Just wanted to say that as someone with essentially no tube amp knowledge, your channel is both helping to amend that on a technical level and simultaneously one of consumer knowledge. Great stuff, and very entertaining.

Maybe Leo was a bit too popular with Surf rockers, he was waxing his board way more than needed...

These days, with a camera in nearly everyone's pocket, it's simple to simply take a snapshot of the circuitry so you can remember what the polarity of the replacement caps Is supposed to be. Or, stick a piece of painter's tape on the chassis and write on that. I'll admit that I sometimes mark things with a Sharpie on the *foil side* of a circuit board if I'm tracing a convoluted, complex circuit and trying to narrow down a faulty area or a defective component, but that's easily removed afterwards with alcohol and a toothbrush.

Great video! Many truths spoken!

Another member of closet queen collective! I bought a 1968 Ampeg Gemini II closet queen at a gun auction. Does the stuff in the back come with the amp? The amp looks brand new, and the auctioneer says, "Yes?" When I got it home, a 1968 Gibson Maestro Fuzztone, a Shin Ei made for Guild Wah, a Jennings Copicat made for Guild tape echo, a Shin Ei Univibe, a Clyde McCoy wah, a Dallas Arbiter Range Master, and a 1st year MXR distortion +. WOOF! $3000+ in old FX. The 12AX7 preamp tubes were all swapped out for Telefunken E803CCs. The previous owner had custom built cabinetry for high end recording studios. All his tools were also for sale. 3 working panel X-Y slide panel saws??! THAT SAYS ENOUGH RIGHT THERE! 8 band saws, including a huge Do All resaw as in a 50" resaw? That is a lumber mill type saw. Spindle sanders, a table saw with a 72 inch table and 6 foot extensions. a custom made hexagonal shaper table & 6 shapers, with over 200 bits? Easily a million dollars just in stationary power tools & accessories, and it was all OCD anal retentive immaculately maintained. His guns were just as babied as everything else, but I stopped bidding on the Walther P7 at $3500. It sold for $6000+. in the original box with 8 or 9 extra box mags all like new. $10K for the whole lot. I got the amp for around $800. I'd have bought all those tools but I didn't have a fleet of semi trucks to get them home.

Amps pick up cell phone noise and wireless router/modem/printer noise too. It's really kinda annoying these days that so much stuff "leaky".

Has this Super ever been outside its owner’s bedroom? It is bizarrely perfect. Even a museum has some dirt.

Love old FENDERS, I own 2. Almost 60 and one day they will go to my son.

Wax on. Wax off Danielson. Great example of an amp from that era. Gotta love it.

My first tube amp, got it for $275 at a pawn shop in Oak Cliff Tx ( Stationed at Grand Prairie Naval Air Station) 1985 The grill cloth was puke brown from life in bars!

It’s a beautiful day in the Fenderhood…..

Wow ! Beautiful condition .

“I’m an amp tech, not Fred Rogers.” 😂 love it!

Please don’t slam us new techs too much! We are still learning! P.S. Your videos are great!!

I picked up the Maxwell House French roast per your recommendation and I can confirm it's pretty good for the money. This is coming from a minor coffee snob haha.

Those original blue blob caps are notorious for becoming leaky, especially the ines that couple the phase inverter to the output tubes.

I introduced some odd noise in my research lab which perturbed the amps on the bench enough to warrant chasing down the culprit. I had moved my SONOS wireless speakers nearby to listen to podcasts. No can do ... -BigHammerLabs

I recently figured out my “ noise “ issue!! When playing, working on and recording my amps, I would have a staticy, putta putta putta sound. It was VERY low level, but annoyed me. I figured it was my phone, nope. Ended up being my Wi-Fi extender…. Unplugged it and the problem was gone 100%. If you have any type of Wi-Fi nearby, that is likely the cause.

Would you ever use a heat gun judiciously to warm op the board to emulate it being left on in the cabinet and getting 100+ degrees?

Good video 👍

Don't know about you,... But this is a real treat for me 😎👍 Thanks for sharing 😎👍

@15:29 the 470 ohm on right looks BROKEN, but cant be, or itd REALLY be nasty!

Not sure about wax, but brown goop will absorb moisture out of the air. Depending on how it's been stored the last few hours will determine if you can duplicate it or not.

You may have ruled it out,but cell phone can cause the noise you mentioned,our amps and mixing board have picked it up when phones are in close proximity.

Great video

I only play guitar in a Faraday cage.

I got one same thing 1976. I’m selling it. Nice piece

One amp I'd love to see you improve is one of the newer Supros, not the real cheap ones but the top line ones. I have a 24w Dual Tone and although I like the amp in some respects I think it could be a lot better with the right tweaks. The high end is harsh and could be softened.

Nice sounding amp!

As far as the "mystery noise" in the air at your shop, I've discovered that WiFi can do that........ You already know about the phone. All these over the air signals are causing chaos.

I have a challenge for you, figuring out why all of these DL4s from Line 6 just up and die. It's got to be something in the circuit, some sort of terrible wiring or short that slowly develops, consistently in all of them. I'm sure you could find some people to send you dead or broken ones to look at. I'd love to hear and see you go through one of them.

Fender logo doesn't have a tail, so that does say mid-'70s. But, shouldn't a '74 have a Master volume. If it was pre-Master Volume, the logo would have a tail. Is that correct?

Ha ha ha. Yea i am a victim of “phone on amp” noise.. i use my phone as a tuner… couldn’t figure our why my amp was making weird pulsing noises….

Could it be from your new video camera ? The tic tic noise you are having !

So what do you do about wax? 😮😢 I have a few amps in that range, but they sound great

I've got a 1970 Champ in even better condition.

@Psionic Audio Hi, what have been your experiences with Hiwatt Amps? I own a couple and I like them but I know other people may not like the clean sound. Do you have any opinions about them? Thank, Jacky

I’m very confused. I see tons of Fender Amps on your channel and all the shows I go to there are walls of Marshal Amps. Am I going a different type of show? I go to mostly guitar shows, Yngwie, Eric Johnson, Vai, Satriani, ect.

I love your channel as I was a commercial guitar tech for 20 years and worked hand in hand with amp techs such as yourself. I can't help but notice how when you choose a guitar to test with its almost always an odd combo i.e. tele/hi gain amp or SG/super. Seems to be a bit of amp tech trolling?

When did fender stop doing p-p wiring and employ printed circuit boards?

Hi there i can see the first 2 filter caps are 220mfd 350v , and should be 70 / 100 mfd 350v, a 45w super reverb with a rectifier tube cant handle that much filterng, and this amp is clearly a 45w, not the later ultra linear super reverb 70w with solid state rectification which did use 220mfd caps

What makes you think that an actual tech did the work? Could be a diy thing :)

Kendrick amplifier house brand of caps so who made them is up for grabs . The puda puda could be security system or some thing the computer or filming doing . Without being there to trace it down just A KEYBOARD WARRIOR rant at best.

Hoops corection. It’s a 1973.

Can you take some of the 1974 out and put in some 1964?

"nope. This is a 'real one'" 🙄 As if what you can buy today isn't a REAL Fender amplifier.

Do you offer an internship? Lol