Stock bottom end 351w dyno. 22PSI 80mm Turbo. Its definitely getting there.

No video

Stock bottom end 351w dyno. 22PSI 80mm Turbo. Its definitely getting there.

Рет қаралды 18,283

Күн бұрын

Website- WheelsUpRacing.ORG
Facebook
Leffie- / lowe.dj
Dakota- / dakota.kalista.1
Wheels Up Racing- / wheelsupracing2
Thanks.

Пікірлер: 62

@thuhintimidator 10 ай бұрын

Very cool. My sbe 351w made 705 to the tire on 11psi with a 7875 billet wheel VSR turbo. Ran a 9.68 at 143 at that power at 3-4k DA in Kearney NE. Then it did 9.61 at 146 at 6000 DA in pueblo Co at 14#...probably 800 or so wheel. Super happy. Keep it up!

@thuhintimidator 10 ай бұрын

Sbe 351, f303 cam, flotek thumper 185s, ported tfs intake, holley terminator, E85 and big fuel system. Took it on rocky mountain raceweek 2.0 this year. 3290 raceweight

@Wheelsupracing 10 ай бұрын

@@thuhintimidator heck ya. That’s awesome. My goal is to start doing some race weeks with it. I believe my biggest problem is I have/had my timing way too low and my converter is way off for my setup. I also think my heads have some valve sealing issues. But I’m not sure. I have to chase my tune around quite a bit sometimes. I have a freakshow converter to put in it I just haven’t done it yet cause I want to pull it apart and inspect and seal everything. So 14 psi and 706 got you a 9.61 at 146 I wonder how much power it took to get me to 9.44 at 152??? I’d like to get it back onto a dyno after I get it back together.

@thuhintimidator 10 ай бұрын

@Wheelsupracing 11psi was 705hp at 2k DA equaled 9.68 at 143. 14# was unknown hp and was 9.61 at 146 on much thinner air and a worse launch, 6000 DA. So probably 750-800 ish hp. 153mph was probably 850-900.

@mattack6779 4 ай бұрын

I am not sure what is meant by "stock bottom end" but I doubt stock cast pistons can hold up to 22lbs of boost for very long even with perfect ignition timing and A/F mixture. I won't even mention detonation. However, a 351 Windsor block, crank and rods are capable of holding up to the extreme pressure of 22lbs of boost if the engine is tuned right. Nice build Bro!

@Wheelsupracing 4 ай бұрын

Stock bottom end I’m referring to exactly that. It’s a completely stock bottom end down to the bolts. Went 9.44 154. Tuned by me. Ended up taking the main bearings out because of rpm and cap walk.

@dereksmith3780 10 ай бұрын

Stock 351w bottom end is pretty stout. I was running 20-23 psi on my lightnings stock bottom end with 206k miles. Ran a 6.4 in the 1/8 blowing the map line off the ECU. Probably a high 9 second truck at 4500lbs. Got that motor on stand now in retirement.. never broke anything.

@Wheelsupracing 10 ай бұрын

Heck ya. That’s awesome. I do think the lightnings had either hypo or forged poisons where all the others had cast pistons. That’s moving for a truck for sure. They are definitely stronger than people give them credit for.

@dereksmith3780 10 ай бұрын

@@Wheelsupracing they had hypereutectic pistons. But from what I understand they weren't lightning specific.

@Wheelsupracing Жыл бұрын

@Lingen Bully not sure what happen to your comment. It has brand new valve springs. I found an alt wire that was chafed and the alt was acting up. On my drive home the alt took a crap completely. Installed my spare alt and it runs 100% better. gonna gap my plugs down a little and add a few degrees of timing and that should really wake it up. im running on winter blend E85 so i have the the timing really low. 22 psi was a whopping 12 degrees all in. Gonna turn it back up to 14 degrees and go from there. really wish i would have been in the car on the dyno because i would have loaded the car harder from a lower rpm. i also found a cold side boot that was torn some. im not sure if that happen on the dyno though.

@Go4BrokeOffroad 10 ай бұрын

pretty good numbers sir. dig the build.

@Wheelsupracing 10 ай бұрын

Thank you. It’s probably making more power now but hasn’t been on the dyno. This winter it’s getting tore down and built.

@joeykimball5705 Жыл бұрын

Fuck the haters man. Love the car

@Wheelsupracing Жыл бұрын

Thank you!!! i left a lot of power on the table in timing alone. Im ironing it out and when i have some more time i want to put the car back on the dyno and do some real tuning. As of now ive put 4 degrees in my entire timing table. i didnt have nowhere near enough timing in it. That could also be why it sounded like it was laboring really bad. Besides haters gonna hate. Dont see them out having fun with a car they built with their own hands.

@joeykimball5705 Жыл бұрын

@@Wheelsupracing damn right.

@brawler3475.0 10 ай бұрын

Mine made 630 at 12 lbs with 22 degrees of timing but your getting there

@Wheelsupracing 10 ай бұрын

I dunno how much hp mines is making now. Enough to go 150 plus in the 1/4 back to back runs.

@mike4fo 8 ай бұрын

Glad u fixed it 💪🏼

@BigStickStangs Жыл бұрын

Nice! Making good power 💯

@Wheelsupracing Жыл бұрын

Track times say its making more power than the dyno says.

@brawler3475.0 10 ай бұрын

Hay man don't listen to all the bullshit haters and key board bangers your out there doing it i have a sbe 351w making 630 wheel check it out

@Wheelsupracing 10 ай бұрын

I’ll check it out for sure. Ya. The dyno is for finding issues and that’s exactly what I did. It’s been 152 in the 1/4 and at 3450lb it takes good power to do that. I love the people that put down 1000hp on the dyno but go to the track and run 11s.

@slopoke22 8 ай бұрын

I dont have a stockBE but i do have a stock crank Windsor that goes low 5s on nitrous and is a street car

@Wheelsupracing 8 ай бұрын

Heck ya. That’s awesome. I believe I could have taken .5 second off my time with a better converter. I also believe my heads have had issues for quite some time. Found some stretched valve stems when I pulled it apart this winter. I had 7 exhaust valves that were leaking badly and that’s a lot of HP left on the table.

@Wheelsupracing 8 ай бұрын

Mine went 5.94 with a 1.54 60’ and a 3.27 rear gear 28” tire cause mines geared for the 1/4. That was on 20 ish psi. Converter was very tight and didn’t flash when I left the line. I rode the converter all the way down the track so the car was sluggish. Now it has a freakshow custom converter and a 393 will be going back into it. Should be a whole new animal.

@slopoke22 8 ай бұрын

Nice. I've been a 5.39 @129 1.19 60' on a 275/50/15 mtDR. I hit mine with 425. I can drive 55 fine but after nah, lol. But bet I'll drive it a long way @55 if I need too! I'm about to just give in and take the gear out and turbocharge, so I can get much better street but I'll miss the sound and feel!

@mike4fo 8 ай бұрын

🔥

@mikemcdonald2975 10 ай бұрын

I made around the same horsepower level 7 psi there's something definitely wrong

@Wheelsupracing 10 ай бұрын

There was a couple of issues. That’s what the dyno is for. Ended up running 9.44 152 at the track. Had a few boost leaks causing the boost to not come in till right at the end of the pull and the Holley was doing some weird stuff with the rev limiter.

@veejay120793 Жыл бұрын

Do you just monitor knock by ear? Or did you add knock sensors?

@Wheelsupracing Жыл бұрын

It’s on e85 so it’s very hard to make it knock. I read the plugs for timing though.

@mike4fo 8 ай бұрын

Did putting in a new alternator fix the problem ?

@Wheelsupracing 8 ай бұрын

It sure did. Between having alternator issues and some large boost leaks. Plus the Holley rev limiter was doing some funky stuff.

@Iandiorio1 Жыл бұрын

Had the same issue years ago with a 3g alternator and it would somehow phase out at 6500 and up rpm Call to PA performance and they over built a 200 amp alternator for us.

@Wheelsupracing Жыл бұрын

That's very similar to what this one is doing. i put my spare on it and it seems to be running much better. I've been told it has something to do with the diodes.

@Wheelsupracing Жыл бұрын

im thinking about switching to a 1 wire in the future.

@Iandiorio1 Жыл бұрын

Did you do a total seal gapless ring or or least a basic moly ring pack with a bigger end gaps? Or is this 100 percent stock down to the cast rings?

@Wheelsupracing Жыл бұрын

Rods, crank, pistons, bolts and bearings are all how it came from ford in 1995. i didnt even pull the pistons out.

@rgsteele83 Жыл бұрын

That's pretty amazing to me being all stock. I'd call that a true budget and good hp per dollar. May not hold to long but that doesn't seem to Be huge concern for you. I'm sure you do get a little tired of pulling a trans or motor, But I'm right there with you with my setup. Mine could let go at any moment I'm sure

@Wheelsupracing Жыл бұрын

@@rgsteele83 it does get old but I pulled the motor once in 2022 to freshen it up so not a huge deal. That’s kinda part of the fun. See what you can do on a complete budget. Sure I could have my forged stuff machined and put into a block but as I’ve learned that just makes the block the weakest link.I did finally get tired of pulling the trans so spent a little money on a C4 and a good converter. But still budget stuff. Not like I dropped 5 grand. I got the entire trans setup for 2000. Shifter cooler and all. Didn’t have to buy anything but fluid.

@rgsteele83 Жыл бұрын

@@Wheelsupracing I'd like to try a c4 In a foxbody at some point.

@Wheelsupracing Жыл бұрын

@@rgsteele83 I like mine so far. Got tired of the 4r70 burning up.

@vrm86gt Жыл бұрын

were all pulls at 12 degree?

@Wheelsupracing Жыл бұрын

no timing gets progressively pulled out per psi. after doing some research and looking over my tune im way too low on timing. I've put 4 degrees of timing back in and that's probably still not enough. i want to get it back on the dyno when i have more time to do some actual tuning. i also found a boost coupler that had a nice sized hole in it.

@vrm86gt Жыл бұрын

@@Wheelsupracing cool!

@Blackjack_focus_st3 Жыл бұрын

More like blown up racing

@Wheelsupracing Жыл бұрын

Hell ya. I like it🤙❤️

@Wheelsupracing Жыл бұрын

Good thing I drove it to work then the dyno then back home.

@jimmytreadway3195 Жыл бұрын

something is terribly wrong with that car ,no where near what it should do

@Wheelsupracing Жыл бұрын

There was a couple of issues. That’s what the dyno is for. Ended up running 9.44 152 at the track. Had a few boost leaks and the Holley was doing some weird stuff with the rev limiter.

@logut80 10 ай бұрын

@@Wheelsupracinggood mph, ET is about .5 slow vs that mph

@Wheelsupracing 10 ай бұрын

@@logut80 yeah at this point I think I’m just having a little bit of a combo issue. The converter is not right is probably my biggest issue having a really hard time cutting a good 60 foot 9.44 at 152 with only a 1.5,60 foot.

@joshuagarvey9362 8 ай бұрын

Trial and error man.Takes time.

@Wheelsupracing 8 ай бұрын

@@joshuagarvey9362 got a converter and engine is at the machine shop now. Going back to a 393. Beat the bearings up on the mains of the stock bottom end and wasn’t going to spend the money fixing the stock stuff.