I have installed thousands of these systems in the 90's and injectors, chemical dispensers, iron filters, water softeners, UV filters and a ton of other systems!

Great video, most good techs are not afraid of giving out expert instructions because they sell their craftsmanship and most importantly the customer trusts them. Any tech who can explain what they’re doing they’ll usually get my business and I will not look for someone else.

Great video. Would love to see some more closeups of your plumbing connections and wiring once finished. But I'm loving the channel. Lots of good stuff here. Thanks.

I really like your roller that you use to install. I've done hundreds of these and that one tool would have made life a lot easier

I believe this will end up more of a question than a comment. I have somewhat of a unique situation compared to most of your well/shallow well videos I have watched. And thank you very much for putting out such practical DIY (some/most) videos, I know some situations require professional help. My situation is this, I live on a small river lake in South Central Texas. I have an above ground 3/4hp pump running our 9 zone yard irrigation system that was professionally designed and install by me and a couple friends over 30 yrs ago and has run flawlessly for 30+ yrs. But for that last 6 months or so my above ground pump started leaking at a gasket in the pump. I was given a used operating (Goulds 10EJ15412) 1&1/2hp submersible pump that was replaced in a deep well where my son-in-las worked that I now want to replace the above ground pump with. It will sit about 4-5' below the lake water surface level to prevent sucking any air when boat waves come by and pump up through pump shed and pressure tank then uphill about 25' rise at a 45 degree angle 200' up the length of our yard feeding the 9 zones and 4 sporadic faucets. It is not an option to change any of the 1 1/2" piping, some of it goes through concrete seawall. Since the 1 1/2hp submersible pump has what looks like a 1" or 1 1/4" threaded output, - will I loose much pressure and/or volume plumbing this pump to an irrigation system that has all main lines are 1 1/2"? Right now the above ground pump will easily run 1 zone and 4 hoses with sprinklers watering the edges and areas the irrigation system do not get. At the zones the pvc drops to 1" and then to 3/4" and finally 1/2" usually at the last sprinkler head. Basically leaving the pump at it's 1" or 1 1/4" output then immediately transitioning back up to 1&1/2" prior to the pressure tank and cutoff switch (which will be located in the pump shed). - there is an external foot valve on the pump I was given, do I need an external foot valve for this type application where I will be able to easily pull/service the pump at any time? I saw on one of your videos you recommend this but I believe you said only on a deep well installation. - I am hoping my application will allow the pump to run constantly while the irrigation and/or faucets are running and not cycle the pump on and off, any ideas? Are those cutoff switches adjustable to keep the pump running when needed? Thanks for taking the time to put out your videos, I have found them packed full of knowledge and very useful. Paul in Texas

Always a good videos from Phil, with his videos, I was able to replace all components of my deep well and now have a running well! He even replied To my question when my new install did not work, diagnosed it was a broken wire, replaced the wire and it started working. Keep the videos coming Phil.

Thank you for the time you put into these videos. It is amazing to me how many people use pump pliers backwards... This guy uses them properly everytime. 😀

4:42: one thing you don't comment about the rubber tape... stretch it a bit, and it self-sticks and helps seal better to keep out moisture. I used it for sealing connectors up a tower, but as rubber tape is UV sensitive... needed to cover it with electrical.

This video was super helpful for me. Thank you!

A topic I never hear you mention is the size of the storage tank. In instances where there is space and the well produces enough water, I understand it is better to use a larger tank versus the small blue and white tanks. From what I read, the benefit is less startup on the pump. That means less stress on the pump (longer life), and less instances of needing startup current.

When using stranded wire under a screw put a left hand twist in it to prevent the wire from being untwisted.

I've watched many of your videos, enjoyed them all. Why not put the wire spool at the other end and pull the wire back towards the pump? Then it will never be short.

Always interesting to watch your video`s Our wellman in this area of Pa puts tank in ground its fiberglass with bladder inside and puts the switch with gauge inside the well above the pitiless adapter. So no freezing here in the North

Can you make another video with how to open and close the season with this kind of setup? I live Canada where pipes freeze....so I can't have any water in pipes or pressure tank ...

Great video! Wish i could find someone with your skill set and honesty down here in Texas.

For a situation where you want to use a generator with a well, is it worth adding some kind of a soft start circuit to cut down on the starting amps?

I enjoy the videos it's guy stuff and I like it. They are never the same always new obstacles to over come. Keep them coming cause I enjoy everyone of them.

excellent narration

Well done Phillip!

Enjoy your teaching us, as for myself tho i cant hear you clearly over the music.

Wow. Don’t ever come an work in Australia, Franklin would give no warranty on that installation. We need to use rubber cable and double heat shrinks.

Pro top: Never cutt towards yourself, always cutt towards a buddy!

Great content as usual, but your background music is distracting.

2023 hope this channel grow more 🦾

Greetings from New Zealand .... Totally on the Other Side of the World ...... :-) :-) :-) I just love All of your vidclip .... But Every Time I am just so dissapointed .... You go thru' the Whole Thing, but we NEVER see the result and see the WATER gushing out.... :-) :-) :-) This is in MOST of your vidclips .... The whole point of you doing ALL that Work is to give the customer water and we would Also like a taste of it too ..... :-) :-) :-) .... Best to You, Yours and All others, Cheers from ChCh, NZ

I guess it really depends on the area, but I would think even for a temporary setup I would run conduit from the well into the pressure switch and use SOOW for the power pigtail and plug with water tight glands on all connections. A way of doing it without the conduit would be using the appropriate gland on the three wire zip cord from the pump. I don't know if there are pressure limit switches that are also water tight or whether that's needed but just something I would personally feel comfortable using.

Did your dad teach you how to teach people? You are one hell of a good teacher. They cant pay teachers 100's of k that are as good as you. Damn.

I always use a pipe coupler and then an elbow or a tee with on side plugged on top so the pipe will hang straight down. I noticed that one is cocked some. On a well like a 100 ft or less I use a 120 volt pump. It is much easier to hook to a generator and some generators don't even have 240 volts. But you will need around a 3000 wat generator to handle the current surge when the pump starts unless it's one of the high priced soft start pumps.

What are those yellow handled wire strippers that you use?

Great video, yet again! Your videos are always helpful!!

Looks great, but since it is outdoors that wire should be run in flexible conduit.

At 9:35 can see the house that`s a fixer upper ,but it`s home .

Have you guys ever used marine epoxy lined heat shrink? I prefer that heat shrink, but you do such a damn thorough job with that tape I bet you never have an issue out of it. I prefer epoxy heat shrink just because it looks cleaner.

I wish you coulda tried it, it woulda be really REALLY NICE TO FIRE IT UP FOR THE FIRST TIME. ALSO YOU MUST BE IN A HOT WARM TEMPURATURE STATE, UNLIKE HERE IN SD, NEBR, COLO, KANSAS, MONTANA, ALL OF OUR SUBMURSABLES AND 80 GALLON TANKS ARE IN A 6' OR 8' TRENCH UNDERGROUND COVERED UP, IT FREEZES HERE ALL THE TIME 🥶🥶🥶🥶😳🤯😵😱🥶🥶🥶 GREAT JOB!! 😉👍

5:52 I knew you was gonna talk about zip ties

I am not sure if you answered this in another video but I would love to see a simple wiring schematic/explanation for what wire goes where when you connect the three pump wires to the yellow submersible wire and then connections topside. Do different pumps (more or less horsepower) require different wire gauges? I assume you run underground feeder to the connections topside of the well? Thanks man, you are putting out great content.

Thanks!

Great video and content 👌

Your videos are great! Could you suggest a water depth meter?

Thanks for the great videos. When and why are check valves installed on the down pipe sometimes?

A couple questions. Don't shoot the messenger. #1. Should the well have been shocked by chlorine. #2. Should the well have been bonded.#6 wire.(grounding rod) Since the well is not steel, A PERSON doesn't want a lightening bolt to Fry the pump. #3 should a disconnect switch have been installed at pump, maybe screwed to a wood stake, near the well. #4. How would a person release the water, back down into the well, if there was a chance of freezing temperatures, to prevent the pvc from cracking. Now the patch cord was only 10 feet or so. The owner was also powering a camper and The patch cord could be changed to 75 feet long next to camper. We all know that temporary sometimes stretch a little bit. I'm just

Very thorough! Thank you.

Been seeing signs for your company around crowders mountain

Good video, but I was disappointed when you got to the end and did not check out the performance using a generator you provided.

I looked for but missed any others asking this, but I am curious about: A) Check Valve? I didn't see one installed. Necessary? Maybe built-in to the pump and not needed on shallow well? B) Did you set the pump directly on the bottom of the bore? The casing was 80ft deep and I thought I saw you drop the pump to 80ft. Will sediment be a problem over time causing turbidity?

How could a guy get a hold of you as I have a few questions about my water system in my home. I have a 400gal fresh water holding tank, that runs to a 1/2hp non submersible pump with a flotec tank. I have set everything up the way you have shown in previous videos on your channel but I'm still encountering an issue. If I could shoot you an email that would be sweet! Happy holidays to you and your family! Thank you for the wonderful / educational content you put out!

Saving penni for a adapter

Is there any well pump that will go down a 2 inch casing a 188 feet and supply water well 360 feet 8 gallons per minute

How accurate is the well tag? Specifically you state that you want to keep the pump inside the casing, the tag says the casing is at 80 feet and you indicated you were going to put the pump 'at 80 feet'. If there is any inaccuracy in your measurement (on the long side) or their measurement (on the short side) then the pump will be outside the casing. Would it not be better to set the pump at 75 feet (something close to, but not AT, the end of the casing)? Also - I do not recall seeing you 'shock' this well before inserting the pump whereas I've seen that done in another video, was that not required for 'this' setup or was it done prior to the start of the video?

Do you think you could run a well pump off a solar panel system

Thank you for sharing these videos. I enjoy watching you work, very professional. I am wondering why you don't use any UNIONS in your piping? I have used them in many applications. When having to make any repairs, like because of broken pipes or whatever it makes disassembly easier and I don't have to cut out a lot of good pipe. For instance, if I had to change the bladder tank as you have it installed, I could disconnect at the union.

I don't see any primer! Is this a new type of glue that doesn't require primer?

Recently found your channel and did subscribe. Great content! On one of your previous videos the subject was the PVC pump sleeve to protect the pump motor. When I replaced my shallow well submergible , about 6 months ago, I found on Franklin's site their advising using these PVC sleeves particularly on larger diameter wells to insure pump motor cooling. I have a 85 foot 24" curbed well and it had gone through 3 pumps in 15 years, due to motor failure. I am convinced that had I installed the PVC sleeve on pump number one, I would still be using pump number one. Was wondering why you did not include the PVC sleeve on this 10" shallow well?

Awesome video Great work !

Do you have a Franklin Aid document on 2-wire motors and generator use and effects to the Franklin BIAC switch? Its not in the AIM manual. The Franklin AID is an old monthly doc, Franklin published in the past.

Awesome

I have worked with 230V motors in the past and know I can change the rotation direction of the motor by switching 2 of the wires. Is motor rotation a concern for well pumps?

I'm curious about the white silicone looking material used to seal the wire where it enters the well. It appears oddly supple, just screams of quality, is it some 3M product?

How do you keep the line from freezing?

do you install well pump

Wish you would have shown how to wire the pressure switch

H2O how do y’all know how much water a well will make?

you always show putting a bad of shock in the well but not this time is it because it is a shallow well

Could you give information on the wire you use. Gauge, volt

I couldn’t help but notice you didn’t sanitize as well prior to installing the pump. When is that required?

4:17 Bush hog coming up behind you

Won't that freeze in the winter?

Bro what is black pipe?

Can you use solar system instead of generator in this setup! If yes what size? Thanks

Thank You

I got a question when hookin wire to the pump how u kno which colored wire is which

Thank you for this video. Speaks right into my situation. My off grid well produces 10gpm. I have a 23gpm submersible pump. Is there a way for the two to work together without running the water dry? Thanks in advance!

Thankyou for having this channel! Ive never had to hook up a well before, but I now am in the process and I’m learning. Trying to learn from reading online and watching your videos. I just got a well drilled to hook up to my mobile home. The well is 100ft, 15 gpm, 8ft static water level. Should I be concerned that the static level is so high?

Are sure pvc will stand the winter freezing temperature?

How far away from the well can the home be? When it is piped with pvc. Could it pump 200-300 feet and give adequate volume and pressure for a small house?

Is POP-off valve necessary? Mine is starting to leak can it be removed or needs to be replaced?

Are using 1" or 1 1/4" tubing?

Ever considered using pex for the above ground sections?

Is there any reason you don't use a ratcheting crimper? A ratcheting one makes sure the connectors are all a uniform compression level, to make sure a good contact is made.

What’s your thoughts on a cycle stop valve?

Where can I as a consumer buy 600 feet of pipe and 600 feet of wires? I've only seen them sold in 300 foot lengths (except Menards but for some reason they won't ship to my NC address). Also what PSI rating should the pipe be at 600 feet? I saw blue 1" poly pipe rated at 250 psi. Thanks for all your great videos!

Did you replace that blue well seal plug with some type of vent?

Excellent video and really good music

Got to well over 200 ft deep was clear now just muddy what do you think's wrong

Is there a reason you use stranded wire on well pumps, and not solid core wire?

Showing how you wired the switch to the receptible plug is the only reason I was here. Nothing on that.

do you know whats a good size generator to run does well pump by chance ?

does a bladder tank ever need sanitizing?

👍🙂

COST?

So if the well is 50m how meters of the cable and the pipe needed?

I’ve got a 1/2 hp pump (240V) in a shallow well. But it can’t get more than 25psi. What should I look at first? I Would love to set it at 30/50 like the pressure switch is made for but I’ve had to decrease the pressure in the tank and reset the switch so it operates properly (proper cut on/off) but I want the higher psi. Do I need a 3/4 hp pump to get greater pressure? Something else?

Is it true that if you use too much pipe paste you will be tasting it in the water for a long time?

there is no information on galvanized water tanks non bladder how to set them up and how to set up pressure in them ????????

Did you forget the glue or is that all in one (Primer & Glue)?

Can I put a 40/60 pressure switch on a tank that does not have a bladder

That must be one big ass generator to start up and run a 240V 1/2 h.p. submersible.

I work at a well drilling company in ct we use steel casing pipe how come you don't steel more costly

👏👏👏👏👏👍🏽

Use zip ties easier