Stripped bolt/cross threaded bolt SUPER FIX!!! Great great video!! Super Trick

Рет қаралды 328,989

4 жыл бұрын

So this is the video that I wanted to do. For a number of years this is one of my super tricks I don’t use it very often because I don’t make the mistake of tightening up my bolts before they’re all started which is the mistake that was made in this particular situation. But because the mistake was made it allowed me to make this video so this will be extremely helpful to any DIY at home Auto Repair. And I hope you find the serious value of even watching this even if you’re not having this problem today so please share the video give me the thumbs up I greatly appreciate it God bless and have the best of days I hope you enjoy the video.
⭐⭐⭐⭐You can further support us by using these links to purchase anything from Amazon! So here's some things we like to have around the shop! (you can buy anything with these links and it helps us out, not just the linked items)
FOXWELL Car Scanner NT604 Elite OBD2 Scanner ABS SRS Transmission, Check Engine Code Reader,Diagnostic Scan Tool: amzn.to/3vmTYhu
60 PCS Tap and Die Set Metric and Standard Sizes: amzn.to/3MkcFtl\
Craftsman 20 Piece 1/4 Drive Metric Socket Set: amzn.to/3xEltpy
CRAFTSMAN Hand Saw, 12-Inch Hacksaw (CMHT20138): amzn.to/3uUijfE
#Stripped #Strippedout #strippedbolts #crossthreaded #strippedhead #crossthreadedbolt #TheClayWay #Howto #tripsntricks #possiblecauses #Chevyequinox #FordF150 #FordEscape #Fordexplorer #Fordexplorersporttrac #Chevysilverado #Chevy #Ford #Pontiactorrent #Saturnvue #BMW325XI #BMW #Volkswagon #volkswagonjetta #volkswagonbug #dodgeram #Jeeppatriot #jeepliberty #Mazda #jeep
“You can’t really break it if it’s already broken!”
Please subscribe!!!
if you want to reach out to me and get a message to me hit me up on clays ac and auto repair on the facebook And if you have any questions it’s easier to message me straight through Facebook
Why should you Subscribe to my channel ? I constantly make these videos that show you how to use your tools and show the techniques that we use in our auto repair shop every day. And all it does is help me send you stuff . I do not sell your information I do not solicit you. all it does is add a couple 100 thousands of a cent to me . And it cost you Nothing ! you would only be helping me . And hopefully i was able to help you !! So please be kind and enjoy!!
I am not responsible for any damage that happens to your car or if I am incorrect about any of my information contained in my videos or any accidents that happen while you’re performing the procedures that I explain , I will not be liable.
Products that I use quite often.
PB blaster penetrating oil
Lisle tools
Snap-on tools
Matco Tool‘s
Dorman Products

Пікірлер: 150

@mostlymoparih5682 Жыл бұрын

Kittywampus. I love it. Words that I use, no interpreter needed. Kittywampus by the way is not liked by spell check and they wanted me to use hippocampus. Oh and in case you're askin, what the heck is that well it's a major component of the brain of humans and other vertebrates.Humans and other mammals have two hippocampi. And here I thought this was a video about fixing cars. Go figure. Dang ya gotta watch your videos a couple of times to listen to you and to read all the jokes and tidbits well make that Claybits. Happy Motoring.

@luisrew12345 3 жыл бұрын

Worlds loudest intro 😂😂

@kentfellers 4 жыл бұрын

Great trick......but your jokes running along the bottom are the most irritating thing I've ever seen.

@eliasmd2003able 4 жыл бұрын

Yes.

@BigTexVet 4 жыл бұрын

Agreed

@joseguzman5871 4 жыл бұрын

I'm sorry I'm just trying to see who asked?

@tyyup617 3 жыл бұрын

Andrew dice clay wannabe

@jimmorrison1553 3 жыл бұрын

@@joseguzman5871 KZfaq brah! Turn off comments if not interested in feedback. Better yet go back to your MySpace

@ferenctulics9688 3 жыл бұрын

Excellent idea! Only one mention: next time cut the bolt in the direction of the vise, not sideways :-) Anyhow, great tip!!

@liaqathkhan5509 4 жыл бұрын

so smart idea thanks

@gergemall 3 жыл бұрын

Love your channel. You’re a great teacher and interesting man .

@sharpcarco 3 жыл бұрын

Thanks John we love you too brother

@ledssagosa8640 4 жыл бұрын

Great video and great technique

@02gtsaspis6 4 жыл бұрын

This got me out of a pickle! This is genius!! Thx 👍

@KoowlFuryMusic 3 жыл бұрын

Great video!! One of the thermostat housing bolts on on my Town Car wouldn't go all the way in. I used a vice grip to hold the bolt (kinda bootleg but it worked lol), used my foot to hold down the vise grip, and carefully cut down the center of the bolt (not too far though). I was actually able to hear the bolt re-cutting the threads as I tightened it down. Now my Lincoln is back on the road like it should be! Glad I saw your video!

@sharpcarco 3 жыл бұрын

Well what you did was not as much bootleg as me making this video. This is some serious von hackery ...... i’ve had a lot of negative comments. But I don’t see where in certain situations that this is not a useful tip just like your situation nobody’s life is going to be in danger..... but people have said I’m trying to kill people...... Anyways I think it’s awesome that works for you

@jegr3398 2 жыл бұрын

Put. The. Vice grips. Down.

@186scott 3 жыл бұрын

One thing you forgot to mention and say is it turn the bolt into a tap and re-taps the threads but at the same time the strength of the bolt is also comprised so if you are doing that make sure once you have repaired the thread to replace the bolt with a new one

@baine5.7 Жыл бұрын

I was just going to say dosen't that compromise the bolt strength, im guessing yes ,it that particular one application probably won't matter because that looks like power steering pump ,but im pretty sure in any place it has stress on it ,tap and die would be needed, but im just guy who's been working on vehicles since I was 15 ,now 42 .

@albertwebber1153 4 жыл бұрын

My favorite new word - kittywompus! :0)

@petropete3122 8 ай бұрын

Nice one 🤙🏻. Tks for sharing 🍻

@josephhartke454 3 жыл бұрын

I just spent about 30 minutes cutting into 3 bolts ya know, for variety, and then turned the first one all the way down with a stubby ratchet the whole time shouting "WHY IS THIS WORKING?!" so thank you

@honeybear8485 3 жыл бұрын

I actually ended up using the copper strands into stripped bolts on my transmission pan that when I took out the bolts that aluminum shredding was right on the bolts so I'm going to get a helix coil repair kit but for now it definitely slowed it down thank you man tightened a bolt up really good

@sharpcarco 3 жыл бұрын

I think Healy coil‘s would be appropriate in that situation for sure this is more of a technique you use when you have no other option.

@honeybear8485 3 жыл бұрын

I agree absolutely brother . Kind of like using the zip ties.. to hold your throttle cable.. for a little while. Lol but yeah definitely.. in a pinch it definitely it definitely slowed the leak down thanks again I appreciate it..

@DS1JohnB 4 жыл бұрын

I tried this today and it worked great, I had to use a cutting wheel though, the bolts were too tough to cut with a hack saw.

@sharpcarco 4 жыл бұрын

Definitely took me some time to cut through them with a hacksaw but that was OK I had an 18-year-old kid doing it for me LOL

@baine5.7 Жыл бұрын

we had dodge work truck big Cummings, great motor, but it went through pads and rotors ever few months crazy .

@sharpcarco Жыл бұрын

I have a good friend of mine that does newspaper delivery for a living and it seems like every three or four months I’m putting brake pads on her car.

@happyhealerforpresident2029 4 жыл бұрын

thanks

@SeanThompsonDC 2 жыл бұрын

You know why I subscribed to this channel? Because he said 'catawampus' ... That is a technical term too few professionals use these days.

@olenaerhardt7725 6 ай бұрын

@ 1:25 I replaced yesterday Rear strut on 2003 Chevy Cavalier and it looks like one mounting bolt got crossed. Exactly how it is shown in this film it can't go further. I think to come from another side to clean the threads in the hole (the bolt is supposed to go upward, and it is crossed, so I'll try to send it from top to bottom). If it won't help I'll try to cut it. Interesting technique shown.

@c.l.e.a.n.nation 4 жыл бұрын

I just appreciate the trivia running across the screen 😂

@meezylife673 3 жыл бұрын

Super helpfull

@sharpcarco 3 жыл бұрын

Super thankful you took the time to write the message thank you very much

@honeybear8485 3 жыл бұрын

Wow that was definitely wicked sick man like some kind of Weird Science Magic😀😀

@sharpcarco 3 жыл бұрын

Yeah sometimes I create Kelly Lebrock’s in my basement

@honeybear8485 3 жыл бұрын

Oh really well I'd like to see a video of that lol funny ..

@bobbytables4305 Жыл бұрын

Fix one problem with a different one. GENIUS. Srrsly don't do this...

@sharpcarco Жыл бұрын

The guy that can’t spell seriously is telling somebody seriously not to do something…. Apparently he doesn’t understand or didn’t pay attention to the video of why exactly I did it… this is not the way to fix things properly, but some people don’t fix things properly… and this was one of the very few instances that I could actually do this with no fear of it affecting anything…. And I wanted to show people a different way of doing things if they felt they were in the position to not fix them correctly…… thank you for your input just go watch other videos and make yourself feel better about commenting on them, pretending like you actually know something…..

@bobbytables4305 Жыл бұрын

@@sharpcarco Nice Ad Hominem. You are literally altering the material properties of a hardened bolt. Instead of doing it the proper way. 🤦‍♂But, hey have fun with your negligence lawsuit.

@energyasylum997 2 жыл бұрын

@1:23 “The bolt won’t go down for crap???” ……. My toilet acts the same way when it’s plugged!! (😂)

@handidrummed 4 жыл бұрын

Came for the fix, stayed for the puns

@tangedal9983 4 жыл бұрын

Great tip and video. The bolts to my thermostat housing just keep spinning and won’t tighten down. Will this work to actually get them to tighter down. Because they just keep spinning and it causes leaks when engine is running. Please help.

@sharpcarco 4 жыл бұрын

No regretfully you will have to retap the hole or helli coil them sorry

@jegr3398 2 жыл бұрын

Your bolts are broken. Good luck LMAO

@AgeofReason 4 жыл бұрын

Excellent tip. Sawing down the bolt is a workable temporary solution. Interesting. Any tips for removing a bolt installed with a stripped thread?

@sharpcarco 4 жыл бұрын

Actually I have a pretty good way of getting them out kzfaq.info/get/bejne/sLp5i8aXt7WRpqc.html

@sharpcarco 4 жыл бұрын

Also my tips and tricks playlist is pretty good I have some pretty neat stuff in there kzfaq.info/sun/PLWSrc_bUH2bWfS2aksuY1uEDNOqzlffF3

@AgeofReason 4 жыл бұрын

@@sharpcarco thanks man. I'll tune in.

@User-wo4vh 3 жыл бұрын

Thanks for the video...Keep the jokes coming, love it

@uainttheone Жыл бұрын

I'm really hoping that will work for my case here... The bolt that holds idle arm on my truck got stripped at the bottom because he's a piece of s*** other nut came off and cross threaded end of the bolt. Can't get the nuna on there started I've tried to file it and everything

@veganath Жыл бұрын

Still being appreciated, thanks

@sharpcarco Жыл бұрын

You're welcome!

@plusblood5101 Жыл бұрын

Gr8

@bilbobaggins1000 3 жыл бұрын

Wow. Didn't do anything but tear up my part. Cost:$150

@jeffreyco7806 2 жыл бұрын

cool!!!

@sharpcarco 2 жыл бұрын

Thanks sometimes we get it right…

@jackofalltrades9492 2 ай бұрын

That's cool man but your hacksaw is about a foot long do why only use maximum 1/3 of it? Most people do the same thing even with a timber saw. Cheer

@enriquecortes5184 Жыл бұрын

I love the video but not what i was looking for . Need to remove a bolt then tighten it back in, looking to remove the cross threaded bolt and then re tap the same hole for a bigger size bolt to hold it in place

@sharpcarco Жыл бұрын

Sorry brother this is some hack Yvonne hockey stuff in this video…. The one and only time I ever did this trick… but I could see where it would be useful for some people

@bssandhu07 4 жыл бұрын

Hey This was a great trick ... However I have a question I used this trick to put one of the bolts for my trailer hitch on the Van... I am concerned about if it weakens the ability to pull the trailer ? anything you can explain in that context ? Thanks

@sharpcarco 4 жыл бұрын

Well like I said in the video you have to use common sense if you only have two bolts holding something DO NOTdo this! . Just want to make sure you understand I’m not saying that in your situation not to do it because I don’t know exactly how many bolts you have holding the trailer on but it is one of them things that you have to realize is not a practical fix I just think that there was certain situations where this technique and trick would actually be just fine like say you’re trying to bolt a exhaust bracket to something in the exhaust is bolted down district would be just fine for that but if it’s anything that requires a safety situation I personally would not do it I would loosen everything up and do it properly.

@bssandhu07 4 жыл бұрын

@@sharpcarco make sense thanks!

@FahadManiar Жыл бұрын

wont help the situation im facing but i did learn a new word... Kitty Wompus lol

@sharpcarco Жыл бұрын

All the good old kitty Wompus!!! that’s when your stuff is jacked up and crooked!!! Thanks for the smile. I forgot about that one.!!

@VondaInWonderland Жыл бұрын

God bless you too. I just changed my radiator and I screwed the bolt to my transmission cooler line into the main bolt kinda wonky, and it sprayed out everywhere. I took it out and tried to screw it in straight, and it won't screw in. I think that I stripped it. Would this trick work on starting it in too? Thanks for your time ♥

@sharpcarco Жыл бұрын

You would have to really be careful with that…. I’m assuming it’s plastic. I would hate to see you split the radiator but then again it’s already broken….. that’ll be interesting to see what happens so keep me informed God bless you too my friend welcome to the channel and we are very happy to have folks like you here….

@VondaInWonderland Жыл бұрын

@@sharpcarco It's a brand new radiator, and both pieces are metal. I ca see 2 new sideways trails where I twisted it in. They have messed up the normal trails at the beginning, so I can't even get it started. Thank you for getting back to me 🙂

@briancraft777 2 жыл бұрын

Would you trust this to use on an exhaust header bolt? I cross threaded one and it won't go in all the way in now

@sharpcarco 2 жыл бұрын

Are you going to remove the stud? And put some washers behind it. You could probably run a tap if you’re removing the stud and put it incorrectly just run the tap down blow out the whole after you run the tap down. Or like I said just remove the stud put some washers on it after you measure how far it actually goes in it’s not like you’re going to be able to hurt somebody if it doesn’t work so I wouldn’t worry too much about it but fixing it right would also be good to.

@briancraft777 2 жыл бұрын

@@sharpcarco I actually Installed aftermarket headers and new bolts. All if the bolts started but this one. It looks a little crooked. I had to stack washers and tighten slightly but I really want to get the bolt to seat properly

@ohnemar4285 2 жыл бұрын

Remember, jar your farts. All of 'hem!

@feralfreebirds 3 жыл бұрын

ah love the end....'you can do it too,....i HAVE been trying to get a bolt out from back of engine, holding my crank case sensor on, and it must be cross threaded...the bolt goes around, but wont come out, its a pig, as you have to do it all by feel as you can't see it..., im so frustrated been trying to do this for months and still can't get the bolt out..any sugestions???? as yours was out already...tried to get a level into the slimest gap (like a finger nails depth) to pull as ratchet...but still not worked...any help welcomed please

@olenaerhardt7725 3 жыл бұрын

Attaching the new brakes, I crossed the bolts. They went in very hard, I thought it was because of new rubber inserts (they came together w/new brakes) I put in holes for those bolts. They stopped ~1/4 in before the end, where they are supposed to be, and started to rotate free both ways (clockwise and counterclockwise), I can't extract them, because they rotate. Can I drive a car with these bolt for a while, since they don't come out before I buy a new knuckle, and actually I don't know how to extract them? Thank you for the good film.

@sharpcarco 3 жыл бұрын

I’m sorry to say I’m sure you need your car but I would have to say No !!

@olenaerhardt7725 3 жыл бұрын

@@sharpcarco Thank you. Actually I think I just overtightened it. It might sits in its place, so means it would be some problem on the next brakes work. Do you happen know how to extract it. Did you ever dealt w/such bolt (it is a slide bolt w/a thread at the end).

@sharpcarco 3 жыл бұрын

Send me a PM on my clays Ac and auto repair over Facebook and I will try to help you deal with it . Seeing a pic or very short vid will help me answer it

@olenaerhardt7725 3 жыл бұрын

@@sharpcarco Thank you for your attention to my problrm, Sir! I extracted those two bolts yesterday, the picture was: one bolt was broken completely (threaded part was left in the hole of the knuckle, and the cylindrical part was by itself in the caliper), and that is why it was rotating freely, another one totally messed up the thread in the knuckle hole, as well as its own thread, so also rotated free. I ordered new knuckle, both to be on the safe side. I think that would be the best solution for the brakes. God Bless!

@quantum7145 Жыл бұрын

why didnt you just use the impact wrench right away or did you?

@sammazon1841 11 ай бұрын

I'm no mechanic nor am I even close. Only thing I know is the cars are supposed to work. Lol...inherited a 2001 Ford Windstar but the thermostat housing bolt was drilled, wring size and tried to force wrong size bolt in it. It snapped off. I got the bolt out with needle-nosed vice grips. My problem is I need to retap this hole. How?

@MoeLarrycurly1 4 жыл бұрын

👍🏼👍🏼👍🏼🖖🏽😊

@davidclaypool-eg8bf Жыл бұрын

My situation is I'm trying to pull the flywheel on a GY6 150cc scooter and inside the flywheel

@21boxhead 3 ай бұрын

WHAT HAPPENS IF IT'S THE OTHER WAY AROUND INSTEAD OF THE BOLT IT'S THE NUT?

@batolokg 2 жыл бұрын

Mister where are you to bring my van to you t fixed thks

@sharpcarco 2 жыл бұрын

I am in Muskegon Michigan now You can reach me at Clays AC and auto repair on Facebook messenger and send me a Dm Or Email Thenewclayway@gmail.com

@60000L 3 жыл бұрын

Maybe Mercedes can try this on Bottas' car

@charleschase1300 3 жыл бұрын

Ooooshsh muuuhdd muouoini eeee!

@martydockery-mh8ln Жыл бұрын

How to keep bolt from turning in a 2002 satern sl sway bar right side

@martydockery-mh8ln Жыл бұрын

It came out once put ne bushing in it how can I keep it in the sway bar tight

@martydockery-mh8ln Жыл бұрын

Help

@balloney2175 3 жыл бұрын

Is there a way I can borrow your anvil?

@sharpcarco 3 жыл бұрын

Lol

@jimbo427vette 4 жыл бұрын

as long as it took to cut that bolt you could have easily loosened the other bolts and ran the third in and been done in half the time>

@sharpcarco 4 жыл бұрын

True but not the point of the video.

@sharpcarco 2 жыл бұрын

Still not the point of the video… if you had watched it either of you would’ve knew that I only did it to demonstrate the process …..

@supersabrosinho Жыл бұрын

Starts at 1:43

@benjaminmcelwee1567 2 жыл бұрын

Kittywompus

@sharpcarco 2 жыл бұрын

Yeah I hate it when stuff goes kitty Wompus On ya in the middle of a job ….

@myfinalfantasy3607 4 жыл бұрын

How to take out a screw with damaged threads?? Like the screw is neither getting tight nor is it getting loose so that I can take it out and put a new one in. Please help me out man.

@sharpcarco 4 жыл бұрын

Well you take a pair of pliers and you put it underneath the screw and as you try to turn it out you pull up on it and it will come out unless it has a nut on the back side that is spinning

@myfinalfantasy3607 4 жыл бұрын

@@sharpcarco Alright thanks man. Have a nice day.

@phillippardo5712 Жыл бұрын

Can someone explain why or how this worked?

@sublime929 11 ай бұрын

Look at the bolt after he cut it, it has two sharp edges on the threads, they will kinda like a drill bit and cut new threads in the hole.

@Izediddy 2 жыл бұрын

So… was it cross threaded?.. or the bolt hole was just not 100 percent lined up?, two different scenarios

@sharpcarco 2 жыл бұрын

Wouldn’t matter. I’m fairly certain I described that in the video

@jegr3398 2 жыл бұрын

@@sharpcarco no need to bother lining up the hole when you can just hacksaw the bolt right? I feel bad for the guy who buys your used hunk of crap truck held together with hacksawed bolts. Holy shit.

@SwastikaHinduSansrkit 3 жыл бұрын

You're compromising the strength of the bolt

@sharpcarco 3 жыл бұрын

Lol , thanks for letting me know I wouldn’t of figured that out by cutting a line down through the center of it.....

@NEOMASSO 4 жыл бұрын

Kiddy wampus

@joshuarayne9144 4 жыл бұрын

You should probably warn people that what you've done here significantly weakens the bolt and could lead to failure. And not to use this "trick" on and bolts whos failure could put lives in danger.

@sharpcarco 4 жыл бұрын

You should probably watch the video. Yes putting “lives in danger” 🤔 Wow

@joshuarayne9144 4 жыл бұрын

@@sharpcarco yeah. A broken suspension pivot bolt at highway speed could be deadly to not just the idiot who followed your advice but possibly also those around him. Just because you're too lazy or ignorant to not cross thread a bolt. Please stop making videos, for the good of all.

@sharpcarco 4 жыл бұрын

Well it’s been said before the common sense just isn’t very common anymore Unfortunately I do not have the time to have a battle of intelligence with an unarmed man .

@juliogonzo2718 4 жыл бұрын

@@joshuarayne9144 it's just holding a differential in, I don't think it's going to fail catastrophically. Kinda a halfassed way of fixing something, but not a brake, wheel end, or load bearing fastener.

@joshuarayne9144 4 жыл бұрын

@@juliogonzo2718 that may be so in this case. But invariably, since no warning was given not to use this trick on something like a lower a arm pivot, there's a good chance that some unsuspecting unknowing person could cut a slice 3/4 of the length of their shackle bolts on front end of their 74 Ford highboy and have their whole front axle fold backwards at 78 mph. And that could be VERY bad. I just think that taking an extra 22 second to warn the ignorant earthlings not to use it in a situation like that would have been a good idea. And that it's kinda irresponsible not to have done so.

@TheCommo81 Жыл бұрын

Why don't you just run a tap through there and clean the threads? Wouldn't that be easier to buy a $3.00 tap?

@thereviewer4173 3 жыл бұрын

A similar idea would be to use a bolt that is one size bigger. Not sure how well this would work though.

@GuitarGuy650 Жыл бұрын

If the propper sized bolt isn't seating, how would a larger one?

@hokiemiata 3 жыл бұрын

Great trick, no doubt, but this video is annoying to watch. Thanks !

@dreddmann9292 Жыл бұрын

man, I would be fucking pissed if a mechanic did that shit to my car. even if my car was a pos (piece of shit) I would still be fucking pissed off cause this kind of work could lead a car ending up on the road in pieces. This is a temporary hack and it's definitely NOT a way to fix this kind of problem. So DONT call it a SUPER FIX!!! This is a quick temporary SUPER HACK!!!! NOT a SUPER FIX!!!

@sharpcarco Жыл бұрын

Ok captain I don’t think ahead but I will pretend, you have the same resolution ether way, you have a stripped hole when you started ………. And you have a stripped hole when your done …… unless your saying the bolt is gonna fall out ….. same result either way so what is your point ….. please don’t answer I don’t care cause you obviously did not listen to the video this is not a common practice……… this is you tube …. This is a hack trick and btw the bolt is still in there and this is my truck so EAD ….

@dreddmann9292 Жыл бұрын

@@sharpcarco calm down princess. all I'm saying is DON'T call it a SUPER FIX. Just call it what it is, a SUPER HACK. Since you agree that it's a hack trick, no need to get all emotional about it princess. I swear guys on KZfaq act worst than women.

@sharpcarco Жыл бұрын

Yeah I’m a bitch sometimes…. 🤔😂 but when you make videos to help people that are free for them and they constantly bitch and complain and whine……. Well it gets a little bit old….

@jamesdearman814 2 жыл бұрын

ditch the bs at the bottom of the screen!

@matreyia 3 жыл бұрын

Let me know when you make videos without the news ticker text below. I'll actually watch them and click like. I could not finish this video due to the distracting text that had nothing to do with the discussion.

@sharpcarco 3 жыл бұрын

I don’t do it all the time but there’s people who like it and there’s people who don’t.... I do it because it’s my channel and I enjoy the information and I love being in a social setting where I don’t know many people and it gives me something to talk about and makes me seem more interesting. At least that’s my opinion but you have yours as well I still wish you the absolute best and I’m sorry that you wouldn’t be a part of this great Channell have a great day God bless

@sharpcarco 2 жыл бұрын

⭐⭐⭐⭐You can further support us by using these links to purchase anything from Amazon! So here's some things we like to have around the shop! (you can buy anything with these links and it helps us out, not just the linked items) FOXWELL Car Scanner NT604 Elite OBD2 Scanner ABS SRS Transmission, Check Engine Code Reader, Diagnostic Scan Tool: amzn.to/3vmTYhu 60 PCS Tap and Die Set Metric and Standard Sizes: amzn.to/3MkcFtl\ Craftsman 20 Piece 1/4 Drive Metric Socket Set: amzn.to/3xEltpy CRAFTSMAN Hand Saw, 12-Inch Hacksaw (CMHT20138): amzn.to/3uUijfE

@trspanda2157 3 жыл бұрын

Who here believes that Jesus died for them to go to Heaven when they die and whoever believes in him shall not perish but have everlasting life😔🙏

@fredlabansr.9995 3 жыл бұрын

❤️

@mitchib1440 3 жыл бұрын

I really think it would be better without the pointless facts across the bottom. It's so distracting

@sharpcarco 3 жыл бұрын

Distracting..... 🤔 hmm ya don’t say . Some people like it some people don’t

@undergroundlegend198 2 жыл бұрын

Nonsense

@UnkTob 4 жыл бұрын

Nope. Not watching this. I thought you might have been helpful adding captions across the bottom. Nope. Just stupidness. Disliked.

@sharpcarco 4 жыл бұрын

Good job troll lol 😆

@UnkTob 4 жыл бұрын

The Clay Way Not trying to be a troll. I t was just so annoying I felt it would be good to explain why I gave it the thumbs down. Hope you and your channel do well. 👍

@jonathansimmonds5784 2 жыл бұрын

It would take a helluva lot less time to watch these videos if the people making them didn't like the sound of their own voices so much and stopped waffling on and on, just get on with covering the bloody subject ffs!

@sharpcarco 2 жыл бұрын

Yeah it would also be a lot nicer if people wouldn’t bitch about something that they didn’t pay for…. Whiny asss