I couldn't understand a word they said. It was almost as though they were speaking a foreign language. I have both saws each with a Bark Box muffler and Max Flow air filter. The 661 has a bit more power but the 500i weighs a lot less... And fuel injection works much better than M-Tronic. I pick the 500i every time.
@cascaderetriever76182 жыл бұрын
I’m old school. I don’t like electrical sensors on my saws. I want pure mechanical
@loghog43922 жыл бұрын
@@cascaderetriever7618 I'm old school too but unfortunately when I showed up for class I found that the whole dang school was closed. LOL When ignition points left the scene and were replaced with capacitor discharge ignition (CDI) I was pretty happy and I would have remained that happy had the engineers left it at that but they just keep on engineering. The fact that Stihl now makes an MS661 without the M-Tronic available here in North America says a lot for "German Engineering". I have one on order. I'll review it on some site after I've run it for a couple months but it almost can't be worse than the M-Tronic 661. We've had nothing but trouble with those saws. The one non M-Tronic on our cutting crew was hot rodded and it appears to me that whoever did the porting went slightly too far as it's impossible to get a consistent low speed/idle adjustment out of it. All that being said, the 500i is a pretty incredible saw aside from an occasional mysterious hard starting issue. I run a 36" light bar with an 8 tooth sprocket and 75CJ chain at .035 ground on an SDM4 and HDG. It will pull a 42" bar if need be but not with command. I have over 1000 hours on mine and I'm very satisfied with it. The test in this video wasn't much of a test but still interesting. Be safe out there.
@biaschdlznep2 жыл бұрын
@@loghog4392 what means SDM4 and HDG? The other things are ok i have translatet it for me. im a german guy so i a need the metric system 😬
@loghog43922 жыл бұрын
@@biaschdlznep The SDM4 and HDG were very accurate chain grinders manufactured by the now defunct Silvey Chain Grinder Company. The SDM4 was a grinder for chisel chain bits (cutting teeth) and the HDG (replaced by the HDG6) was for grinding the rakers and the gullets that are created by the use of chisel chain grinders. I've had these grinders and used them for decades. Very precise and very well made. I mentioned this so that people would know that I'm running high quality maintained chain on my saws.
@pitt83073 жыл бұрын
Ez már géppornó Gyuri👍😊 De fasza műszerek!
@rnilazarev25533 жыл бұрын
🤝👍👍👍👍👍
@77kefi3 жыл бұрын
Jó mennek.!👍👍
@user-xv9wz4ty4o7 ай бұрын
Guiaron comprar una stihl, 500i o la ms 661cm. Para ud gue son profesionales gue me recomiendan
@andrasmolnar99373 жыл бұрын
A barátodat nem ismerem sajnos egyszer találkotunk. De a te gépkezelésed hozza az elönyt.
@istvangalambos7933 жыл бұрын
Csak az -gázokéihoz!💪💪💪
@theaxeman44292 жыл бұрын
Verdict is: if you have 462 - you don’t need nor 500i, nor 661.
@brianquigley73362 жыл бұрын
Yeah. right. My 066 pulls a 42 inch bar pretty well. Try that on yer little 462.
@johnrobertson7583 Жыл бұрын
Im sure he means bar for bar. But then again no one runs an oversize bar on a smaller just as no one carries a 22# saw around with an .043 pole saw chain.
@09rja8 ай бұрын
Don't think a 500 (or 462) can run a 32" bar.
@istra704 ай бұрын
@@09rja 500 can run up to 36 " bar. I am just buying 500 i with 32 " fitted .
@09rja4 ай бұрын
@@istra70 Thanks for the info.
@lajosnagy6913 жыл бұрын
Az 500 i gyorsabb volt.
@AntonioMarcos-iw5jc2 жыл бұрын
Husqvarna 572xp vs sthil 661
@NASCAR_NEAL2 ай бұрын
этот 661 забирает этот журнал
@daveyboy69852 жыл бұрын
Are you guy's Russian?
@tracyportersr11 ай бұрын
No, they were taking their time. 🙂
@daveyboy698511 ай бұрын
@@tracyportersr ha ha 😏
@valeriodesantis9881 Жыл бұрын
conta solo l arrotatura
@d.m_777911 ай бұрын
ms500i better
@arpadbiro7006ArmsWarriorPvP3 жыл бұрын
Srácok próbáljatok a 661-be red bullt tankolni-vagy a kezelőnek legalább pár korty jót tenne
3 жыл бұрын
A fejlesztés meglátszik jelen esetben is !
@arpadbiro7006ArmsWarriorPvP3 жыл бұрын
@ Küld el azta 661-et megnézem miért ennyire lomha
3 жыл бұрын
@@arpadbiro7006ArmsWarriorPvP nem küldhető , ez az Andreas Stihl Kereskedelmi Kft. tulajdona + M-tronic nem hiszem hogy sokmindent tudnál vele kezdeni.
@arpadbiro7006ArmsWarriorPvP3 жыл бұрын
@ Ez nem hit kérdése,reseteljétek lehet csoda történik
3 жыл бұрын
@@arpadbiro7006ArmsWarriorPvP rá lett dugva gépre , úgy hoztam el , ez ennyit tud .