Welcome to an extra bonus Sprue Tour, this was filmed ages ago (in Riyadh with no microphone as you'll see) and I totally forgot to upload it! So, here it is.
Пікірлер: 22
@SMAZVidoes27 күн бұрын
Thanks for the review. I have been wanting to build a BoB Movie Buchon for a long time now.
@thescalemodellingcafe24 күн бұрын
You're welcome mate
@ronaldbyrne332027 күн бұрын
Jamie, I think I would build a Buchon just for that cobalt blue colour scheme with the yellow/orange roundels. 😍
@thescalemodellingcafe24 күн бұрын
It is lovely
@kitbuster28 күн бұрын
Quite familiar with the AZ 109 G series range, radiator opening are a bit small to see anything, the cockpit can’t be fitted from the bottom you can fit the exhausts later but the worry is you Push too hard you’ll Lose them, the gear legs have a decent positive fit and create the angles pretty well , I think you’ll like it when it’s built, a bit rough n ready but builds Into a decent kit , I enjoyed building them (done 3) The Bouchon kit looks 100% same bar the nose so comments above should apply minus the exhaust fitment Good luck with the conversion , hopefully see pics of it some time
@thescalemodellingcafe24 күн бұрын
It'll be a video build mate
@clra7328 күн бұрын
The word buchón derives from buche (maw or throat), and it's given to some birds that can expand it.
@thescalemodellingcafe24 күн бұрын
Very appropriate!
@TheEdmond3028 күн бұрын
Looking forward to this Jamie, looks to be a lot of fun. And making the best of short run kits isn't seen enough.
@thescalemodellingcafe24 күн бұрын
I'll be just using the nose and armament mate
@Greg420_scale_models28 күн бұрын
What a interesting little Aircraft ,thanks for showing. Great teeshirt too . I hope you got your TP for bunghole 😀
@thescalemodellingcafe24 күн бұрын
😂
@paulmanuse235328 күн бұрын
Look forward to that build!
@thescalemodellingcafe24 күн бұрын
Cheers Paul
@whotube22022 күн бұрын
Thanks for the video, I wondered what this kit was like. I have Special Hobby 72308 - same airframe - SH looks like it might be the better molded of the two kits as the sprues are definitely different. If you encounter fit problems with mating the Eduard kit, this boxing may be an alternative route for you.
@thescalemodellingcafe13 күн бұрын
Thanks for the info mate
@justinboulton965528 күн бұрын
Lifecolour might be a good source for the blue.
@thescalemodellingcafe24 күн бұрын
I just don't get on with that stuff, I find it awful to use so I'll stick with GSI Creos which I have
@ljscalemodels52628 күн бұрын
Very interesting subject matter Jamie.
@thescalemodellingcafe24 күн бұрын
It's a funky looking thing mate. Good luck with the retirement.
@seanfoster305228 күн бұрын
I love the subject. I have the SBS conversion for the Tamiya 109. I got the nose one perfectly in a dry fit but the cannons are another story, they come as a set of PE and resin. While I got the PE on fine, the cannons are a nightmare. I ended up ordering a Mulberry 3D printed set as well as the rockets. How are you planning on adding the armenent to your aircraft?
@thescalemodellingcafe24 күн бұрын
I have that too but I'm going to try it on the Eduard kit. That Mulberry set is seriously undersized, the cockpit is at least 25% too small and the nose is 2-3mm too short in the vertical axis. I binned it. As for the armament, I'm just going to use the AZ bulges and shrouds and I'll replace the barrels with brass tube.