it fell out of tolerance. how do i close that gap
@yukongearandaxle6 жыл бұрын
Please send us a message on Facebook or Instagram and we can help you work through this issue. Also, our tech department can be reached through info@yukongear.com.
@bradc26323 жыл бұрын
I got noisy front diff 2005 liberty card. The seals have oil on them and dropped oil level. Could cv shaft bearings be issue? Noisy at 40 mpg.
@yukongearandaxle3 жыл бұрын
That's not quite enough info to do a proper diagnosis, i would recommend a qualified mechanic take a look or you can call our tech line at 425-348-9002
@bradc26323 жыл бұрын
@@yukongearandaxle are you in Utah?
@yukongearandaxle3 жыл бұрын
@@bradc2632 We are headquartered in Washington, but have distributors and installers all over. Happy to put you in contact with someone if you'd like!
@gmannubs6812 Жыл бұрын
👍
@Cornfed_Off-road4 жыл бұрын
Why do the bolts fail causing y'all to weld the cases closed?
@guspyeatt68034 жыл бұрын
if you are referencing the welded cases on our zip lockers, we weld the cases to improve durability on applications where we have seen a pattern failure due to them being installed incorrectly. lack of carrier bearing preload allows housing deflection , and by welding the cases we remove the load from the bolts improving durability and longevity. this allows us to offer the best warranty in the industry on the zip lockers,
@iroulis3 жыл бұрын
Magnets are your third, fourth, and fifth hands, or your friend.
@TheRealRemedy14 жыл бұрын
Can I use this on 08 jeep Jk rear dana 44?
@yukongearandaxle4 жыл бұрын
Hey Jay. Yes, we have spider gears available for the open carrier in the JK
@Mohamedseddek2 жыл бұрын
👍♥️♥️♥️♥️
@1stamendmentsupporter2 жыл бұрын
Music playing through the entire video is annoying.
@Jmac423 ай бұрын
Womp womp
@stevenhill43822 ай бұрын
Turn the damn radio down lmfao
@BlueGaia4 жыл бұрын
haha, he doesnt have the axle clutch in, thats why so easy! Good luck doing it once you need to puch the axle clutch.
@badcommentbot83494 жыл бұрын
Background music during the video is foolish ,I'm leaving 1/4 thru