I really like your headlights, but you should've send wiring steps with the installation guide

I'm pretty sure wire tapping and soldering disqualify auto accessories from being called "Plug-N-Play." This is "Plug, splice (but hey if you solder it's better), watch a flippin' KZfaq video because the instructions suck so bad they refer you a KZfaq video, throw a temper tantrum, -N-Play."

Constructive criticism: This wasn't a very good guide. It should be slower with closer views of the wiring and connections - like laying them out, pointing to each wire or set of wires from the side to keep hands and fingers from obstructing view, and THEN slowly making the connection.

Once it said voltmeter with probes I turned off

Thanks for the instructions! I just installed my Spyder lights into my 2007 GMC Sierra and they look AWESOME! I used the T-tap connectors and they worked great! I did pull back the rubber cover off of the tabs, soldered the leads to the tabs and pulled the cover back over them. They work and look great! All of my neighbors want theirs changed out now! I may have to setup a shop! :-)

You put a lot of effort into making your video's professional. Why don't you actually finish the install so we can see how to do it? When you swathed from the passenger side light to the drivers side light all of a sudden there were additional wires from the truck and the lights. What's up with that?

So in the video right before he says "continue your installation not all there's still wires from the headlight hanging out unconnected to anything....so extra wires?

This video does not help at all.

Very little is soldered on automotive and motorcycle, most is done with the proper factory crimping die, the vibration caused by road travel and vehicle vibration has less chance of a joint cracking, a proper crimp leaves a tad space at the end of the wire before insulation to allow for some flexing of the wire, so if you do decide to solder, do not over solder, or solder right to the end of a terminal to allow for some flexing ability, there are some really good articles online that will explain much better the how to and wire standards with the proper die to use for any type of wiring according to the standard adopted and pull and vibration tests

I just got my halos in. trying to install them now and currently have the front end of my Silverado 2011 taken apart and can't go any further because nothing helps. they are not plug and play and its a ton more work then was made out to be in description. thank god I have friends that have done these before... but I'm still not happy that my truck is literally in pieces in my shop right now. I think spyder auto needs to work on directions

Finally!!! A video that shows how to install THANK YOU

I hate that they don’t send out instructions or do good enough videos I still haven’t gotten mines installed it’s been 3 months

How do we tell which model headlights have CFL and which LED? I don't have any CFL inverter in my car and have no desire to go searching for and installing one (since there is apparently no inverter with the headlights I'm looking at)

so you just twist the black and white wires and let them hang there?

The main flaw I see in most of these videos is, no demo after the installation

At first I was upset about having to splice cables to wire these, but once I dug into it I realized how many different things you could do the lights if you wanted. Wasn't a hard job in the long run

You just show the black and red wire being twisted around the insulation of the parking lamp wires. Anyone who knows anything about wiring would know that that's not how to connect two wires. However, anyone who might be watching this video with no prior wiring experience would be left scratching their head after doing EXACTLY what you show, and having nothing work. So far I have watched three videos related to headlights I am considering getting for my truck, and I have come to a conclusion: Your video productions leave A LOT to be desired. Your lights themselves look like they might be well made. Then again, they might suck - it's hard to tell without a decent demonstration of them in use - and by "in use" I mean normal use, not just turning them on and off in a showroom, and not showing them only from odd angles that are useless for everyday (like viewing them from above).

I installed Spyder Projector Leds on a 05 Corolla now car is Rough idling/vibrating when parked or stoped. What can i Do?

THANK YOU! I watched tons of other videos trying to install my halos but they wouldn't come on. This video finally helped! I will be posting a video of my L.E.D. projectors on my 2008 Dodge Caliber SRT-4 soon.

Would be nice if you guys could have given a schematic or wiring diagram on paper. Nothing crazy just something simple.

Very useful. Now I now where to connect led tube wires to. Just received new style led tube projector headlight for my 2009 ram. 💪

The Honda Accord Projector Headlights comes with HALO. We have two version 1 being CCFL and the other one a LED HALO both version will require you to tap the wire in to a power source.

please check the wire connection. RED=positive BLACK=Negative. First I would try to do is check if its the CCFL or INVERTER. if you do have any further question please contact our tech support dept.Thanks.

Are the inverters/ballasts included with the headlight purchase on Spyder products?

I checked today, if you wire these the way this video tells you to, your halos and led will only be on when the truck is in park, or low beams are on. Anyone with DRLs will end up driving most days in the daytime with halos and led off.

if the projector light is flickering it is you connection, check the connection in the housing to see if its loose and also check the connector from the SPYDER headlight to you oem harness

It would be nice if you could change that and make it possible to switch out the leds. I am not going to invest 300 or so bucks on headlights and have an led blow out and not be able to repair it without buying a whole new headlamp!

the CCFL rings themselves are not replaceable, however those rarely fail. usually the black CCFL inverter boxes are what fail. contact spyder auto tech support to see about a set of ccfl inverter boxes. Also, DO NOT CUT OR SPLICE GRAY/WHITE CCFL wires. Connect only the red and black wire leads from the inverter box to your power source.

you have to send instructions on how to connect the light wires!!🤔

What if my park/Corner light only has 2 wires not the three as shown in the video? Do I need to remove my fender to access my side markers to see if they have 3 wire set up?

There are warranty on our product. Please refer to our website and read the terms and condition page for a better understand of our warranty.

I bought these for mine WJ jeep and got them installed about 2 weeks after getting them. 3 days later 1 of the halos stopped working lol. There goes 250 bucks

I should really have looked futher into all this before buying.. I intend to keep and install the headlights but I can assure you I did not know anything about CCFL inverters and can honestly say I trust the company when they say mine isn't suppose to have it... just wish the small installation guide wasn't designed to make you think you needed something that you didn''t to begin with

you guys need to make updates I bought a pair of sonata headlights and had little help with how different products are now I guess with the halos and they include a black and red wire not even connected to the spyder headlight connector “plug and play” is not really a thing also my low beams do not look anything advertised on their website so be careful and do your research when buying

What if you have leds and no CCFL inverter? What do you connect the black and white wires to?

Please make a more in depth video. Chevy Silverado 2007-13 model has two sets of wires connected to the parking lights/blinkers. When you quick splice, do you repeat the process on both sets of wires? OR just to one of them? I would imagine you do it to both, but I'm not trying to F anything up.

If only your video could solder for me because I suck at it. 😆 Besides that, I have no issues with your video.

ok you put the white wires together and the black wires together then want ?

The HALO/LED are not suppose to blink when you have your turn signal light on. That is why we only have two wire 1 being positive (WHITE or RED) and the other one is to negative (BLACK)

My halos have Red and white wires.... no black ground. Any suggestions on which is hot or ground?

What about when I have 5 wires, 2 green, 2 brown and 1 black?

For that model the LED is sealed inside the housing. The light uses OSRAM LED.

The part you forgot was the other stuff that come with the wires. Where do those go.

For a Ford F-150 I basically spliced the wires so that the halo for the low lights and the LEDs come on when the low lights are on and the halo for the high light comes on when the high lights are on. But I can’t figure out a way to make it to where the LEDs and both halos are constantly on. Any tips??

Do you have to remove the front clip of the dodge to reach the headlight unit?

I have 2006 Chrysler 300..do I just hook up the CCFL Halos and LEDs to the side markers on my car?

After you twist the white and black wires together respectively, what do you do with them? just leave them hang?

Great job

My park lights only come on at night. Couldn't I tap the power from the low headlamp bulb for the LED and CCFLs? I have DRL, so if I wanted the Halos to come on during the day. Please let me know your thoughts. Thanks.

I have a 2009 Honda Civic Si and I want to install the Snyder Halo Projector Headlights. Do I only need to wire the Halos? My projector Headlights have multiple red and black wires.

I have a 2003 mustang and i installed the spyder headlights CCFL HALO but my high beams don't turn on

I have 2006 Chrysler 300. Do I just connect the CCFL Halos and LED's to the side markers?

Sir I have Toyota Yaris 2008 with halogen headlights how I change that to LED or HID wich one do you think is good for my car??

awesome... thank you!

How do you connect the leds for them to stay on because mine only turn on when I turn on the headlights.

Not good on an 2013 F150 that when set to "auto" lights, the parking lights will not come on until it starts getting dark outside. The F150 "DRL" are low beams with reduced power during the day so a splice into that line may not work well for the halo's / LED's. There has GOT to be a better way................

Very helpful, thank you

I have a 2012 Ram 1500. I followed the installation video and all went very smoothly, However my lights are very dim. Can anyone help?

Ook thanks i would check, and the thing is that i don't know how old they are

will this make the halos stay on even when your headlights are off?

Spyder Auto how am I supposed to wire the Sonar for my IS300 ? Can't figure it out from this.

How does it work on an older pre facelift e46? can't seem to find a diagram anywhere

Do the parklights stay on when the lowbeams come on? or is it one or the other? I'd like to know so I can decide weather I want my halos on all the time.

Hey spyderauto, I have a question that I can't grasp the concept of. If I hook the positive/white wire to the parking light wire and hook nothing to the turn signal wire, how am I going to get a turn signal?

I guess I don't understand what to do with the LED wires. It shows them being twisted together and left alone but if you just do that the LEDs don't work. Please help with this confusion.

bought the halo lights for my 05 BMW 325, none of the lights are only steady parking lights, all the connectors just have two wires so I'm left with picking either having the halos on with the normal headlights and just having them on at night, or with the daytime running lights which turn off at night.... unless I want them wired to the parking light/ turn signal that doesn't have a wire with steady voltage so it will blink when using the blinker....

Better use the relay for the LED set. Every time I turn on the key, then the LED will be light up. The high beam and parking does not help.

Some of the lights have replaceable LED and some lights have the OSRAM LED. It really depends on that part number.

I have the halo headlights for 2001 chevy impala and the rings dont turn on very bright. where do those wires go connected to so it can bright up more. please help

This video didn’t explain jack

My halos only come on when I have my park lights on. If I have my headlights on, they turn off. Shouldn't they always be on since they are wired to my parking lights?

Why wouldn't you include instructions and wiring diagrams for customers when they purchase headlight assemblies? Geez its a few pieces of paper that would really help with customer satisfaction

Hey I bought a 99prelude with a pair of your headlights but the ccfl won't turn so I would like to know how can I replaced the ccfl

I have a 2002 Accord and I was concerned that the headlights that are on your website (normal projector, Non CCFL) show no extra wires. Does this mean that they attach to the stock connections with no mods?

I have a 2012 Ford F150.. I don't understand how to get these into the DRL lights... the OEM Ford lights are Bi-Xenon lamps. and the DRL's run with the low beam wire... so when DRL's come on the low beam also comes on and flickers due to having HID lights.. how do you wire it so that only the LED and halo's come on the DRL and not the low beams? I know lows and DRL's run the same wire and the oter one runs high's.. The volts were 8 when drl was on and 13 when lows on.. please help

2001 Pontiac grand Prix. Ccfl halos with no LEDs. The car comes stock with DRLs and I would like the halos to be the DRLs. Right now, the projector lens comes on for the DRLs, and the inner halo comes on bright for the DRL. The projector is taking away power from the outer halo, and I would like to change this. Being that the lens DRL is straight from the socket, and the halos go through the inverter, I'm not sure how to turn the lens off for the DRLs, and make the halos the DRLs. Please and thank you!

I have a 2011 F150 with the standard OEM headlight (non-HID), to get the LEDS to work, will I need to tap into wires? I took a look tonight and noticed that I have a bulb on the side for DRL that just stays on when DRL is on, flasher bulb/turn signal bulb, and the low/hi bulb...hope that helps

What is the current draw on the accessory lights ?

Both my spyder head ligjt wont come on when engine running but will come on with engine off please somebody help me

Where can I find the male part for the inverters?

The product information should indicate special tools needed prior to purchase. The video helps but isn't as clear as it should be and this makes the artsy elements super irritating. It's very hard for me to get a shop to do things because they're closed when I'm off work. I would not have purchased this product for over $500 if I had known it is not plug and play and had difficult/insufficient instructions. I'm going to try to make this work but if I can't, I'm going to try to get a refund or reverse payment on my credit card. In any case, I probably won't buy products from the online retailer in future and I have a negative view of the brand as well. If the lights work fantastic, it will help but probably not enough for me to be a repeat customer.

For the 2009 Lancer can you replace the LEDs on that model in case one blows out????

I put mines on but my headlights didn’t quite fit

can i wire my halo llights so only me leds come on, not my halos?

More in depth video please

Are using T-Taps safe? Or will it cause corrosion and issues with the wire later on? Otherwise I'm about ready to order some new headlights and led foglights to update my truck's lighting.

Are resistors needed for the LED's & LED halos to prevent error codes? 2010 Ram 2500 Pick-up dual headlight

DO I wire the Halos and LEDS to the inverter first? Then connect the wire off the inverter to the wiring that comes off the headlight? Or do I wire the wires coming from inverter to wires coming from my vehicle?

My passenger side inverter shorted out or was not working when we first installed. Is it possible I can receive a new one?

Do I need an inverter to connect them

Can u fit hid in the projected headlights?

What if you just want the LED on as a DRL without the parking lights on? Where do I plug into a hot so can just add a switch for the DRL? Thanks.

Ive just opened up my car etc but my parking light only has two terminal instead of 3, is it meant to be like that? Toyota celica 2000

Do they come with some kind of warranty in case they blow??

9 years later, Shazam still doesn't recognize the soundtrack used smhh

I purchased ccfl halos for my 06 impala but the halos do not come on. I was wondering if the wiring process is the same for all cars/trucks because the wiring harness for the turn signal lights are connected to the oem headlight

this may sound stupid but does this set of halo headlights come with 2 CCFL invertors , one for each set of headlights or do I have to buy the 2 CCFL invertors separately ?

How would i wire ccfl halos on my 2008 honda accord coupe

I bought a set of headlights for a Dodge Ram 1500 2006 with CCFL halos I noticed when I took him out of the package there was a sticker saying caution hid bulbs not allowed why? And would be safe to run HID?

2006 Toyota Tacoma the Spyder halos came with LEDS and CCFL wires do both positive wires (White and Red) connect to the side marker positive wire,and the grounds (Black) connect to the side marker ground wire?