Static Ignition Timing On the Dyna 2000i - 93 Sportster Bobber Build - PT11
Рет қаралды 12,363
Күн бұрынAfter installing and wiring the Dyna 2000i in a previous video, it is time to set the program and timing. One step closer to getting it started!
Support me on Patreon - / cheesingarage
Dyna 2000i - amzn.to/3zHpYPv
DISCLAIMER: Links included in this description might be affiliate links. If you purchase a product or service with the links that I provide I may receive a small commission. There is no additional cost to you! Thank you for supporting my page and helping me create more content!
@antipodas1979 2 жыл бұрын
Nice. I'm enjoying this building 😁. Thanks!
@cheesingarage Жыл бұрын
Glad you enjoy it!
@BillTheHarleyGuy Жыл бұрын
great footage , i love these kind of videos. a person can learn from it 👍
@cheesingarage Жыл бұрын
Glad you enjoyed it, thanks for watching!
@61fordf2504x4 3 ай бұрын
Good stuff, much prefer Dynamic timing instead of using the LED. Would be more accurate to achieve 28 degrees as well.
@cheesingarage 2 ай бұрын
You're right, dynamic is usually the best way to dial it in but the static timing is a great starting point. I installed this before the bike was built/running, at some point I would like to do some dynamic timing to get it just right.
@IsaacCallison Жыл бұрын
Looks like in the video you are missing your "main drive bore end gear seal". I only noticed because mine just fell out. I don't know how crucial it is honestly.
@cheesingarage Жыл бұрын
Interesting, I will have to look into that. Thanks for pointing it out!
@mamined 3 ай бұрын
Hello if you have a voes but you want to disconnect it you need to put the switch 1 in position Off ? It s correct ? Can that help if you have a kickstart ? The bike have kick and electric start is a shovel? Thanks for your answer
@cheesingarage 2 ай бұрын
Hmmm, I am not sure. I would think it wouldn't make much difference at start, since it only advances with vacuum, but I haven't had the pleasure of working with many kick start bikes. I would reach out to dynatek with that question, their customer support has been great for any questions I had. Best of luck!
@Roolis77 Жыл бұрын
Liked it!
@cheesingarage Жыл бұрын
Thanks!
@joeabbott7839 Жыл бұрын
Can you get the timing like the old days by checking the push rods
@cheesingarage Жыл бұрын
I'm not sure the method you're referring to. The push rods could tell you cam and valve positions but at TDC both valves would be closed so finding TDC is easiest and most accurate through the spark plug hole.
@aaronbearden8507 Жыл бұрын
Yo! I recently installed 2000i on my 87 Softail. I have it set to curve 1. Can you explain why you say curve 4 is better? Thank you and brap!
@cheesingarage Жыл бұрын
No problem! I based this on the guys over at Hammer Performance. They are some of the leaders in performance builds for these engines and they determined through dyno runs that bringing in the advance slower is better. They have some videos here on youtube as well you should check out. Good luck with the bike!
@sugarcell4580 Жыл бұрын
Any concern that your green voes LED wasn’t on when static timing? I was installing a Dyna 2000P tonight on my ‘95 sportster that I just upgraded to a 1275. The green LED wasn’t on and when trying to static time and definitely concerned me.
@cheesingarage Жыл бұрын
I believe the VOES light is only on when the engine is producing vacuum, so it shouldn't be on when doing static timing.
@DEATHMETALCYCLE Жыл бұрын
Did you use the recommended jetting as well?
@cheesingarage Жыл бұрын
The recommended jetting from Hammer? They usually run a larger kit so I went with something more typical for a 1200. Check my carb video for details
@alexnather7614 Жыл бұрын
so how's the motorcycle lift holding up? thanks!
@cheesingarage Жыл бұрын
Still holding up great and saving my back!
@nickfury324 Жыл бұрын
Did you stop the build?
@cheesingarage Жыл бұрын
This project went on hold while I moved and set up the new garage/sorted out some problems with my daily. I am actively working on it again and should have some videos up shortly
@nickfury324 Жыл бұрын
@@cheesingarage OK..thanks for the reply and look forward to the new videos.
Cheesin Garage
Рет қаралды 16 М.
Cheesin Garage
Рет қаралды 15 М.
Octane & Electrons
Рет қаралды 92 М.