This is one of the best youtube builds I have seen in years. Very nice work with just the basic building materials.

As usual very informative video on the explanations !!! Simple and efficient !!! Never disappointed with all of Grain's videos

The room for optimization, is phenomenal. Nice prototype!

I thought you'd take it to the next step, seriously. Because this setup is ideal for it. The MAGIC step. 😊

Congratulations for 200 K subscribers

U are awesome. I love every project.

:) Идея для модификации, такого еще никто не делал - распилите ось пополам что бы изолировать две половины. Подайте напряжение на эти две оси. Для коммутации обмоток используйте герконы.

Great engine! Just two ideas: -Use a rivet instead of solder. -Join the magnets a little more and follow the circle of rotation of the motor. B-)

I like these motor projects

Look great!

Fantastic !

Really nice project

Spinning the coil vs spinning the magnet. If the coil was the stationary one. And the magnet spun. You would have to come up with a design where things don't touch spinning causing wear and tear on brushes because it's metal on metal contacts and it's getting hotter with sparks

Pop Rivet Copper brushes to the base, put o rings on the commutator ends and epoxy. Put a turbine fan on the shaft between the brushes and the bearing made from a solid tin snipped every few mm and bend the sections at a 30 degree angle. that will run a column of air over the commutator in proportion to the speed of the motor and enable cooling and prevent the failure. It's a fancy toy science project to produce in the unique grain manner of production. :)

вместо скрепок поставьте два подшипника, уменьшится трение, увеличится площадь контакта. красивая конструкция.

Impressive video 👍👍👍

Станислав, молодец.

MESTRIA OBRIGADO

Very good 👍👍

Awesome, so educating.👍👍👍👍😜

Incredible

I like it. Move the Neodymium magnets closer to the armature and try using the Neodymium DC brushed motor to spin a secondary armature through a weaker magnetic field (ceramic magnets). Compare the input power consumed vs. the output power of the generator that uses a weaker magnetic field.

One thing to realize is a d c motors potentially a pulse. Because of the commentators. If you put capacitors on a dc motor That are the same ferrets as the coil has inductance. You can post it at just the right frequency to where it goes enormously faster.

High current arcing is the issue here. Thinner wire with more turns on coils. Higher voltage and lower current. A vacuum cleaner motor will be a good solution to see how to do it. Many for free on the side of the road.

RIP for brusher..its not in your room but its keep in your heart😍😂👍

😂😂😂🤦‍♂️ muy bueno, saludos.

What if you had a capacitor In between the coils and commentator At the same inductance as the capacitor has capacity 1mH to 1mF

Appreciate the work you are doing. Crazy glue and accelerator chemicals are highly endocrine-disruptive. Please try not to breath fumes or get it on your skin.

It will be more efficient if you keep the field magnets more closer to rotor👍

I understan now why graphite is used

thank you clever man EGYPTION MAN

Cold fusion

MENDOCINO MOTOR uses light transferring power to three rotating panels. NO brushes, just light to never wear out.

7:45 You could have used little screws to fasten the plates and then solder them, instead of replacing them with these paper clips.

Can you make a video how to make magnetizer for reacharge magnet..you can see on you tube

Nice one

When you make the outher diameter smaller, the speed of the outher contact will be lower.

👍

你好，请问您绕的铜线是多粗的呢

How about if we use a couple of roller bearings as brushes with sprung suspension or use sprung Carbon brushes so the Commutator does not wear out easily?

👍🤓

Kontakt, Grafite!!

КЛАСС!!!

❤

why we need motion if we have circuit breaker components from Arduino programming just make a potential difference so we found it from earth and magnetic fields and with very little supply of electric current we got some more potential difference like we give neutral

Cooling is a colector

Carbon brushes will be more effective. 👍👍

هتولع الدنيا

How many turns for each coil?

Motor needs a tweety bird twiter

Hay grain ? You are working well.

How tow make motor bidine generator

Umiesz robić fajne rzeczy, obserwuję Cię od dawna

That is a lot of work to make another dc motor.

ok

Equals paradox

Equals a tink spell

i think yoy sent a part to the future thats why youwilnot find it in your room

I think he is contant

Has money

я бы купил готовый

!!~~~~~

Motor needs wind

Equals a perpetual motion machine

pfff a lot of current draining , but because gap between magnets and rotor are too big

Why couldn’t you make another coil and make it produce the electricity to run itself? You ran it on a 1.5 volt battery., that’s a very easy amount to induce. Also, why not use carbon brushes like the ones used in power tools? There’s so much more you could do with this!

First cmt.

🏳🏳🏳🏳🏳🏳🏳🏳🏳 😭

why the fuck you have low views :O

made fake

This is an old hat design with brushes and as such is very inefficient. NOT of any value. NOT SCAM but NOT ANY GOOD.

Bravo 👏👏👏👏👏👏👏👏