Stryker Front Pulley Swap

Рет қаралды 18,057

11 жыл бұрын

A video showing how to swap your stock 31 tooth pulley on the Star Stryker to a 30 tooth pulley found on the V-Star 1100. This will lower your gear ratio, making low speed riding, 2-Up riding, and starts easier with less clutch.

Пікірлер: 22

@alnoel3089 7 жыл бұрын

this pully swap use's a 30 tooth pully from a 1300 Vstar part # 3D817651-00-00 some of you where asking now you know, I have done it and it makes a big differance

@maniacalmango 10 жыл бұрын

He's explaining it correctly. Less teeth means smaller pulley which in turn gives you more low end torque= Faster acceleration but loss in top speed.

@maniacalmango 8 жыл бұрын

+Gus Guti It requires more effort if you shift to a bigger front gear. I've replaced my front pulley with a smaller one and have much more torque and lower top speed. Jump on your bicycle and they it and you'll see I'm correct.

@RickGoodman1911 7 жыл бұрын

Alot of 950 riders are doing the exact opposite to get better top end. Going from a 30 tooth to a 31 tooth pulley.

@skwerlee 10 жыл бұрын

Nice video. Going smaller on the front pulley or larger on the rear lowers the final drive ratio which improves low end torque while slightly reducing top speed

@xarrow81 9 жыл бұрын

What I want to know, is it worth it? Its been a year, whats up

@Joey.Darkwoods-Studio 2 жыл бұрын

Nice. Was looking into this... but the manual mentions adding loctite to the bolt don't they?

@robertdepczynski6192 8 жыл бұрын

i need your 31t pulley..lol

@tylere1195 8 жыл бұрын

Could you post a video on the proper alignment

@530powerstroke Жыл бұрын

Do you still have the 31t? Do you want to sell it?

@paultheage-lonerider 5 жыл бұрын

It could be good the Bolt 950 pulley???

@bigpowerhouse11 3 жыл бұрын

What is the size of the nut on the front pulley?!

@michaelreilly3933 7 жыл бұрын

has any one found where to find a 31 " front pulley ?? I have a 2009 950 v star

@jesseberg6183 6 жыл бұрын

i have one if u still want

@ryanamy1129 5 жыл бұрын

@@jesseberg6183 still have the 31t? What's it from?

@Group_Anonymous 5 жыл бұрын

Did you crash your bike

@MrMmari Ай бұрын

Hi - good job. How many teeth does the pulley you use have? I want to put another smaller pulley with fewer teeth (the original is 30 teeth), could anyone advise where to buy? The original transfer is too long. Thank you

@tms372 7 жыл бұрын

Where did you get the pulley? The yamaha dealer said there not available.

@alnoel3089 7 жыл бұрын

this pully swap use's a 30 tooth pully from a 1300 Vstar part # 3D817651-00-00

@FrancoSattamini 10 жыл бұрын

Hey man, the video is nice, but . . . I believe your thinking as far as the effect of the smaller pulley is opposite of what you are trying to achieve. The larger the pulley, more belt pull will happen with 1 full turn of the engine shaft, hence more torque (I believe you said more low end torque in the video). It is the same as shifting a bicycle. Did I understand you wrong as far as what you were trying to achieve? Peace!