Subaru clutch creaking, cause+EASY FIX! (Works on MOST manual transmissions)

Рет қаралды 12,648

3 жыл бұрын

If your clutch is “creakin, popping” or even “squeaking” when pressed/re-leased, this video could save you a lot of time.
This will work on pretty much any manual trans with a slave cylinder.
Glad to help!
JDM 2004 Subaru Legacy BP5 GT-B
5 speed Manual trans
Instagram @ Kamblxxk
Thanks for watching!

Пікірлер: 24

@johnjoe9918 Жыл бұрын

“Don’t want to use too much”. Proceeds to spray half a can 😂😂

@Kamshaft Жыл бұрын

😎

@zigwil153 9 ай бұрын

Was wondering when he was going to stop after mentioning... good vid

@vindeagle 2 жыл бұрын

yooo i had the loudest creak and this worked like a charm. saved me a trip to the shop thanks!

@Kamshaft 2 жыл бұрын

I appreciate the comment, and I’m glad this helped you man!

@JWheelie 3 жыл бұрын

Hey hey hey, NICE SHIRT and nice strudel! I have had this noise on all 3 of my subies on and off so this will definitely help a brotha out 👍 Thanks for the kind words, and for always helping me out when I need it Kam.

@stephenkeeffe4940 Ай бұрын

Now that was a big help. I don't have a WRX, just an Impreza R with that very problem. Thanks,

@stephenwright414 3 жыл бұрын

Nice lighting and camera angles. Music during your work is a bit loud though!

@Taranagu Жыл бұрын

The innuendo lol. Helpful though, need to do mine 👍

@jonjohns7080 8 ай бұрын

Bro I’ve been having this bugging the shit out of me I’m gonna try thank

@Kamshaft 8 ай бұрын

LOL 😂 yeah that’s a side effect

@boblincoln9152 8 ай бұрын

Same shits driving me nuts

@PhillipeGustavo 10 ай бұрын

Isn't that too much grease? It may lead to a clutch contamination.

@Kamshaft 9 ай бұрын

I did not have an issue, but you do bring a valid point.

@liangfengrui1990 Жыл бұрын

buddy, i followed your steps but i can't seem to place back the rubber boot to its original spot on top of the clutch fork, is it a big deal? thanks.

@Kamshaft Жыл бұрын

Yeah it kind of is a big deal as you don’t want dust/dirt getting in there. Keep trying till you figure it out.

@liangfengrui1990 Жыл бұрын

@@Kamshaft thanks for your reply buddy. i got 2016 wrx and the clutch master cylinder is in the way to place the rubber part back. in that case, im thinking of removing the master cylinder and place the rubber part back again. is that anything i should watch out for? is it okay to remove the master cylinder and place it bacl? thanks

@Kamshaft Жыл бұрын

@@liangfengrui1990 slave cylinder or master cylinder?

@liangfengrui1990 Жыл бұрын

@@Kamshaft my bad. the slave cylinder. is it okay to remove it and easily place back? thank you so much!

@Kamshaft Жыл бұрын

@@liangfengrui1990 it’s easy as long as you don’t remove the line that’s attached to the slave cylinder or you’ll have to bleed the clutch. And when you remove it make sure you don’t loose the pin in the slave, sometimes it will fall out, it just rests in there. Otherwise, very straight forward.

8 ай бұрын

Hello! And is it working properly since then? Didnt you have any issues with the clutch fork? I am asking because we did the same to avoid that noise but after a while it just broke :(

@Kamshaft 8 ай бұрын

Worked great until I was rear ended and the car was wrote off.