I Almost Gave Up!

Рет қаралды 20,581

22 күн бұрын

I Almost Gave Up! Keeping equipment up and running on the farm is a big challenge...but today we're finding the best tools for the job! Hope ya'll enjoy! #tools #farming #broken
Tools Used today: www.amazon.com/hz/wishlist/ls...
Tools/Goodies on my Amazon page here: www.amazon.com/shop/stoneyrid... (Stoney Ridge Amazon Affiliate Page)
‪@LockNLube‬ ‪@gehl1859‬ ‪@hondamotorcycles‬ ‪@Truewerk‬
As an Amazon Affiliate Associate I earn from qualifying purchases.
This Video is for entertainment purposes only.
Stoney Ridge Farmer videos may contain paid sponsorships.

Пікірлер: 140

@oldtimefarmer3405 14 күн бұрын

Famous last words I trust this machine 😂

@leer-winnobbeefarms2131 14 күн бұрын

One of our neighbors, just down the road, raised the bed of his dump truck, then proceeded to lay across the bed rails to grease a fitting. As he lay there, a hydraulic hose burst and he is forever dead. He left behind a young wife and a very young son. If a hose breaks, whatever it is that's up in the air, is instantly on the ground, faster than you can blink. I'm a farmer, and yes, I've done it too, but it's not a good idea. You are betting your life on a hose. Lee

@yoyoswift9926 14 күн бұрын

Josh I cringed when u were working under that bucket. One of the reasons I love your channel is your safety habits. Please be careful n find a safety precaution to put in place❤

@michaelbaker2363 14 күн бұрын

Grease gun to shoot grease in ball joints and tie rod ends and does not have a grease fitting that you can shoot in around the edge of the rubber

@davidneely1749 14 күн бұрын

Josh, great Tool Tuesday share, always appreciated. PLEASE, ALWAYS use a mechanical jam when working under a hydraulically lifted machine. If a hose were to fail while you are under there working you are a dead man walking. Maybe you were using a mechanical jam and if so, please share with your audience from a safety perspective. Thank you for an excellent channel, I enjoy it very much!!

@barrytaylor3278 14 күн бұрын

FYI......... In the future use a heat gun (I have a 20V Dewalt Battery one) and use it to heat the joint until it gets hot, (no flame worries) then try greasing it or use the impact greaser with half and half penetrating oil and grease mixed together.... Works every time! 😁 Also....hard plastic mallet works better...or a steel hammer..... I use a small 2lb sledge hammer...

@malibusbc 14 күн бұрын

French press coffee pot, paid $20 and works great...no expensive coffee maker

@lynnhoskins5286 14 күн бұрын

josh man use a pressure treated 4x4 or 6x6 you should not trust it ever period

@bobearl7859 14 күн бұрын

That needle is for greasing non greasable bearings

@ctgoss7207 14 күн бұрын

Hey if you will fill it full of greese until it builds pressure then make your bucket go up and down it will grind that hard piece of grease down and let the fresh grease start the flow

@truehill51hill72 14 күн бұрын

For a safety jack for your bucket find a old car jack and a piece of pipe to fit over and down on jack cut to length. Jack until tight.

@ProjectsWithPaul 14 күн бұрын

Fluid Film is great rust preventative but its hard to beat Kroil for stuck nuts and bolts. Love the Lock N Lube.

@chipprice1174 14 күн бұрын

That needle is very handy. I use it on my shop roll up door, to get in tight places that has a contact surface, but no grease fitting. I also use it to grease bearings, by just sticking it in between the roller bearings, and give a few pumps till it comes out the other side, repeat all the way around, and you have a perfectly greased bearing.

@jamespinckard4210 Күн бұрын

Red-n-tacky.................good stuff. Been using it for quite a while. Never have had a problem with it.

@bcgrittner 14 күн бұрын

Lock and Lube is a superior product. Story: Back in the early 1970’s I had a foreign motorcycle with strange grease fittings on the rear suspension swingarm bushings. John Deere sold a grease fitting with metric threads and American style “zerk” fitting on the business end. Dirt cheap, and no more searching for the grease needle. Show and shine judges never noticed those fittings.

@scottsmith6846 14 күн бұрын

Hey Josh thank you for the video and when you hit that grease gun I thought it came with that noise woo

@LukeA_55 14 күн бұрын

What perfect timing, I was under a bale mover for a couple hours yesterday fighting 2 fittings that wont take for anything. I pulled the fittings & shot grease through them, then sprayed degreaser inside and moved it up & down trying to break up the old grease. Tried the grease gun in all different positions along its motion but it just will not budge. Imy gonna have to take a shot with that grease buster

@drew1381 14 күн бұрын

Lock'n'lube has been the best I have used for both grease and air chucks. Highly recommend. They are expensive but in hassle and broken fittings they are worth it to me. If you use a grease gun for a farm/ ranch or commercially looki into them.